Land Rover Defender Parts

Wheel Centre Cap - a black alloy-wheel centre cap carrying the Land Rover oval in green and silver. It presses into the centre bore of an alloy wh...

Bolt and Washer - an M8 x 24mm bolt supplied with a washer, used as a general-purpose fixing across several Land Rover assemblies. The washer spre...

Bolt - M8 x 50 - Torx is an M8 threaded fastener, 50 mm long, with a Torx drive head. It is used as a general-purpose fixing across a range of bod...

EGR Cooler Filter for the low-pressure exhaust gas recirculation circuit of the 2.0L I4 Ingenium diesel engine. The low-pressure EGR system draws ...

Magnetic Oil Drain Plug for the engine oil sump on the 2.0L Ingenium (AJ200/AJ20) four-cylinder petrol and diesel engines. The plug seals the drai...

Oil Filter Gasket Kit for the engine oil filtration circuit of the 2.0L Ingenium (AJ200) engine, renewed with the oil filter element at each servic...

Oil Filter is the replaceable element in the engine lubrication circuit, capturing wear particles and combustion contaminants from the oil before i...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Thermostat Seal for the thermostat housing on AJ200/AJ20 series petrol and diesel engines. It seals the thermostat housing joint within the cooling...

Oil Cooler Gasket seals the oil cooler within the oil cooler and filter housing assembly. It maintains the oil-tight joint between the cooler and ...

Injector Refit Kit supplying the seals needed to refit a fuel injector on petrol engines. It restores the sealing interface between the injector an...

Accessory Drive Belt - multi-rib belt driving the engine's front-end accessories. Transmits crankshaft rotation to the belt-driven ancillaries wit...

Timing Chain Tensioner Arm bears against the timing chain within the timing drive assembly, providing the face through which the tensioner applies ...

Blanking Plug - timing chain cover, supplied with its O-ring. Seals a machined service aperture in the timing chain cover of the Ingenium engine f...

Bolt for the camshaft timing gear, part of the Ingenium engine timing drive. It retains the timing sprocket to the camshaft, transferring drive fr...

Timing Chain Guide - LH Primary - a fixed guide in the timing drive assembly of the 2.0L four-cylinder Ingenium petrol engine (AJ200 / AJ20P4), inc...

Antifreeze and Coolant Concentrate - red, extended-life engine coolant concentrate for the cooling system, supplied in a 1 litre container. The fl...

Arm - Timing Chain Tensioner

Spark plug for the ignition system of the Ingenium petrol engine range - 1.5L AJ20P3, 2.0L AJ20P4 / AJ200P and 3.0L AJ20P6 / AJ22P6, including plug...

DEF Injector Refit Kit

Variable Timing Solenoid - camshaft timing oil control valve in the variable valve timing system of the Ingenium engine range. The solenoid is an ...

Rear Crankshaft Oil Seal - the main oil seal at the flywheel end of the crankshaft, part of the crankshaft sealing arrangement on the Ingenium engi...

Accessory Drive Belt for the front end accessory drive of the 2.0L Ingenium four-cylinder engine (AJ200 / AJ20P4, petrol and diesel applications). ...

Timing Gear Special Nut from the front timing gear assembly, securing the lower primary timing chain guide. The nut locates and clamps the guide a...

Timing Cover Blanking Plug - threaded plug that closes an aperture in the front timing cover of the 2.0L Ingenium petrol engine (AJ200 / AJ20P4, al...

O-Ring - VVT Solenoid Cover, 47 mm, sealing the variable valve timing solenoid cover to the cylinder head on Ingenium engines - 2.0L AJ20P and AJ20...

Cable Connector - an electrical connector used in the vehicle wiring harness. The connector forms the termination between a harness cable and its ...

Mini Relay with four blade terminals, rated at 40 amp. A four-terminal mini relay switches a single normally-open high-current circuit under the c...

Mini Relay with four blade terminals, rated at 70 amp, grey housing. A four-terminal mini relay switches a single normally-open high-current circu...

Valve stem seal for the cylinder head valve train. The seal locates on the valve guide and wipes the valve stem as it reciprocates, metering the s...

Timing Chain Guide, Lower Primary from the front timing gear assembly. It bears against the primary drive chain on the run between the crankshaft ...

Exhaust Clamp for the 2.0L Ingenium diesel exhaust system (AJ200D / AJ20D4). The clamp secures the front section joint of the exhaust, holding the...

Timing Gear Bolt - special-form fastener used in the timing drive assembly at the front of the Ingenium petrol engine. It is one of the fixings th...

Timing Gear Bolt - a fixing bolt in the engine timing drive, retaining a timing gear. It secures the timing gear on the 2.0L four-cylinder AJ200 p...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

Cup Holder - an interior trim component fitted to the floor (centre) console. It provides a moulded holder to retain cups or containers within the...

Sealing Washer is the fuel injector sealing washer for the Ingenium diesel engine (2.0L and 3.0L AJ20 / AJ21 diesel). It seats at the base of the ...

Front Crankshaft Oil Seal located at the front of the cylinder block, on the crankshaft. Seals the crankshaft where it exits the front of the engi...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit. This seal maintains a gas-tight joint within the EGR section, sealing the connection betwe...

Bolt for the drive belt and pulley assembly on the AJ200 / AJ20 engine family. This fixing secures a pulley or tensioner component at the front of...

Rear Crankshaft Oil Seal for the 2.0L AJ200 engine. This seal fits around the rear of the crankshaft where it exits the cylinder block, retaining ...