for Discounts / VAT
for Discounts & Correct VAT
Land Rover Freelander parts for both generations. The L314 (1997 to 2006) and L359 (2006 to 2014) use different platforms, engines, and drivetrains. OEM, Genuine, and aftermarket components in stock. Select your generation below to find correctly fitted parts for your vehicle.
Oxygen Sensor – Pre-Catalyst for the 1.8L K Series petrol engine, fitted in the exhaust upstream of the catalytic converter. This upstream lambda ...
View full detailsWasher - 22 mm OD x 12 mm ID is a washer with a 12 mm inner diameter and a 22 mm outer diameter, fitted within the 1.8 L K-Series petrol engine ass...
View full detailsRocker Cover Gasket for the 2.0L L-Series diesel engine, sealing the rocker cover to the cylinder head. The gasket forms the oil-tight seal along ...
View full detailsUpper Sump Gasket for the 2.0L Td4 diesel engine, forming the oil-tight joint between the upper sump and the base of the cylinder block. The Td4 u...
View full detailsRoof Aerial Base is the roof-mounted mounting and connection base for the radio antenna. It secures the aerial mast to the roof panel, seals the m...
View full detailsAir Conditioning Condenser - part of the air conditioning refrigerant circuit, mounted at the front of the vehicle in the airflow path ahead of the...
View full detailsFog Lamp Bezel - the trim ring that surrounds the front fog lamp aperture in the front bumper, finishing the opening and locating the fog lamp with...
View full detailsFog Lamp Bezel - the trim ring that surrounds the front fog lamp aperture in the front bumper, finishing the opening and locating the fog lamp with...
View full detailsGas Strut - Tailgate Gas-charged support strut for the rear tailgate. The strut mounts between the body aperture and the inner tailgate, using com...
View full detailsWindscreen Washer Jet - spray nozzle in the windscreen washer system. Fed by the washer pump, the jet directs washer fluid onto the windscreen to ...
View full detailsBlock
Wiper Blade - Front is the driver-side front windscreen wiper blade, 22 inches long, for right-hand drive (RHD) applications. It clips to the fron...
View full detailsCamshaft Position Sensor monitors the rotational position of the camshaft and reports it to the engine ECU. The ECU uses this signal to identify c...
View full detailsTiming Belt Tensioner - rear tensioner assembly for the 2.0L L-Series diesel engine. Maintains correct tension on the timing belt, holding it firm...
View full detailsUpper Engine Tie Rod within the engine mounting system. It links the upper part of the engine to the body structure, reacting engine torque and re...
View full detailsTow Hitch for the towing system, rated to a maximum gross towing weight of 3,500 kg. The hitch bolts to the tow bar and carries the tow ball, prov...
View full detailsGlovebox Lamp Assembly is the interior illumination lamp that lights the glove box compartment, forming part of the vehicle's interior lighting cir...
View full detailsTrack Rod Adjuster forms the threaded, adjustable joint in the steering track rod, allowing the effective rod length to be set. It sits within the...
View full detailsDrive Shaft - Assembly
Bonnet Assembly - the hinged body panel that closes over the engine compartment, forming part of the front body structure. It pivots on the bonnet...
View full detailsLocking Wheel Nut Set - anti-theft security for the road wheels. Replaces standard wheel nuts with keyed locking nuts that can only be removed usi...
View full detailsHD Rear Bumper
Air filter element Freelander TD4
Kit - Clutch
Auxiliary Drive Belt for the 1.8L K-Series four-cylinder petrol engine, driving the alternator. The belt runs from the crankshaft pulley to the al...
View full detailsEGR Bypass Tube is a blanking component for the exhaust gas recirculation (EGR) circuit on the 2.0L Td4 diesel engine. Fitted in place of the orig...
View full detailsCamshaft Seal - Rear
Brake Hose flexible hose for the front right-hand hydraulic braking circuit. Connects the fixed rigid brake pipe to the front right-hand brake cal...
View full detailsClutch Kit for the TD4 2.0L diesel (M47), manual transmission. Lead-free. The kit contains the clutch cover (pressure plate) and the driven plate....
View full detailsCylinder Head Bolt for the 2.0L 8-valve L-series 4-cylinder diesel engine. The bolt clamps the cylinder head to the cylinder block, holding the he...
View full detailsTailgate Glass is the glazing panel for the rear tail door, forming the fixed rear window of the tailgate assembly. The panel bonds into the rear ...
View full detailsExhaust Mounting Rubber Insulator fitted within the exhaust system support assembly to suspend and isolate exhaust pipe sections from the vehicle b...
View full detailsCoolant Bleed Hose for the engine cooling system's expansion tank circuit. This hose carries coolant and vented air between the expansion tank and...
