Land Rover Defender Parts

Stop Bumper is a moulded rubber bump stop mounted to the rear of the chassis on the left-hand side. It cushions contact between the rear axle and ...

Door Bottom Repair Section - a weld-in repair panel for the lower section of the Defender door frame, the area most prone to rust and corrosion. I...

Steering Arm Fixing Kit for the heavy-duty steering arms DA5503 and DA5504. It supplies the fixings needed to mount the heavy-duty steering arms i...

Rear Wing Protector - protective panel fitted over the top edge of the rear wing to shield the paintwork and panel surface from scuffs, scratches a...

Waterproof Seat Cover Set - front seat covers finished in black, forming part of the vehicle's interior protection. The covers are made from water...

Timing Belt Kit for the 2.5L naturally aspirated diesel and 2.5L turbo diesel engines. It serves the timing belt drive that keeps the crankshaft, c...

Door Bolt Kit - a stainless steel fixing set for the four side doors (Puma applications). The kit covers both the front and rear side doors. Stain...

Hose Clip - Jubilee - 70-92mm is a worm-drive band clamp with a clamping range of 70-92 mm. It secures a hose over its spigot or connector, compre...

Bonnet Buffer Defender 2007 on

Rear Mudflap Replacement - 90 TD5 - RH

Headlamp Bulb - a 24V dual-filament bulb for the main headlamp, rated 55/50W with a P45T base. The two filaments carry the main and dipped beam wi...

Demister Outlet Finisher - vent finisher set into the top of the dashboard over the windscreen demister outlet, directing heated and ventilated air...

Radiator with Integrated Oil Cooler - the main engine cooling radiator for the 200 TDi diesel engine, incorporating a built-in engine oil cooler an...

Radius Arm Bolt, 1/2" UNF, 5-3/4" long, securing the radius arm to its chassis mounting bracket. The radius arms locate the front axle fore and af...

High-Tensile Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/4" shank length. A hex-head fastener manufactured to a high-t...

Bolt - V8 Inlet Manifold is the fastener that secures the inlet manifold on the Rover V8 petrol engine. It clamps the inlet manifold to the cylind...

Bolt 1/4" UNC x 1-1/4" is a coolant pump fixing bolt used on the 3.5L V8 petrol engine. It secures the coolant (water) pump to the engine within t...

Bolt - M8 x 100mm hex head bolt used in the transmission mounting assembly. Secures transmission mounting components on Series III vehicles equipp...

Door Filler - Top - Front is the horizontal filler strip that runs along the top edge of the front door frame. It closes the channel at the top of...

Alloy Gear & Transfer Box Knobs Machined alloy replacement knobs for the main gear lever and the transfer box lever, supplied as a matching pai...

Sill Protector in aluminium chequer plate, guarding the sill panel below the doors. Fits along the sill to shield the panel from stone chips, scuf...

Air Intake Grille is the louvred wing-top panel that covers the cold-air inlet at the base of the windscreen. Mounted on the left-hand wing top, i...

Bonnet Release Cable is the Bowden control cable that links the in-cab release lever to the bonnet latch mechanism. Pulling the release lever draw...

Steel Road Wheel is a welded steel road wheel with a 6.5 x 16 inch rim, finished in black with a Wolf-style profile for road use with tubeless tyre...

Rod LHD

Fuel Tank Sender mounts in the fuel tank and signals the fuel level to the dashboard gauge, forming part of the fuel level sensing circuit. A floa...

Seatbase Storage Lid closes the storage locker built into the seat base. This lid fits over the stowage compartment within the seat base, providin...

Spire Nut - No. 10 U-Type for use in dashboard and body panel fixings on Land Rover Defender and Discovery I. This U-type spire nut clips onto she...

grommet washerpump to reservoir

Interior Trim Fastener - a grey drive-in fastener for securing interior trim panels in the cabin. It retains facia and carpet trim, the cubby box,...

Restore and reinforce your Land Rover's rear floor structure with this galvanised body crossmember floor, designed for Defender and Series 2, 2A, a...

Steering Box Output Oil Seal for the manual, non-power-assisted steering box. It seals the output (rocker) shaft where it exits the steering box h...

Headlamp Screw is a fastener used in the front headlamp assembly. It secures the headlamp unit and rim within their mounting, holding the lamp in ...

Camshaft Lock Washer retains the camshaft gear securing bolt at the front of the camshaft, part of the engine timing drive. After the bolt is tigh...

Exhaust Clamp for the V8 engine exhaust system, securing a front-pipe joint. The clamp draws two pipe sections together at their slip joint, holdin...

Nylon Stud, a trim retaining fastener used to hold interior trim panels and carpet in position. The stud pushes into a pilot hole in the body pane...

WAVE POWER SM 5W-40 is a universal high performance fuel saving oil based on 100% synthetic technology for use in gasoline- and diesel engines of p...

Clutch Slave Cylinder Bleed Screw for the hydraulic clutch release circuit. It threads into the clutch slave cylinder, at the highest point of the ...

Bearing used across several Land Rover drivetrain assemblies: the LT230 transfer box, where it supports the high and low range gear; the LT95 gearb...

Magnetic Drain Plug for the engine oil sump and the LT230 transfer box drain ports. The magnetised tip captures ferrous wear particles suspended i...

Bracket tie bar for steering box

Clutch Pipe - Classic

Exhaust Silencer for right-hand-drive applications. Part of the exhaust system, this silencer attenuates combustion noise as the gases pass throug...

Spiralox Ring is the spiral-wound retaining ring that secures the front half shaft at the drive shaft and hub of the front axle. Seated in a machi...

Crankshaft Thrust Washer controls crankshaft end-float - the axial movement of the crankshaft within the block - at the centre main bearing. The w...

Copper Washer is a soft sealing washer used to form a leak-tight metal seal at a threaded or banjo union. Positioned between a bolt or fitting and...

In/out member spring

Heater Duct, right-hand side, within the heater demister and air distribution system. Channels air from the heater assembly to the windscreen demi...