Land Rover Defender Parts

Door Speaker An original-fit speaker for the in-car audio system. It reproduces the audio output of the radio/head unit through the vehicle's spea...

Exhaust Downpipe - the front section of the exhaust system, connecting the turbocharger outlet to the intermediate exhaust pipe. Fitted to the 2.4...

Locking Wheel Nut for replacing one standard wheel nut per wheel as a theft deterrent. The locking wheel nut features a unique external drive prof...

Rotor Arm for the 24V shielded ignition distributor. The rotor arm mounts on the top of the distributor shaft and, as it rotates, routes the high-t...

Clevis Pin for the differential lock selector linkage in the LT230 transfer gearbox. This clevis pin secures the selector lever pivot that actuate...

Gearchange Roll Pin - a tension (roll) pin used in the manual gearchange mechanism to secure the gear lever to the selector shaft. Applies to the ...

Steering Hose forms part of the power steering hydraulic circuit. It carries pressurised hydraulic fluid between the power steering pump and the s...

Packing Strip fitted between the bulkhead base and the footrest bracket mounting on the chassis of Defender 90/110. This strip provides the correc...

Exhaust U-Bolt secures a joint in the front section of the exhaust system. The U-bolt clamps over the pipe at a slip joint and, tightened against i...

Decal is an exterior body decal applied to the rear of the vehicle. It carries the Land Rover name in silver lettering on a black background, and ...

Fastener - black plastic drive-type (fir tree) push-in fastener used throughout the vehicle to secure body trim panels, interior linings, underbonn...

Heater Controls Spacer - spacer fitted within the heater control assembly of the HVAC unit. Sold individually.

Bonnet Stop Buffer is a rubber buffer that cushions the bonnet where it rests against the body when closed. Mounted on the front bodywork, it supp...

Cylinder Head Dowel - Plastic is a locating pin fitted at the mating face between the cylinder block and cylinder head in the Td5 2.5L 5-cylinder t...

Torx Screw - 4.8 × 25mm for use in Land Rover body and trim assemblies. A metric Torx-head screw, 4.8mm diameter × 25mm length, for use where Torx...

Clevis pin

Front Cover Gasket for the LT85 five-speed manual gearbox, G20C unit. This gasket seals the front cover to the main gearbox casing, preventing oil...

Flywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...

Cylinder Liner - the replaceable liner that forms the bore in which the piston and rings run within the cylinder block. It provides the hard weari...

Splash Seal

Bolt - Lower Steering Shaft UJ is the M8 x 35 mm clamp bolt that secures the universal joint at the lower steering shaft, within the steering colum...

Self-Tapping Screw, No.6 x 3/8". A self-tapping fastener that forms its own thread as it is driven, used to secure body panels, trim and light fix...

Rear Fog Switch for the dashboard switching circuit. A push-push type switch that controls activation of the rear fog lamp circuit. Mounts in the ...

Radiator Hose - the top hose of the engine cooling circuit, connecting the cylinder head outlet to the top of the radiator. It carries heated cool...

Heater Control Pin

Filler and Level Plug for the V8 4-speed gearbox and for differential assemblies across a wide range of classic Land Rover models. Fitted at the s...

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...

Bump Stop for the suspension, mounted at the limit of axle travel. This rubber stop caps upward suspension movement at full compression, providing...

Sedimentor O-Ring for the diesel fuel filter assembly. This rubber sealing ring seals the sedimentor bowl against the filter head, preventing fuel...

Cab Mounting Stud

Interior Lamp Lens for the interior courtesy lamp. The translucent lens clips over the lamp body, protecting the bulb and diffusing its light into...

Washer

Special Bolt with a coarse ACME-form thread, 1/4 in diameter and 5/8 in long. It is a body fixing used to secure inner-wing mudshields, floor plat...

Distance piece

Swivel Pin Retaining Bolt A fixing bolt for the front axle swivel pin housing. It secures a swivel pin to the swivel pin housing, retaining the pi...

Engine Stud for the Rover V8 petrol engine, measuring 5/16" x 2-1/8" with a UNC/UNF dual thread form. The coarse UNC end threads into the engine c...

Sealing Washer is a copper joint washer used in multiple engine and ancillary applications across the Land Rover range, including as a sealing wash...

Hose Clip for securing flexible hoses to pipes and stubs throughout the Land Rover. Tightening the clip compresses the hose onto the stub to form a...

Propshaft Washer for the front propshaft flange connection. The washer sits at the bolted joint between the front propshaft and its mating flange,...

Key Wheel Nut

Blanking Plug - timing chain cover, supplied with its O-ring. Seals a machined service aperture in the timing chain cover of the Ingenium engine f...

Coolant Expansion Tank Cap - pressurised filler cap for the coolant expansion and overflow container in the engine cooling system. The cap sets th...

Oil Filter Element for the 3.0L AJ20 / AJ22 Ingenium six-cylinder engine, fitted in the engine lubrication circuit. The cartridge element seats in...

Wheel Centre Cap - hub cover for modular steel road wheels. It press-fits into the centre bore of the wheel, covering the hub flange and keeping d...

Washer Reservoir Cap for the windscreen washer fluid reservoir. Seals the filler neck of the washer bottle in the wash/wipe system, retaining wash...

Magnetic Oil Drain Plug for the engine oil sump on the 2.0L Ingenium (AJ200/AJ20) four-cylinder petrol and diesel engines. The plug seals the drai...

Mudflap