View full detailsTappet Hydraulic
Side Steps are an exterior bolt-on accessory fitted along the lower body beneath the door openings. They provide a raised tread to ease entry and ...
View full detailsSingle-Pole Bulb Holder for the rear lamp cluster, carrying a single-filament (single-contact) bulb within the combination lamp housing. Mounts in...
View full detailsClutch Master Cylinder - the hydraulic cylinder in the clutch actuation circuit. Linked to the clutch pedal, it converts pedal effort into hydraul...
View full detailsEngine Tie Rod is the lower torque reaction rod that locates the engine and transmission, controlling powertrain movement and transmitting torque r...
View full detailsIntermediate Exhaust Pipe for the 2.5-litre KV6 petrol engine, forming the centre section of the exhaust system. It connects the front downpipe to...
View full detailsRear ABS wheel speed sensor, part of the anti-lock braking system's wheel speed sensing circuit. Catalogued under a sensor kit part number; the ass...
View full detailsABS Sensor Kit - Front
Handbrake Cable - Right-Hand for the parking brake system. The cable runs rearward from the handbrake lever mechanism to the right-hand rear brake...
View full detailsBrake Servo - vacuum brake booster mounted on the bulkhead between the brake pedal and the brake master cylinder. Vacuum is applied to one side of...
View full detailsBrake Hose - Front Flexible Jump flexible hose for the front hydraulic braking circuit. This jump hose connects the body-mounted rigid brake pipe ...
View full detailsBrake Caliper - Front - Left-Hand is part of the front disc brake assembly on the Freelander 1. The caliper houses the hydraulic pistons and brake...
View full detailsBrake Caliper - Front - Right-Hand is part of the front disc brake assembly on the Freelander 1. The caliper houses the hydraulic pistons and brak...
View full detailsRear Brake Drum for the rear drum brake assembly. The drum locates on the rear hub and provides the machined friction surface that the brake shoes ...
View full detailsFront Brake Disc - vented, 277 mm diameter. Part of the front brake discs and calipers assembly. The disc mounts to the front hub flange and provi...
View full details1997 to 2006. K-series, KV6, L-series, and TD4 (BMW M47R) engines.
Freelander 1 parts →2006 to 2014. eD4, TD4, and SD4 diesel variants plus 3.2 petrol.
Freelander 2 parts →The Land Rover Freelander ran across two distinct generations and was discontinued in 2014. Each generation uses different platforms, engines, and drivetrains. Parts are not interchangeable between them, and fitment must be confirmed by generation, model year, and engine type before ordering.
The Freelander 1 (L314) was produced from 1997 to 2006 in 3-door and 5-door body styles. Engine options included the 1.8-litre Rover K-series petrol, the 2.5-litre KV6 V6 petrol, the early 2.0-litre Rover L-series diesel (1997 to 2000), and the 2.0-litre BMW M47R TD4 diesel (2001 to 2006). It used a monocoque structure with a viscous coupling unit and intermediate reduction drive, with no low-range transfer case. The Freelander 1 sold over 540,000 units across Europe during its nine-year production run, making it the best-selling four-wheel drive vehicle in Europe for five consecutive years after its 1997 launch.
The Freelander 2 (L359) was produced from 2006 to 2014 as a 5-door estate only. It is based on the Ford EUCD platform and shares its architecture with the Volvo XC60. Diesel engines used the 2.2-litre PSA DW12 unit in three states of tune: eD4 (150 hp, front-wheel drive from 2011), TD4 (160 hp), and SD4 (190 hp). Petrol options included the 3.2-litre Volvo B6324S5 inline six and, in later markets, a 2.0-litre Ford EcoBoost petrol. Four-wheel drive models use an active Haldex coupling system. Production ended in October 2014. The Freelander 2 was succeeded by the Discovery Sport.
Vehicle IdentificationIf you are unsure which generation you own, the quickest method is to check the vehicle's production year. Vehicles produced up to and including 2006 are Freelander 1 (L314). Vehicles produced from late 2006 onward are Freelander 2 (L359). The VIN plate is located on the door sill or the engine bay identification plate, depending on market variant, and confirms the build date and chassis designation.
For engine confirmation, the TD4 badge appears on both generations but refers to different engines. On Freelander 1 vehicles produced from 2001, the TD4 is a 2.0-litre BMW M47R unit. On Freelander 2 vehicles, the TD4 is a 2.2-litre PSA DW12 unit. These engines use different parts throughout and must not be confused.
Land Rover's official VIN model year guide can help you confirm your vehicle's model year from its VIN: Land Rover VIN model year guide.
Quality TiersBudget Parts stocks three quality tiers for Freelander components, visible in the collection filter.
Genuine parts are produced by Land Rover or JLR and carry the OEM part number alongside the Land Rover branding. They are the most accurate match to the original specification. Genuine Land Rover parts are listed across both Freelander generations where available.
