Land Rover Defender Parts

Outer Distance Piece for the front axle swivel pin housing. The distance piece is a spacer that sets the position of the swivel pin bearing within...

Bracket

Bulb Holder Assembly - Blue for the instrument panel illumination circuit. This holder and bulb assembly fits within the instrument cluster to pro...

Instrument Panel Dash Mounting for the instrument binnacle assembly. This structural mounting bracket secures the instrument panel within the dash...

Piston Ring Set - Standard - 2.25/2.5 Diesel

Front Sill Panel for the left-hand side of the body, the outer panel running along the lower bodyside below the front door aperture. The sill clos...

Main Bearing Set - crankshaft main bearing shells for the 2.25L four-cylinder three-bearing engine. The main bearings support the crankshaft withi...

Facia Panel Assembly - LHD is the end closing trim for the upper dashboard fascia on left-hand drive Defender 90 and 110, finished in black. This ...

Wing Fixing Plate is a three-stud captive stud plate used in the front body mounting assembly, where it secures the front wing to the radiator (fro...

Past op 110 TD5 v.a. 1999 plastic tank achterin en Puma TDCI

Upgrade your Land Rover Defender 90 & 110 (2002-2016) with this OEM-style Safari rear door, designed with pre-drilled spare wheel carrier holes...

Rear Fog Lamp - LED, 95mm round, clear lens, for North American Specification (NAS) Defenders. The lamp fits the standard 95mm round rear fog lamp...

Body blanking plug 12 X 18MM

Propshaft Spacer Kit (25mm) - a driveline spacer fitted between the propshaft flange and the transfer box or differential flange to restore the pro...

Diesel Injector for the fuel injection system, delivering metered, atomised fuel from the injection pump into the engine. Fitted to the 2.25L and ...

Leather hasp civilian

Fits Land Rover Defender models (2007-2016) Clear lens wit orange bulb designed for a sleek, modern look

Propshaft Gaiter (Sliding Joint) is the flexible rubber boot that seals the sliding splined joint of the propshaft in the drivetrain. The sliding ...

Screw is a fastener used in cooling and heating system assemblies on Land Rover vehicles.

M12 Nut used as a fastener at several chassis and running-gear locations, including the swivel pin housing, drive shaft fixings and front brake cal...

A-Post Trim is the interior trim panel that covers the A-pillar (the windscreen pillar), concealing the body structure and any wiring routed throug...

Air Duct Seal - seals the heater air duct against the parcel tray within the HVAC air distribution. For vehicles without air conditioning.

Fuel Connector Block for the Td5 2.5L 5-cylinder turbo diesel engine (Euro III, later specification). The block is the central junction of the fuel...

Crankshaft Pulley mounts on the front of the crankshaft on the 200TDi 2.5L turbo diesel engine and drives the auxiliary drive belts. This pulley i...

Bolt with a 1/4" UNF (Unified Fine) thread. A threaded steel fastener used to secure body panels and ancillary fittings.

Door Clevis Pin for the door check strap mechanism. The pin locates the check strap to its mounting bracket, forming the pivot the strap works aga...

Safari Door Bolt Kit - a stainless steel fixing set for the rear safari (third) door, for Non-Puma applications. The bolts secure the fixings of t...

Mounting assy Defender 7A752070 to BA407819

Fuel Pump & Sender - in-tank low-pressure fuel pump and fuel level sender assembly for the Td5 2.5L 5-cylinder turbo diesel. The unit mounts v...

Pillar seal

Brake Caliper for the left-hand front wheel, part of the front disc brake assembly in the hydraulic braking circuit. The caliper houses the piston...

Brake Caliper for the right-hand front wheel, part of the front disc brake assembly in the hydraulic braking circuit. The caliper houses the pisto...

Bolt 5/16" UNC x 5" is a long mounting bolt for the coolant pump and power steering pump on the 3.5L V8 petrol engine. Its length carries the powe...

Window Channel top run channel for the front door glass, fitted within the door frame aperture. The channel lines the upper edge of the window ope...

Oil Pump Chain Kit for the Td5 2.5L 5-cylinder turbo diesel, part of the oil pump drive in the engine's lubrication system. The oil pump is driven...

Brake Pad Set - Rear - a set of friction pads for the rear disc brakes, forming part of the rear braking assembly. The pads locate in the rear bra...

Front Coil Spring - Medium Duty, +2" Lift (Terrafirma). These front coil springs raise ride height by approximately 2 inches over standard and are...

Changeover Relay - 5-Pin - Green is a standard 5-pin changeover relay used across multiple electrical circuits. This relay is used in various appl...

Rear Fog Lamp Switch is the dashboard-mounted push-button control for the rear fog lamp circuit. This switch allows the driver to activate the rea...

Cable Gaiter - Door Wiring is a protective sleeve and grommet fitted at the door aperture of the Defender body, routing the door wiring harness saf...

LED Side Repeater is an amber side repeater lamp within the exterior signalling circuit, mounted in the front wing aperture. Each lamp provides la...

Inertia Switch in the fuel supply and engine electrical circuit. It cuts electrical power to the fuel pump on a sudden impact or severe deceleratio...

Spring Washer for use as a locking fastener component across Land Rover assemblies. A helical split spring washer providing resistance against fas...

Water-in-Fuel Sensor for the Td5 2.5L 5-cylinder turbo diesel fuel filter / sedimentor assembly. It threads into the base of the fuel filter housi...

Fuel Tank Cradle from the rear fuel tank mounting - the steel support frame that carries the classic-pattern plastic fuel tank beneath the chassis....

Clutch Control Valve is fitted in the hydraulic clutch release circuit between the master cylinder and the concentric slave cylinder. It regulates...

Heater Blower Motor for the heater and ventilation assembly. Drives the blower fan that draws air across the heater matrix and distributes it throu...

Clutch Cover is the pressure plate assembly of the clutch, bolting to the engine flywheel within the clutch and gearbox coupling. Its diaphragm sp...