for Discounts / VAT
for Discounts & Correct VAT
Gearbox and transfer box parts for Land Rover and Range Rover, covering ZF automatic units, manual gearboxes, transfer cases, and the seals, bearings, and fluids that keep them running. Stocked across our Dutch warehouse network for EU dispatch, with brands including SKF, Corteco, and Timken.
Gearbox Sump Gasket for the automatic transmission oil pan. This is the gasket only - it seals the oil pan and oil screen to the gearbox case. For...
View full detailsAutomatic Transmission Sump Plug Sealing Washer in aluminium. This sealing washer fits between the sump plug and the valve block mating face, prov...
View full detailsFront Cover Gasket for the LT85 five-speed manual gearbox, G20C unit. This gasket seals the front cover to the main gearbox casing, preventing oil...
View full detailsSpring Washer - 6mm for use across gearbox, clutch and general fastening applications. A helical split spring washer for M6 fasteners, providing r...
View full detailsLayshaft for the LT76 four-speed gearbox, Suffix A only. It carries the cluster of layshaft gears below the mainshaft, driven by the constant-mesh ...
View full detailsBaulk Ring for the R380 5-speed manual gearbox synchromesh assembly. The baulk ring (also known as the synchromesh ring) is the friction cone elem...
View full detailsAutotec Reverse Light Switch for CDU51/CDU51L manual-gearbox applications. It completes the reverse lamp circuit when reverse is selected. Applica...
View full detailsDetent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...
View full detailsO-Ring - Diff Lock - LT230 provides the hydraulic seal at the differential lock mechanism and front output shaft location within the LT230 transfer...
View full detailsOil Temperature Switch - Gearbox Oil Cooler in the automatic transmission cooling circuit. This switch is mounted on the gearbox oil cooler and mo...
View full detailsAutomatic Transmission Oil Screen for the ZF 4-speed automatic transmission, fitted within the transmission oil sump. The screen filters the autom...
View full detailsTransmission Output Shaft Grease for the MT82 six-speed manual gearbox. This specialist grease is applied to the gearbox output shaft splines, whe...
View full detailsBearing transfer box OEM TIMKEN
O-Ring seals the intermediate shaft in the LT230 transfer box, sitting between the shaft mounting and the transfer casing to hold the oil seal at t...
View full detailsGearbox Gaiter Grommet seals the point where the high/low transfer lever passes through its gaiter on the LT95 four-speed gearbox. Fitted to the t...
View full detailsRetaining Plate - gearchange grommet retaining plate for the transfer box. Secures the transfer box gearchange grommet where the gear lever passes...
View full detailsGearchange Roll Pin - a tension (roll) pin used in the manual gearchange mechanism to secure the gear lever to the selector shaft. Applies to the ...
View full detailsTransmission Oil Pan and Filter for the ZF 8HP 8-speed automatic transmission (8HP45 and 8HP70, and the later 8HP51/8HP76 variants). The pan bolts...
View full detailsRelease Bearing Guide - the guide sleeve in the clutch release mechanism, mounted on the front cover of the manual gearbox. It encircles the gearb...
View full detailsMudshield
Yoke Transmission
Oil Seal Collar for the R380 manual gearbox. The collar fits over the output shaft and provides the hardened running surface against which the gea...
View full detailsLayshaft Bearing for the R380 five-speed manual gearbox. This taper roller bearing supports the layshaft (countershaft) within the gearbox casing, ...
View full detailsClevis pin
Front flange LT230
PTO Cover Gasket - LT230 seals the power take-off (PTO) aperture cover on the LT230 transfer box. It forms the joint between the PTO cover plate a...
View full detailsDistance bush mainshaft
Plate
Reverse Selector Fork for the gear selection mechanism in the Series-type manual gearbox (LT76), suffix B onwards. Mounted on the selector shaft, ...
View full detailsSynchro Hub for the 3rd/4th gear synchroniser assembly in the Series-type manual gearbox (LT76). The hub carries the synchroniser mechanism that m...
View full detailsSnap Ring
Output Shaft Bearing for the LT76 gearbox, a taper roller bearing that supports the rear output shaft. It locates the output shaft within the gear...
View full detailsMainshaft - Series 3
Oil Filter Gearbox
Layshaft Bearing for the early-type LT76 gearbox. It supports the layshaft (countershaft) within the gearbox, carrying the cluster gear that trans...
View full detailsGearbox Gasket for the LT95 four-speed gearbox, sealing the power take-off (PTO) cover joint. Fits between the PTO cover and the gearbox main casi...
