Land Rover Defender Parts

Pinion Oil Seal sealing the drive pinion shaft where it enters the Salisbury rear differential. Fitted at the nose of the differential housing, th...

Door Vertical Filler for the door sealing trim. This vertical rubber filler closes the gap at the rear edge of the front doors and at the front and...

Master Cylinder

Flanged Nyloc Nut, M10, a multi-purpose locking fastener used across the chassis and suspension. The nylon insert resists loosening under vibratio...

Swivel Joint Washer located within the Swivel Pin Housing Assembly, sealing the interface between the swivel housing flange and the axle beam face....

Kit - Floor Contour Mat

Wiper Drum Adaptor - splined adaptor used in the windscreen wiper system to connect the wiper arm to the splined wiper spindle. The adaptor seats ...

Crankshaft Oil Seal - Front seals the nose of the crankshaft where it passes through the timing cover on the Td5 2.5L 5-cylinder turbo diesel engin...

Panel - Wing - Front

Swivel Pin Housing Kit rebuilds the upper pivot of the front axle swivel housing, where the steering knuckle articulates on the axle. This is the v...

Bolt - Flanged Hex

Clutch Plate - 242mm

Engine Mounting Bracket - 3.5L V8

Oil Seal for the R380 manual gearbox extension case (rear/tail housing). It seals the output shaft where it exits the extension housing, retaining...

Clutch Slave Cylinder for the hydraulic clutch release system on Defender and Discovery 2 models fitted with the R380 manual gearbox. Mounted on t...

Idler Tensioner Pulley for the auxiliary (serpentine) drive belt system. Mounted on the automatic belt tensioner arm, the pulley bears against the ...

Manifold Stud - M8 x 36 mm - for the Td5 2.5L 5-cylinder turbo diesel engine. The stud threads into the cylinder head to locate the manifold flang...

Lamp - Front Flasher

Latch

Cam Cover Bolt for the Td5 2.5L 5-cylinder turbo diesel engine, securing the camshaft cover to the cylinder head. This is the flanged-head bolt th...

Window Clip is a glass retaining clip for the door drop glass. It locates at the base of the sliding window glass in the front and middle doors, s...

Cylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...

Spring - Coil

Stub Axle Oil Seal - Inner

Core Plug for the V8 petrol cylinder block and inlet manifold. The cup-type plug seals the casting core holes left in the coolant jacket after man...

Anti-Roll Bar Bush for the rear suspension. This rubber bush insulates the rear anti-roll bar at its chassis mounting, allowing the bar to rotate u...

Front Door Outer Waist Seal fitted along the upper edge of the front door outer panel, sealing the interface between the outer panel and the door d...

Bar - Torsion

Spire Nut (U-type spire fastener) for trim and panel fixings. Spring-steel push-on nut that clips over a panel edge or stud to provide a captive f...

Nut Plate for the body-side striker mountings, part of the door and tailboard latch assembly. The plate provides captive threaded anchor points be...

Plastic Drive Rivet - Wheel Arch Trim secures exterior trim panels to the body as part of the wheel arch trim fixing set. This one-piece expanding...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Bonnet Hinge Bush for the Land Rover bonnet hinge assembly. This bush fits into the bore of the bonnet hinge, providing a wear surface around the ...

Radius Arm Bush - Front is the flexible mounting bush at the front radius arm-to-chassis location. The radius arm locates the front axle longitudi...

Swivel Pin Kit for the upper front axle swivel assembly, ABS applications. The kit serves the top swivel pin - the pivot interface between the swiv...

Coolant Expansion Tank Cap - pressure cap for the cooling system expansion tank, rated at 15 psi. The cap seals the expansion tank and regulates s...

Bracket - Support

Brake Caliper Bleed Screw - the bleed nipple that threads into the brake caliper. Backing the screw off releases trapped air and old fluid from th...

Door Seal Retainer - Rear End for the rear door seal assembly. This retainer locates and secures the door weatherstrip in its channel along the re...

Radius Arm Bush mounts the front radius arm to the axle within the suspension linkage, at the axle end of the arm. The bush provides a flexible pi...

Rocker Cover Gasket for the Rover V8 petrol engine, sealing the rocker (valve) cover to the cylinder head. The gasket seats between the cover flan...

Exterior Mirror with convex glass and a black finish, supplied as a complete door-mounted mirror assembly. The convex glass gives a wider rearward...

Output Shaft - MT82 6-Speed Manual Gearbox. The output shaft is located at the rear of the MT82 transmission housing and transmits rotational driv...

Washer from the anti-roll bar mounting hardware. It seats beneath the fastener that secures the anti-roll bar (stabiliser bar) to its chassis mount...

Hinge Packer Shim for the door hinge assembly. Fitted between the hinge and its mounting face to set door alignment. Adding or removing shims adju...

Oil Seal Retainer for the front axle swivel housing assembly. This retaining plate holds the swivel housing oil seal square against the chrome swiv...

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...