Land Rover Defender Parts

Bonnet Buffer is a resilient rubber cushion that forms part of the bonnet closure assembly at the front of the body. It provides the stop the bonn...

LED Lamp Upgrade Kit: 73mm LED lamp units that replace the original bulb-type lamp units.

Steering Relay Gasket seals the steering relay assembly within the steering linkage. The steering relay transfers movement from the steering box d...

Drive Member - 10-Spline is the drive coupling at the outer end of the axle, forming part of the wheel hub and drive assembly. Its 10-spline inter...

Gearbox Bearing is the ball bearing that supports the primary pinion, or first motion shaft, in the main gearbox. Located at the front of the gear...

Gaiter Retainer - secures the rubber gaiter around the high-low (transfer) lever on the LT76 gearbox, which carries an integral transfer box. The ...

O-Ring Seal - sealing ring for the steering box rocker shaft. Fitted around the rocker (sector) shaft where it passes through the steering box hou...

Camshaft Cover Gasket seals the camshaft cover plate to the cylinder block, forming part of the camshaft housing and engine lubrication boundary. ...

Bolt for the LT76 gearbox assembly, with a 5/16" BSF (British Standard Fine) thread. Used as a threaded fastener within the gearbox casing.

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Universal Joint for the propeller shaft, of the 82mm cap-to-cap type. The universal (cardan) joint connects two sections of the propshaft, transmi...

Lucar Connector - a fully insulated two-way in-line electrical connector for joining wiring within the loom. Of the Lucar (blade) terminal type, i...

Rear Crankshaft Packing Strip (T-Piece) forms part of the rear crankshaft oil seal arrangement at the back of the cylinder block. The T-piece pack...

Inlet Valve - the poppet valve that seals the inlet port in the cylinder head and opens on the induction stroke to admit the incoming air charge to...

Front Bumper in galvanised steel, mounting across the front of the chassis frame. It bolts to the front chassis dumb-irons to provide front-end im...

Cylinder Head Bolt - a clamping bolt securing the cylinder head to the engine block. It draws the head down onto the block to compress the head ga...

Rear Propshaft for the short-wheelbase chassis, forming part of the driveline between the transfer gearbox and the rear axle. The propshaft transm...

Shock Absorber for the front suspension, a heavy-duty oil-filled hydraulic damper. Mounted between the axle and the chassis, it damps the oscillat...

Rotor Arm for the Lucas distributor in the ignition system of the 2.0L and 2.25L 4-cylinder petrol engines (up to engine suffix C). Driven by the ...

Propshaft UJ Circlip - a retaining clip for the universal joint of the propeller shaft. It seats in the groove of the yoke ear and holds the beari...

Glass Fuse - 25A - a 25 A glass cartridge fuse for the vehicle's electrical circuits. The glass body carries a calibrated wire element between two...

Exhaust Valve - the poppet valve that seals the exhaust port in the cylinder head and opens on the exhaust stroke to release spent combustion gases...

Primary Pinion Bearing for the manual gearbox, supporting the primary pinion (gearbox input shaft). The primary pinion transmits drive from the cl...

Transfer Box Intermediate Shaft Shim, 0.005in thick, used in the transfer box to set the end float of the intermediate gear on its shaft. Selectiv...

Hot Plug - 2.0L & 2.25L Diesel

Steel ball 1/4"

Swivel Pin Housing Locking Plate mounts to the front axle swivel pin housing. It locks the swivel pin in position and provides the fixed stop that...

Manifold Stud - a mounting stud for the manifold. Threaded into the cylinder head, it locates the manifold and clamps it to the head face via its ...

Front Towing Eye / Lifting Ring bolts to the front of the chassis, providing an anchored attachment point for towing, recovery and lifting. The ri...

Double-Grooved Ball Bearing for the manual gearbox and transfer box. It supports and locates a rotating shaft within the casing, carrying the radia...

Bulb 24V 21/5W dual-filament bulb for 24-volt electrical systems. The 21W filament serves the stop light circuit and the 5W filament serves the tai...

Universal Joint is a cross-type (spider) joint fitted within the propshaft assembly, transmitting rotational drive between opposing yokes while acc...

Breather Set Screw secures the breather to the rocker cover within the engine crankcase ventilation arrangement. It retains the breather against t...

Oil Gallery Plug for the cylinder block oil gallery on Land Rover 4-cylinder engines. The oil gallery is the network of internal drillings in the ...

Upgrade your Land Rover Defender (1987-2006, 2007-2016) or Series 3 with the WIPAC LED 73mm smoked lamp kit. Smoked LED style light for a sleek...

Starter Switch for Land Rover Series 1 and Series 2 models (1948-1966). This switch activates the starter solenoid to engage the starter motor whe...

Hex Nut with a 5/16" UNF (Unified National Fine) thread. This six-sided fastener threads onto a matching 5/16" UNF bolt or stud and is tightened w...

Static Lap Seat Belt for the second-row seating position, forming part of the interior occupant restraint system. The non-retractable, fixed-lengt...

Clutch Slave Cylinder Bleed Screw for the hydraulic clutch release circuit. It threads into the clutch slave cylinder, at the highest point of the ...

Exhaust Silencer for right-hand-drive applications. Part of the exhaust system, this silencer attenuates combustion noise as the gases pass throug...

Copper Washer is a soft sealing washer used to form a leak-tight metal seal at a threaded or banjo union. Positioned between a bolt or fitting and...

In/out member spring

Barrel Lock and Key for the door lock, supplied as the keyed lock barrel together with a matching key. The barrel is the cylinder the key turns to...

Timing Chain Idler Wheel runs against the timing chain within the front timing case, guiding the chain and helping maintain its tension between the...

Drain Plug for the axle casing and fuel tank. This brass threaded plug seals the drain aperture at the bottom of the differential and axle casing,...

Clevis Pin - pivot pin used in the mechanical brake and transmission linkages. It passes through a forked clevis and the eye of a mating rod or lev...

Leather hasp civilian

Transfer Box Lever Lock Nut used to secure the selector linkage at the transfer case. This half nut (thin profile locking nut) threads onto the sel...