View full detailsBall Steel Bearing
Thrust Washer - Mainshaft - 0.130 Inch is a gearbox internal component positioned at the 3rd gear location on the mainshaft in the Series 1, Series...
View full detailsJoint Washer for the LT76 manual gearbox. Fitted between mating faces within the gearbox to form an oil-tight joint on assembly. Supplied as a sin...
View full detailsThrust Washer - 0.128" A gearbox mainshaft thrust washer for the second-speed gear, 0.128" thick. It controls the end-float of the 2nd-speed gear ...
View full detailsGear Lever Spacer for the manual gearbox gear change assembly. It sets the position of the gear lever within the gear change housing, maintaining t...
View full detailsOil Cooler Hose for the engine oil cooling circuit on the V8 engine. Forms part of the hose assembly linking the engine oil cooler to the oil circ...
View full detailsShim
Bush
Hill Descent Control Switch - push-push switch mounted in the clutch (bell) housing, forming part of the Hill Descent Control input circuit. The s...
View full detailsGearbox and transfer box lever set, forming the visible upper section of the gear change assembly. Machined alloy levers with a silver painted fini...
View full detailsTransmission Sump and Screen for the ZF 6HP 6-speed automatic transmission. The sump bolts to the underside of the transmission case and holds the...
View full detailsPinion Shaft for the LT77 five-speed manual gearbox. This is the primary constant pinion - the input pinion of the gearbox mainshaft assembly - wh...
View full detailsCategory Overview
Every Land Rover and Range Rover uses a two-part driveline: a main gearbox that handles gear ratios and torque delivery, and a transfer box that splits drive between the front and rear axles for the brand's 4x4 traction. Both are serviceable assemblies and both are made up of parts that wear, leak, or fail individually long before the unit itself needs replacing. This collection covers the seals, bearings, synchros, gaskets, fluids, and rebuild components for the gearboxes and transfer cases fitted across the Defender, Discovery, Range Rover, Freelander, and Series ranges.
For most owners the right approach is component replacement, not unit replacement. A leaking output seal, a worn bearing, or contaminated fluid are repairable faults. Knowing which fault you have, and which part fits your specific gearbox or transfer case, is the difference between a straightforward fix and an expensive misdiagnosis.
ZF Automatic GearboxesModern Land Rover and Range Rover models run almost exclusively on ZF automatic transmissions. The ZF 6HP26 sits in the Range Rover L322, Range Rover Sport L320, and Discovery 3 and 4. The ZF 8HP series followed it across the Range Rover L405, Range Rover Sport L494, Range Rover L460, Range Rover Sport L461, and Discovery 5.
These gearboxes are precision hydraulic-mechatronic units. The valve body, torque converter, and electronic control module are the most common failure points, usually triggered by degraded fluid rather than mechanical wear. Symptoms such as delayed engagement, gear hunting, or harsh shifting on a warm gearbox typically point to valve body or fluid condition, not to a failing transmission.
For service work on these units, ZF specifies ZF Lifeguard Fluid 6 (6HP series) or ZF Lifeguard Fluid 8 (8HP series). The two fluids are not interchangeable. ZF's official position on 8HP service intervals is "fill for life", but independent transmission specialists across Europe recommend a precautionary fluid and pan-filter service at around 80,000 to 120,000 km on vehicles used for towing, urban driving, or high-mileage motorway work. For the technical detail on fluid specifications and service requirements, ZF Aftermarket publishes its own transmission oil reference guide.
Confirm the ZF gearbox code on your vehicle before ordering fluid or service kits. ZF Lifeguard Fluid 6 and Lifeguard Fluid 8 are different specifications, and using the wrong grade is the most common cause of valve body wear after a DIY service.
Manual gearboxes are less common on current production but are still the dominant powertrain across the Classic Defender, early Discovery, Freelander 1, and the Series range. The R380 was the long-running five-speed unit fitted to the Discovery 1 (post-200Tdi production), Discovery 2, and Classic Defender from the 300Tdi through to early Td5. The MT82 six-speed replaced it on the Defender 2.4 and 2.2 TDCi Puma. Earlier production used the LT77 (Discovery 1 200Tdi era) and the LT76 and LT95 on Series 2/3 vehicles.
These units fail in predictable ways. Synchroniser rings on second and third gear wear first. Input shaft and lay shaft bearings degrade with age and oil contamination. Selector linkages and detent springs cause the symptoms most often misdiagnosed as a gearbox fault. Reverse idler gear chatter is common on R380 units past 240,000 km.
