Land Rover Defender Parts

Washer - M4 flat washer, used to spread the clamping load of an M4 fastener and protect the panel surface beneath the fixing. Fitted at a number o...

Wire - Fuel Injection Valve

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Front seat headrest in Techno trim, forming the upper part of the front seat assembly. The headrest locates on its stems into the guide sleeves se...

Cable Connector is a four-way electrical connector body used in the vehicle wiring harnesses. It joins a harness branch to its mating half, retain...

Centre Silencer for the exhaust system on the 2.4L and 2.2L TDCi (Puma) turbo-diesel. The silencer forms the middle section of the exhaust, sittin...

EGR Valve for the exhaust gas recirculation circuit on Td5 2.5L 5-cylinder turbo diesel and 2.0L L-Series diesel engines. The valve meters a contr...

Coolant Hose - Expansion Tank connects the coolant expansion tank into the engine cooling circuit. It routes coolant between the expansion tank an...

PTO Shaft - Centre - the centre shaft in the power take-off (PTO) drive train. The power take-off transmits rotational drive from the transfer gea...

Fuel Shut-Off Switch for the Td5 diesel fuel system - an inertia-operated safety switch wired into the fuel pump supply circuit. In the event of a...

Gear

Door Lock Assembly - left-hand front door lock and exterior handle assembly, non-slam type. This unit combines the door latch mechanism with the o...

Fuel Pipe - Accumulator To Filter is a formed rigid fuel line in the V8 fuel injection supply circuit. It carries pressurised fuel from the outlet...

Carburettor Needle for the SU variable-venturi carburettor in the fuel system of the 3.5L V8 petrol engine, in twin-carburettor configuration. The...

O-Ring for the air conditioning refrigerant circuit, used at the pipe and hose unions through the system including the condenser and evaporator con...

Locking Nut used to secure the facia moulding. The self-locking nut resists loosening under vibration, retaining the facia panel fixing.

Glazing Rubber - rear side door window lift channel seal for 5mm glass. The rubber lines the window lift channel of the wind-up rear side door, lo...

Heater Cable is the air distribution control cable for the heater assembly. It connects the heater control on the facia to the air distribution fl...

Plastic Clip for the radiator and fan cowl assembly. The clip locates the cowl to the radiator and retains the surrounding cooling system trim, ho...

Blanking Plate for the inlet manifold of the 3.5L V8 twin-carburettor petrol engine. The plate closes off an unused port on the manifold to maintai...

Mud Flap Bracket for the left-hand rear position on High Capacity Pick Up (HCPU) bodywork. Part of the exterior mud flap mounting. The HCPU rear b...

Inlet Manifold forms part of the engine air intake system, distributing the intake charge to the cylinder head inlet ports. Fitted to the 2.5-litr...

Sealing Washer - 18 mm OD x 12 mm ID is a sealing washer with a 12 mm inner diameter and an 18 mm outer diameter, used to seal threaded unions and ...

Power Steering Hose forms part of the power steering hydraulic circuit. It carries hydraulic fluid through the steering assist system, connecting ...

Shim bearing differential 0.062""

Exhaust Clamp a clamp for the exhaust system on 4-cylinder TDi applications. It secures the joint between two exhaust sections, holding the pipes ...

pipe clip 1/2" (12.7mm) for 3/8" (9.5mm) hole

Exhaust Downpipe Bracket for the front section of the exhaust system. Locates and supports the front exhaust downpipe against the engine/chassis, ...

Grommet - moulded rubber grommet for a panel or component aperture. Fitted into a drilled or pressed hole to line the opening, it provides a seal ...

Exhaust Pipe Clamp for the front exhaust pipe joint. Clamps the front exhaust pipe at its connection, holding the joint tight and gas-tight agains...

Female Dovetail for the rear end door latch mechanism. Receives the male dovetail to align and secure the rear door as it closes. Sold individually.

Screw - an M6 x 20 mm pan-head setscrew with a Torx drive, used as a general multi-application fastener. The Torx socket gives positive tool engag...

Turbo Oil Feed Pipe delivers pressurised engine oil to the turbocharger, part of the turbocharger lubrication circuit. Fitted to the 2.2L 16V TDCi...

Front Strut Boot Kit renews the protective gaiter and mounting hardware for a front air suspension strut, part of the four-corner air suspension sy...

Speedometer for the instrument cluster, displaying road speed on non-EFI applications. It mounts in the dashboard instrument panel and is driven b...

Thrust Washer for the LT95 four-speed gearbox, 3.75mm thickness. This selective-thickness washer sets the end-float of the intermediate gear.

Steel Road Wheel - 6.5J x 16, Wolf-style pattern. It provides the mounting surface for a tubeless road tyre and transfers vehicle load from the tyr...

Fuel Pipe - Tap to Tank - a fuel line in the low-pressure diesel supply circuit, running between the fuel tank and the fuel tap. It carries fuel f...

36 Spline Steering Wheel with a black leather rim. It mounts on the 36 spline upper steering column shaft and is retained by the column nut. The s...

Wheelarch - LH is the left-hand plastic wheel arch panel forming the wheel housing on the vehicle body, shielding the surrounding body structure an...

Exterior Rear-View Mirror - door-mounted outer mirror supplied complete with its mounting arm. Mounts to the front door and gives the driver the r...

Filler - Rear Quarter Panel

Pipe Adaptor is a double-male union fitting in the automatic transmission oil cooler circuit. It joins two pipe runs, carrying transmission fluid ...

Needle Valve Kit Float-chamber needle valve and seat for the Zenith Stromberg 175CD carburettor, fitted to the 3.5L V8 petrol engine. The needle v...

Rear Seat Bracket outer right-hand mounting bracket for the rear seating, securing a forward-facing individual rear seat to the floor. Locates the...

Split Pin is a 1.5 mm x 10 mm securing pin used to lock a castellated nut or to retain a clevis pin. It passes through a drilled hole, and its two ...

Door Hinge mounts the front door to the body at the A-post, carrying the door's weight and setting its swing and closing alignment. This is the upp...