Land Rover Defender Parts

Chain - Timing

Brake Disc & Caliper Bolt - a fixing bolt for the brake disc and caliper assembly. It is used at both the front and rear brake disc and calipe...

Ignition Switch is the steering column ignition switch. Mounted on the steering column, it controls the ignition and starter circuits when operate...

Front Seat Covers - a tailored waterproof cover set for the pair of front seats, in grey. The covers are made from waterproof woven polyester with...

Bush Kit - Front - From VIN 2A626646

Transfer Box

Rear Door Casing - the interior trim panel that lines the inner face of the rear end door. It covers the door's inner structure to give a finished...

Centre Cubby Box - Techno finish. A console box that mounts on the transmission tunnel between the front seats, providing enclosed central storage ...

Turbocharger Circlip - retaining clip for the turbocharger actuator on diesel turbocharger installations. It secures the actuator rod to the contr...

Differential Assembly Bolt for the axle differential. It secures components of the differential assembly, clamping them to the specified torque du...

Flanged Nut - M6 captive nut, also described as a U-nut or speed clip, used to provide a threaded fixing point in sheet metal and moulded panels. ...

Sound Deadening Panel reduces road, transmission and drivetrain noise transmitted through the floor into the cabin. The self-adhesive damping pane...

O-Ring seals the variable valve timing (VVT) solenoid within the timing gear and sprocket assembly. It maintains an oil-tight joint between the VV...

Stud used in the rear body upper fixings. The stud provides the threaded shank at the upper mounting points where the rear body ties into the vehi...

Key blank for the door lock barrels and the cubby box barrel lock. Supplied uncut - the blade carries the correct key section for these barrels, bu...

Exhaust Gasket for the flanged joint between the exhaust front pipe and the catalyst section. It seals the bolted flange where the front pipe meet...

Lower Door Panel Assembly

Exhaust Gas Temperature Sensor for the lower sensing position at the diesel particulate filter, within the exhaust aftertreatment system. The sens...

Inlet Manifold Gasket - 5.0 V8 - RH seals the inlet manifold to the cylinder head on the right-hand bank of the 5.0 litre V8 petrol (AJ133) engine,...

Rear Shock Absorber - hydraulic damper for the rear suspension of the short-wheelbase (90-inch) chassis. It controls the oscillation of the rear co...

Transmission Brake Backplate - the mounting plate for the drum-type transmission parking brake on the rear output of the LT230 transfer box. The b...

Brake Disc & Caliper Bolt - a fixing bolt for the brake disc and caliper assembly. It is used at both the front and rear brake disc and calipe...

Gasket - Oil Filter to Block seals the joint between the oil filter housing and the cylinder block, within the Oil Cooler and Filter assembly. It ...

Spark Plug Aperture Gasket for the right-hand camshaft cover, sealing the spark plug well against oil ingress. The camshaft cover carries a tube f...

Coil Spring is a heavy-duty rear suspension coil spring that raises ride height by approximately 40mm (1.5 inch) over standard. It is rated to car...

Hex-Head Bolt for the engine timing gear cover and oil pan. Threaded fastener that secures the timing gear cover and oil pan assembly on Duratorq-...

Flange Bolt that secures the rear output drive flange to the transfer box output shaft. It clamps the propshaft drive flange onto the transfer box...

O-Ring for the oil pump inlet tube, part of the oil pump, sump and filter assembly. It seals the joint at the oil pump inlet (pick-up) tube, keepi...

Front Wheel Bearing Kit containing the parts needed to overhaul one front hub bearing assembly. The taper roller bearings carry the front hub on th...

Gasket - Oil Filter to Block seals the joint between the oil filter housing and the cylinder block, within the Oil Cooler and Filter assembly. It ...

Front Mudflap Brackets - Black - a pair of stainless steel brackets in a black finish that carry the front mud flaps at the rear of the front wheel...

Fuel Pressure Sensor for the high-pressure fuel injection circuit on petrol engines. It measures fuel rail pressure and temperature and reports to ...

Inlet Manifold Gasket - 5.0 V8 - RH seals the inlet manifold to the cylinder head on the right-hand bank of the 5.0 litre V8 petrol (AJ133) engine,...

Thermostat Housing - engine cooling circuit component for the 3.0L Ingenium six-cylinder petrol engine (AJ20P6 / AJ22P6). The housing carries the ...

Hose - Connecting

Oil Pump Inlet Tube Assembly for the engine lubrication system. The inlet tube draws oil from the sump and feeds it to the oil pump inlet, forming...

Front Brake Pad Kit - friction pad set for the front disc brake assembly, for the 380 mm front disc and size 20 caliper configuration. The pads lo...

Hex Nut - narrow-pattern hexagon nut used in the steering linkage, at the track rod and steering damper fixings. Two are used per vehicle. Steerin...

Exhaust Gas Temperature Sensor located at the turbocharger. It measures the exhaust gas temperature entering the turbine and aftertreatment stage a...

Blanking Plug used within the engine cooling system - thermostat housing, radiator and coolant expansion tank, and the cooling pipework. The plug ...

Expansion Tank Seal - sealing ring for the bleed valve fitted to the coolant expansion tank in the engine cooling system. Seals the bleed valve in...

Differential Gear Kit for the LT230 transfer box centre differential. The centre differential splits drive between the front and rear output shaft...

Handbrake cable from the handbrake actuation assembly, linking the handbrake lever to the transmission brake mounted on the transfer box rear outpu...

Front Anti-Roll Bar Bracket - mounting bracket that secures the front anti-roll bar to the chassis frame. It clamps over the anti-roll bar bush an...

Drive Fastener - black plastic drive-in retaining clip used to secure body mouldings, trim panels and interior finishers to their mounting panels. ...

Kick Panels - moulded interior trim panels for the footwell area, supplied as a pair. The panels fit against the lower bulkhead on either side of ...