Land Rover Hardware & Fasteners

Plain Washer for M10 fasteners. A flat washer fitted under a bolt head or nut to distribute the clamping load across the joint face, spread bearin...

Hex Nut, 7/16" UNF, plain steel. This full hex nut secures the door top to the door base on Series models and is used at other 7/16" UNF fixing po...

Flange Head Screw, metric M6 x 20 mm. The integral flange beneath the hex head spreads the clamping load over a wider area and helps resist looseni...

screw M5 x 12

Hex-head bolt, 5/16" UNF thread, 1" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and sockets...

Front Anti-Roll Bar Bolt secures the front anti-roll bar within the front suspension assembly. It fixes the bar to its mounting, holding it in pos...

Ball Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Drain plug LT77 R380

Flange Bolt is an M8 hexagon flange bolt with a 40 mm shank length. The integral flange beneath the head spreads clamping load over a wider bearin...

O-Ring sealing the front crankshaft (timing) sprocket within the timing case of the 2.5L 300TDi turbo diesel engine. It forms an oil-tight seal ar...

Link Clip - an anti-rattle clip for the side door latch linkage. It retains the latch operating rod within the door lock mechanism, holding the li...

Top Link Bolt - 3/4 UNF x 4 inch hexagon head bolt for securing the front top link (upper radius arm) at the fulcrum and ball joint mounting points...

Anti-Rattle Clip secures the linkage rod within the door latch and lock mechanism. It retains the lock linkage rod at its connection point, holdin...

Self-Tapping Screw – No. 8 × 1/2 in is a general-purpose fastener used across body, trim and electrical fixings, such as lamp guards, wheelguards, ...

Castle Nut - M12 castellated nut used on the steering and suspension ball-joint fixings. Its slotted crown takes a split pin through the drilled h...

Bolt - a hexagonal-head bolt with a 3/8" UNF (Unified Fine) imperial thread and a 1" length. Used as a suspension and chassis fixing at points such...

Grease Nipple is a long-thread lubrication fitting with a UNF thread form, used to deliver grease into propshaft universal joints and sliding splin...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Front Propshaft Flange Bolt Kit - the high-tensile fasteners that secure the front propshaft to its mating flanges at the transfer box and axle end...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

Hex Nut, 3/8" UNF. A general-purpose threaded fastener used at fixing points across the braking, chassis and body assemblies. The 3/8" Unified Nat...

Hex-head bolt, 1/4" UNF thread, 7/8" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socket...

Camshaft Oil Seal seals the camshaft on the 2.5L 4-cylinder diesel engines, including the 200TDi. Fitted at the front of the engine where the cams...

Washer 20mm

Flanged Bolt, M10 x 30 mm. A metric bolt with an integral flange beneath the hexagon head that spreads clamping load over a wider area and helps re...

Fuel Pipe Clip securing fuel pipe within the fuel delivery system. The clip retains and locates the fuel line along its routing, holding it agains...

Front cover gasket 200tdi Discovery/RR

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Head Bolt Kit - a complete set of cylinder head bolts for the Rover V8 engine, securing the cylinder heads to the block and clamping the head gaske...

Tab Washer for the steering drop arm retaining nut on the Adwest steering box. Fitted beneath the drop arm nut on the steering box output shaft, t...

Core Plug for the cylinder head, sealing a core hole left in the casting during manufacture. It closes the opening left by the casting sand core a...

Sealing Washer - copper sealing ring for the cooling system drain points. It seats under the radiator drain plug and the cylinder block drain tap, ...

Plain Washer with a 6 mm (1/4") bore, a general-purpose flat washer for use with M6 fasteners. Fitted beneath a bolt head or nut to spread the cla...

Plain Washer - a flat, load-spreading washer with a 1/4 in (6 mm) bore and 5/8 in outside diameter, approximately 1/16 in thick, finished in Sherar...

Nyloc Nut with an M16 thread - a nylon-insert locking nut used on heavily loaded suspension and driveline fixings. A nylon collar set into the top...

Hex-head bolt, 5/16" UNC thread, 1" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and socke...

Tab Washer locks the drop arm retaining nut on the Adwest power steering box, its tab folded against a flat on the nut to stop it working loose und...

Lokut Nut is a self-locking nut used to secure the headlamp to the body at the front wing. The self-locking design resists loosening under vibrati...

Set Screw, a hexagon-head metric fastener, M10 x 25mm. In Land Rover terminology a set screw is a bolt threaded along its full length rather than ...

Screw M6 x 20 pan-head screw. It can be used in place of LR083229 (RYG500650 / DYP500210 / EYG50080) but is not identical: this screw has no capti...

Bolt, a hexagon-head fastener with a 5/16" UNF thread, 7/8" long. This imperial fastener is of the UNF (Unified National Fine) thread series and i...

Speedo cable oil seal retainer plate

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Snap Sac Clip - a push-fit fastener that retains the interior door trim panel (door casing) to the door. The clip locates in the door frame and gr...

Thermostat Housing Gasket for the 200TDi 2.5L turbo-diesel engine, sealing the thermostat housing to the cylinder head within the engine cooling ci...