OEM parts are manufactured by the same original equipment suppliers that produce components for Land Rover's assembly line, but sold without Land Rover branding. These are technically equivalent to Genuine parts for most applications and are the preferred choice for workshops sourcing at trade cost.
Aftermarket parts are produced by independent manufacturers to meet or exceed OEM specification. Quality varies by manufacturer. Budget Parts selects aftermarket lines that meet the functional requirements of the original part and are appropriate for use on Freelander 1 and Freelander 2 vehicles.
For critical drivetrain, braking, and suspension components, OEM or Genuine parts are recommended. Aftermarket parts are well-suited to consumables, service items, trim components, and fasteners.
Trade BuyersThe Freelander is a common vehicle in independent workshops across the Netherlands, Belgium, and Germany. Budget Parts supplies trade buyers and garages across the EU. If you service Freelanders regularly and require volume pricing or VAT-correct invoicing for business purchases, the wholesale portal is available via the header of this site.
Technical GuidesThese articles provide deeper technical context for Freelander owners and workshop technicians. They support diagnosis and part selection and link directly to the relevant generation parts collections.
A technical reference covering driveline, transmission, body, suspension, steering, and software issues across the Freelander 2 (L359) range. Useful for identifying which components are involved before ordering replacement parts.
Freelander 2 faults and fixes guide →A maintenance-focused guide covering the most common wear items on the Freelander 1 (L314), including driveshaft assemblies, engine gaskets, and cooling components. Relevant for owners keeping older L314 vehicles in service.
Freelander 1 maintenance guide →Covers driveline fault diagnosis across multiple Land Rover models including the Freelander 2. Relevant to the VCU and IRD system on Freelander 1 vehicles and the Haldex coupling drivetrain on Freelander 2 models.
Land Rover driveshaft and driveline diagnosis →Driveshafts, propshafts, universal joints, and related driveline components for both Freelander generations.
Driveshaft and propshaft parts →Cooling system components including water pumps, thermostats, and hoses. K-series and TD4 cooling parts are common service items on the L314.
Land Rover cooling parts →Engine components for K-series, KV6, L-series, M47R, DW12, and B6324S5 power units across both Freelander generations.
Land Rover engine parts →Brake discs, pads, callipers, and hydraulic components. Use the collection filter to narrow to your Freelander generation.
Land Rover brake parts →Shock absorbers, springs, bushings, and arms. Freelander 1 and Freelander 2 use different suspension architectures, so confirm generation before ordering.
Land Rover suspension parts →Combined service kits and consumables for routine Freelander maintenance. Listed under service kits when available for your engine variant.
Land Rover service kits →No. The Freelander 1 (L314, 1997 to 2006) and Freelander 2 (L359, 2006 to 2014) use different platforms, engines, drivetrains, and electrical architectures. A Freelander 1 TD4 uses a 2.0-litre BMW M47R engine. A Freelander 2 TD4 uses a 2.2-litre PSA DW12 engine. Parts designed for one generation will not fit the other. Always confirm your generation, model year, and engine type before ordering.
The most reliable check is the production year. Freelander 1 (L314) vehicles were produced from October 1997 to 2006 and were sold in 3-door and 5-door body styles. Note that vehicles produced in late 1997 typically carry a 1998 model year designation. Freelander 2 (L359) vehicles were produced from late 2006 to October 2014 as 5-door estates only. If your vehicle was registered in late 2006 or early 2007, check the build date on the VIN plate, located on the door sill or in the engine bay. The chassis code L314 confirms a Freelander 1. The chassis code L359 confirms a Freelander 2.
Genuine parts carry Land Rover branding and are produced to OEM specification by JLR-approved suppliers. OEM parts are manufactured by the same original equipment suppliers but sold without Land Rover branding, making them a cost-effective equivalent for most applications. Aftermarket parts are produced by independent manufacturers and vary in quality. For braking, drivetrain, and suspension components, OEM or Genuine parts are recommended. For service items, consumables, and trim, quality aftermarket parts are a practical choice.
Yes. Budget Parts is based in The Hague and holds Freelander parts in EU stock. Orders are fulfilled for customers and workshops across the Netherlands, Belgium, Germany, France, and other EU member states. Fitment support and VIN-based part confirmation are available for both Freelander generations.
The Freelander 2 was discontinued in October 2014 and replaced by the Discovery Sport in 2015. The Freelander name was not used on any Land Rover vehicle after that date. A separate Freelander-branded electric vehicle is being developed under a JLR and Chery joint venture for the Chinese market, but this is an entirely different product with no parts commonality with the L314 or L359. Budget Parts supplies parts for the original Freelander 1 (L314) and Freelander 2 (L359) only.