Land Rover Hardware & Fasteners

Flange Screw, M6 x 16mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washer...

Track spacer oil seal

Grommet

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Head Bolt Kit - a complete set of cylinder head bolts for the Rover V8 engine, securing the cylinder heads to the block and clamping the head gaske...

Aluminium Sealing Washer is a soft metal crush washer fitted under a threaded plug or fitting to form a leak-tight joint. When the bolt or plug is...

Self-Tapping Screw – No. 8 × 1/2 in is a general-purpose fastener used across body, trim and electrical fixings, such as lamp guards, wheelguards, ...

Flange Head Screw, metric M6 x 20 mm. The integral flange beneath the hex head spreads the clamping load over a wider area and helps resist looseni...

Grease Nipple is a long-thread lubrication fitting with a UNF thread form, used to deliver grease into propshaft universal joints and sliding splin...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Brake Pipe Clip (double) for ABS-equipped braking systems, used to route and secure rigid brake pipes. The double form holds two brake pipes side ...

Ball Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Flange Bolt is an M8 hexagon flange bolt with a 40 mm shank length. The integral flange beneath the head spreads clamping load over a wider bearin...

Fuel Pipe Clip securing fuel pipe within the fuel delivery system. The clip retains and locates the fuel line along its routing, holding it agains...

O-Ring sealing the front crankshaft (timing) sprocket within the timing case of the 2.5L 300TDi turbo diesel engine. It forms an oil-tight seal ar...

Cam Cover Sealing Washer Seals a camshaft cover retaining bolt on the 300 TDi 2.5L turbo diesel engine. Fitted beneath the head of the cam (rocker...

Anti-Rattle Clip secures the linkage rod within the door latch and lock mechanism. It retains the lock linkage rod at its connection point, holdin...

Tab Washer for the steering drop arm retaining nut on the Adwest steering box. Fitted beneath the drop arm nut on the steering box output shaft, t...

Castle Nut - M12 castellated nut used on the steering and suspension ball-joint fixings. Its slotted crown takes a split pin through the drilled h...

Stub Axle Bolt is a hex-head retaining screw that secures the front stub axle to the swivel pin housing. The stub axle carries the wheel hub and b...

Tab Washer locks the drop arm retaining nut on the Adwest power steering box, its tab folded against a flat on the nut to stop it working loose und...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Hub Cap closes the centre of the front hub drive flange, covering the driveshaft coupling bolts within the front axle hub assembly. This version c...

Universal Joint for the propeller shaft assembly, transmitting rotational torque between adjoining shaft sections while permitting the angular move...

A-Frame Ball Joint Fitting Kit: fitting hardware for mounting the rear A-frame fulcrum bracket and ball joint assembly.

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

The Interior Door Card Snap Sac Trim Clips are designed to securely fasten your vehicle's door card and trim pieces. Fitment: all models

Headlamp Fixing Kit for headlamps with manual beam adjustment. The kit renews the fixings and adjusters that retain the headlamp unit and set its ...

Set Screw, a hexagon-head metric fastener, M10 x 25mm. In Land Rover terminology a set screw is a bolt threaded along its full length rather than ...

Screw M6 x 20 pan-head screw. It can be used in place of LR083229 (RYG500650 / DYP500210 / EYG50080) but is not identical: this screw has no capti...

Speedo cable oil seal retainer plate

Camshaft Oil Seal seals the camshaft on the 2.5L 4-cylinder diesel engines, including the 200TDi. Fitted at the front of the engine where the cams...

Flywheel Bolt securing the flywheel to the rear flange of the crankshaft. Used on four-cylinder petrol and diesel engines, including the 200TDi an...

Turbo Oil Drain Gasket seals the turbocharger oil return on the 2.5L 300TDi. Fitted at the joint between the turbocharger oil drain (return) pipe ...

Front cover gasket 200tdi Discovery/RR

Brake Pipe Clip - Double

Core Plug for the cylinder head, sealing a core hole left in the casting during manufacture. It closes the opening left by the casting sand core a...

Plain Washer with a 6 mm (1/4") bore, a general-purpose flat washer for use with M6 fasteners. Fitted beneath a bolt head or nut to spread the cla...

Plain Washer - a flat, load-spreading washer with a 1/4 in (6 mm) bore and 5/8 in outside diameter, approximately 1/16 in thick, finished in Sherar...

Nyloc Nut with an M16 thread - a nylon-insert locking nut used on heavily loaded suspension and driveline fixings. A nylon collar set into the top...

Hex-head bolt, 3/8" UNC thread, 1-1/8" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and so...

Hex-head bolt, 5/16" UNC thread, 1" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and socke...

Engine Mounting Rubber (V8) supports the V8 petrol engine on the chassis and isolates its vibration from the bodyshell. The bonded rubber-to-metal...

Sealing Washer seals the engine oil sump drain plug, fitting between the drain plug head and the sump drain boss. When the drain plug is tightened...

Nut - an M10 self-locking hex nut used in the exhaust system to secure flanged joint and manifold connections. The self-locking feature resists lo...

Brake Pipe Clip secures and routes rigid brake pipes along the chassis within the braking system, holding them in position and guarding against cha...