Land Rover Freelander Parts

Vacuum Reservoir within the engine vacuum control circuit on diesel applications. The reservoir holds a reserve of vacuum that operates the turboc...

Touch-Up Paint Stick in Zambesi Silver. The stick applies a small quantity of colour-matched paint to stone chips and minor scratches, restoring t...

Touch-Up Paint Pencil in Bonatti Grey Metallic (paint code 19K512). The pencil applies a small quantity of colour-matched paint to stone chips and...

ABS G-Sensor Bracket Assembly forms part of the anti-lock braking system. The G-sensor measures longitudinal deceleration (g-force) and feeds this...

Rear Brake Shoe Set for the rear drum brake assembly. Each shoe carries a bonded friction lining and is forced outward against the inner face of t...

Handbrake Cable - left-hand cable in the parking brake system. This cable transmits the handbrake lever's travel to the rear brake actuating mecha...

Gear Lever Gaiter - flexible boot that seals around the gear shift selector rod where it passes through the floor into the transmission tunnel. Th...

Cylinder Block Plug - sealing plug fitted to the cylinder block casting. The plug closes a machined port in the block, sealing the casting so that...

Brake Pad Set - Rear provides the friction pads for the rear disc brakes. The pads sit in the rear caliper either side of the disc; when the brake...

Front Brake Calliper Bolt - a fixing within the front brake assembly. This bolt secures the front brake calliper to the hub carrier, clamping the ...

Lock Nut - self-locking threaded fastener used to secure a bolted joint against loosening under vibration. The locking feature maintains clamp loa...

Suspension Arm Bush - rubber bush for the front lower suspension arm. Pressed into the arm's mounting eye, it locates the lower arm at its chassis...

Plain Washer - M12 flat washer used in the rear suspension lower link (bottom link) assembly. Fitted on the M12 bottom-link securing bolt, where i...

Nut (M12) for the front anti-roll bar drop link, serving as the lower securing nut that retains the drop link to the suspension. The drop link con...

Bonnet Alarm Switch The bonnet position switch for the vehicle security and anti-theft system. It is mounted at the bonnet latch and detects whethe...

Pollen Filter The cabin air filter for the heating, ventilation and air conditioning (HVAC) system. It is fitted in the fresh-air intake housing, u...

Oil Pan Sealing Ring is a seal used at the oil pan (sump) of the 2.2L diesel engine, within the lubrication system. It maintains an oil-tight join...

Turbocharger Oil Feed Hose Seal in the turbocharger lubrication circuit. It seals the joint where the pressurised oil feed hose delivers engine oil...

Turbocharger Gasket for the 2.2L DW12 DOHC turbo-diesel engine. It seals the joint between the turbocharger and its mating flange, maintaining a g...

Timing Belt Idler

Washer Reservoir Cap closes the filler neck of the windscreen washer fluid reservoir. It seals the reservoir against debris ingress and fluid evap...

Clutch Retainer Tube is a retaining component in the clutch hydraulic release circuit, securing the hydraulic feed tube at the clutch slave cylinde...

Water Pump Gasket for the engine cooling circuit. The gasket seals the coolant pump against the cylinder block, sealing the coolant path between th...

Clip — a 6 mm Starlock push-on retaining washer used as a general-purpose fastener across several systems, including exhaust mounting, trim and oth...

Hose Clip for the cooling system, securing coolant and heater hose connections. This clip clamps a hose onto its pipe or stub, holding the joint t...

Freelander lampguard set 4 pcs STC7960 BFA 3001 LG321

Blanking Plug used to close off an unused port or aperture, sealing the opening against the ingress of dirt, fluid or air.

Intake Manifold Motor for the 2.5 KV6 petrol engine, mounted on the upper inlet manifold to drive the variable induction system (VIS) intake valves...

2-4 Timing Solenoid for the Jatco 5-speed automatic transmission valve body. The solenoid is mounted within the valve body and regulates the hydra...

Fastening Pin A push-fit fastener measuring 6.35 x 28.5mm, used in exterior body trim and bumper assemblies. It retains panels such as air deflect...