Land Rover Defender Parts

A/C Switch - facia-mounted switch for the air conditioning system. Fitted in the heater and ventilation control panel of the centre facia, it is t...

Fuel Pump Drive Sprocket for the 2.0L Ingenium diesel engine (AJ200 / AJ20D4). The sprocket drives the high-pressure fuel pump from the engine's ti...

Brake Pad Set - Rear - friction pad set for the rear brake discs and calipers assembly, supplied as a complete axle set covering both rear wheels. ...

Gear Lever is the main gear selector lever for the manual transmission. The driver moves it through the gate to select gears via the gearchange li...

Valve Spring - V8 is a cylinder head valve spring for the Rover 3.5L and 3.9L V8 petrol engine. The valve spring seats between the cylinder head a...

Grab Handle for the interior roof trim, mounted to the body structure above the door aperture. The handle fastens through the headlining into the ...

Exhaust Heat Shield - a formed metal shield fitted in the exhaust system area of the underbody. The shield sits between the exhaust and the adjace...

Key - Mainshaft

Hose - Heater Water

Fuel Filter Shield is a protective cover fitted over the fuel filter assembly. It mounts over the filter housing and shields the filter body and i...

Washer for the bonnet insulation pad. This washer retains the sound- and heat-insulation pad against the underside of the bonnet, holding the pad ...

Body Washer, 22mm outer diameter, 6.5mm inner diameter. A flat washer that spreads the clamping load of a fixing across the mounting surface, prot...

Locating Dowel for the Rover V8 petrol engine. The dowel positions mating components accurately during assembly, ensuring correct alignment before...

O-Ring and Grease Kit for servicing the transfer box input shaft. Contains the input shaft O-ring and the anti-seize grease used when resealing th...

Inlet Air Seal for the Solex carburettor connection on the 2.25L 4-cylinder petrol induction system. Seals the joint between the air intake and th...

Vent Assembly Knob for the dashboard air vent control on models without air conditioning. The knob fits onto the vent control lever and provides t...

Bolt Mounting bolt for the power steering pump and front cover housing, and for air conditioning compressor and condenser mountings.

Gear Change Lever Knob for the transfer box gear change lever. The knob fits to the top of the transfer lever and forms the hand grip used to sele...

Cylinder Head & Sump Bolt Bolt used on the cylinder head and sump of the 2.5L Td5 five-cylinder turbo diesel engine.

Bolt M8 x 35mm hex-head bolt. General-purpose mounting bolt used to secure components such as the air conditioning compressor, differential housin...

Handbrake Shoe Kit - the retention (hold-down) hardware for the transmission handbrake, which acts on the LT230 transfer box rather than at the roa...

Screw - a threaded fastener used across several exterior body fixings. It secures fittings within the radiator grille, the rear end door seals and...

Front Cylinder Cover - a cover that closes off the front face of the cylinder block, sealing the opening and enclosing the components behind it. F...

CV Boot Kit

Door Opening Weatherstrip - the rubber seal that runs around the rear side door aperture. It closes the gap between the door and the body opening t...

Door Opening Weatherstrip - the rubber seal that runs around the rear side door aperture. It closes the gap between the door and the body opening t...

Timing Belt Tensioner

Rear brake disc, 365mm diameter, forming part of the rear brake disc and caliper assembly. The disc bolts to the rear hub flange and provides the ...

Drive Belt Tensioner - automatic tensioner for the front-end accessory drive on the AJ20 Ingenium petrol engine range. A spring-loaded pivoting ar...

Exhaust Gas Temperature Sensor for the post-catalyst position in the exhaust after-treatment system of the 2.2L Puma TDCi diesel engine. Installed...

Engine mounting bracket for 3.0L six-cylinder petrol applications - supercharged DOHC GDI V6 and AJ20P6 Ingenium. The bracket bolts to the side of...

Front timing cover - the lower centre cover that closes the front face of the cylinder block over the timing chain drive. It carries the crankshaf...

Exhaust Gas Temperature Sensor for the pre-catalyst position in the exhaust after-treatment system of the 2.2L Puma TDCi diesel engine. Installed ...

Rear Axle Pinion Repair Kit - service kit for the drive pinion in the rear differential assembly. The drive pinion transmits torque from the props...

Resistor Assembly sets the blower motor fan speeds within the heating and air conditioning system. Wired in series with the blower motor on the lo...

Fuel Vapour Valve (Purge Control Valve) - electrically operated solenoid valve in the evaporative emission control (EVAP) system, for supercharged ...

Radiator Hose for the engine cooling circuit. The moulded hose carries coolant between the radiator and the engine, and is shaped to clear the sur...

Steering Ignition Lock Housing - the housing that mounts the ignition switch and steering-column lock to the upper steering column. It locates the...

Supercharger Isolator - the torsional damping coupler inside the supercharger drive, sitting between the drive input and the rotor pack of the Root...

Rear Brake Disc, 325 mm diameter, part of the rear service brake assembly. Supplied singly. The disc mounts to the rear wheel hub and provides the...

Water Inlet Tube - rigid coolant connector within the engine cooling circuit, joining the thermostat housing to the upper coolant hose. It carries...