For most manual-gearbox owners, parts-level repair is straightforward and rebuild kits are available for the R380, LT77, and MT82. Specific Freelander 1 parts (IB5 manual) sit under the Freelander 1 collection. Series 2/3 gearbox parts have their own fitment requirements covered under the Series 2 and 3 collection.
Transfer BoxesThe transfer box carries as much load as the gearbox and is often the part that goes ignored until it fails. The LT230 is the dominant transfer case across the Classic Defender, Discovery 1, Discovery 2, Range Rover Classic, and P38. It uses gear-drive between input and output shafts and a chain-drive system to the front output. The Discovery 3 and Discovery 4 use a chain-drive Magna Steyr unit with an electronic shift system. Modern Range Rover and Range Rover Sport models on the L405, L494, L460, and L461 platforms use a ZF-integrated transfer case as part of the transmission assembly.
Common failures are output shaft seal leaks, chain stretch on chain-drive units (Magna Steyr and modern ZF), viscous coupling failure on units fitted to early Discovery 2 and Range Rover P38, and selector motor failure on electronic-shift cases.
Transfer box fluid is not the same specification as gearbox fluid on most Land Rover and Range Rover units. The LT230 takes EP90 (or the Land Rover-specified MTF94 on later units), and the Magna Steyr unit on Discovery 3 and 4 takes a specific ATF spec. Confirm before ordering.
Most gearbox parts returns are caused by ordering errors at the buying stage rather than parts faults. The following are the most common we see across the Land Rover and Range Rover range.
For parts that overlap with the clutch system on manual gearboxes, see the Land Rover clutch parts collection. For driveline parts forward and aft of the gearbox, see the driveshaft and propshaft parts collection.
Technical GuidesIn-depth diagnostic and component guides for the gearbox-adjacent failure modes that come up most often on Land Rover and Range Rover models.
Technical breakdown of the L494's 3.0 TDV6 timing chain issues, air suspension faults, and ZF 8HP wear patterns. Covers what fails, why it fails, and which parts the workshop will need.
Range Rover Sport L494 ZF 8HP guideHow to tell drivetrain noise apart from gearbox or transfer box noise, and which parts to inspect before ordering. Covers Discovery 4, Freelander 2, and Series 3 driveline symptoms.
Land Rover driveline diagnosis guideClutch faults are routinely misdiagnosed as gearbox faults due to overlapping symptoms. This guide explains how to identify the real fault before replacing parts.
Land Rover clutch diagnosis guideThe gearbox controls gear ratios and torque delivery from the engine; the transfer box splits drive between the front and rear axles for 4x4 traction and also provides the low-range gearing on Defender and Discovery models. Both are serviceable assemblies and both fail in distinct ways. Drivetrain symptoms can come from either, which is why most Land Rover gearbox parts returns are caused by mis-diagnosis rather than mis-fit.
ZF 6HP26 transmissions (fitted to Range Rover L322, Range Rover Sport L320, Discovery 3, and Discovery 4) take ZF Lifeguard Fluid 6. ZF 8HP transmissions (fitted to Range Rover L405, L460, Range Rover Sport L494 and L461, and Discovery 5) take ZF Lifeguard Fluid 8. The two fluids are not interchangeable. Confirm the gearbox code stamped on the casing before ordering.
ZF's official position on the 8HP series is fill-for-life. In practice, independent transmission specialists across Europe recommend a precautionary fluid and pan-filter service at around 80,000 to 120,000 km, particularly on vehicles used for towing, frequent urban driving, or high-mileage motorway work. The 6HP26 typically receives a service interval at 90,000 km. Manual gearboxes (R380, MT82, LT77) take a gear oil change at approximately 60,000 km.
The LT230, fitted to the Classic Defender, Discovery 1, Discovery 2, Range Rover Classic, and Range Rover P38, fails in three main ways: output shaft seal leaks (often caused by flange wear behind the seal), input gear bearing wear, and selector linkage faults that mimic gearbox symptoms. Most LT230 issues are repairable with component-level parts rather than a full transfer case replacement.
The R380 five-speed manual was fitted to the Discovery 1 (post-200Tdi), Discovery 2, and Classic Defender from the 300Tdi era through to early Td5 production. The LT77 preceded the R380 on the Discovery 1 200Tdi. The MT82 six-speed replaced the R380 on the Defender 2.4 and 2.2 TDCi Puma. Rebuild kits and individual components for all three are stocked in this collection.
Yes. Most Land Rover transmission service jobs touch both units, particularly fluid changes, seal replacements, and bearing kits. Ordering both at the same time reduces vehicle downtime and is the most common workshop order pattern.