Land Rover Defender Parts

24v dsl long belt

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

"Land Rover" Rear Decal Badge A self-adhesive lettered name plate forming part of the exterior rear badging, applied to the rear bodywork. The let...

Fuel Tank Adaptor Ring secures the in-tank fuel pump and sender unit assembly into the aperture on the top of the fuel tank. The ring locks the pu...

Blanking Plug for closing an unused 13 mm (1/2") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Torx Screw - 4.8 × 25mm for use in Land Rover body and trim assemblies. A metric Torx-head screw, 4.8mm diameter × 25mm length, for use where Torx...

Hex Flange Nut - a flanged hexagonal nut used as a general threaded fastener across multiple vehicle assemblies. The integral flange spreads the c...

Oval LAND ROVER Badge - gold lettering on a green background - for the tailgate. This is the classic oval "LAND ROVER" name badge fitted to the ex...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Coolant Expansion Tank Cap - pressurised filler cap for the coolant expansion and overflow container in the engine cooling system. The cap sets th...

Wheel Centre Cap - hub cover for modular steel road wheels. It press-fits into the centre bore of the wheel, covering the hub flange and keeping d...

PCV Valve Service Kit - service parts for the positive crankcase ventilation valve, which sits in the crankcase emission control system on the cyli...

Clip retaining the top of the rear air spring within the rear spring and shock absorber assembly. The clip locates and secures the air spring at i...

Timing Chain Guide - guides the primary timing chain along its run. Maintains correct alignment and tension on the primary timing drive, keeping c...

Timing Chain Guide - guides the timing chain along its run. Maintains correct alignment and tension on the timing drive, keeping crankshaft-to-cam...

Thermostat Tube carries engine coolant between the thermostat housing and the engine on the supercharged 3.0L V6 and 5.0L V8 petrol engines. It run...

Throttle Housing Gasket - seals the throttle body to the intake manifold. Forms the air-tight joint between the electronic throttle housing and th...

Fuel Injector Refit Kit - the seals and retainer required when removing and refitting a fuel injector on 3.0L V6 and 5.0L V8 supercharged petrol en...

Exhaust Manifold Bolt secures the exhaust manifold to the cylinder head. For 3.0L supercharged V6 and 5.0L V8 petrol applications.

Water Outlet Tube carries coolant between the water pump and the thermostat housing within the engine cooling circuit. For 3.0L supercharged V6 an...

Timing Chain Lubricating Oil Jet for the timing drive of the 5.0L V8 petrol engine (AJ133, naturally aspirated and supercharged). The jet feeds pr...

Auxiliary Drive Chain for the AJ133 5.0L V8 and 3.0L V6 supercharged petrol engines. It forms part of the engine's chain drive assembly, running a...

Sealing Ring seals the joint between the engine oil cooler and the water pump on the AJ133 5.0L V8 and 3.0L supercharged V6 petrol engines. It mai...

Oil Cooler Tube forms part of the engine oil cooling circuit, carrying oil between the engine and the oil cooler. Used on 5.0L V8 and 3.0L V6 supe...

O-Ring for the oil pump inlet tube, part of the oil pump, sump and filter assembly. It seals the joint at the oil pump inlet (pick-up) tube, keepi...

Valve Cover Screw and Sleeve from the cylinder head cover fixings of the petrol V8 and supercharged V6 engines. The screw secures the camshaft (va...

Oil Level Sensor - electronic engine oil level sensor mounted in the wall of the sump, forming part of the engine lubrication monitoring circuit. ...

Crankshaft Sprocket Washer from the engine timing drive, fitted at the front of the crankshaft beneath the drive sprocket retaining bolt. It sprea...

Screw, M6 x 38mm, from the timing gear assembly - timing chains, tensioners and guides, and the auxiliary drive. It retains the chain guide in pos...

Lower chain guide for the auxiliary drive chain, part of the timing gear assembly on the 5.0L V8 petrol engine (AJ133). The guide runs against the...

Inlet Valve - cylinder head inlet (induction) valve for the 5.0L V8 AJ133 supercharged petrol engine. The inlet valve admits the intake charge int...

Thermostat Housing for the 5.0-litre AJ133 V8 petrol engine, part of the engine cooling circuit. The housing seats the coolant thermostat and form...

Inlet Manifold Gasket for the left-hand cylinder bank of the 5.0 litre V8 petrol engine (AJ133). It seals the joint between the inlet manifold and ...

Vacuum Pump Seal - sealing ring between the engine-driven vacuum pump and its mounting face on the engine, forming part of the brake servo vacuum c...

Automatic Transmission Fluid (ATF) for the automatic gearbox and power steering circuit. Specified as the transmission and power steering fluid to...

Valve Cover Stud and Sleeve from the cylinder head cover fixings of the petrol V8 and supercharged V6 engines. The stud threads into the cylinder ...

O-Ring for the engine cooling system - it seals the water outlet tube at its connection to the cylinder block, alongside the thermostat housing. T...

Camshaft Cover Gasket - LH seals the left-hand camshaft cover to the cylinder head on the AJ133 5.0L V8 petrol engine. It closes the joint around ...

Valve Spring Retainer from the cylinder head valve train, the top cap that closes off the valve spring. It sits on top of the valve spring and is ...

Tube - Drain

Cylinder Head Bolt secures the cylinder head to the engine block on V6 and V8 petrol engines. Threaded M11 x 178 mm. Twenty bolts are required per...