Land Rover Hardware & Fasteners

Sump Plug Washer - copper sealing washer for the sump drain plug and thermostat housing on petrol and early diesel engines. The copper washer seat...

Sump Plug Sealing Washer for the engine lubrication system. It seats between the oil drain plug and the sump pan boss, sealing the joint so the plu...

Thermostat Housing Gasket for the engine cooling system. This top gasket seals the joint between the thermostat housing and the engine, preventing...

Engine Mounting is a rubber-to-metal anti-vibration mount in the engine mounting assembly, supporting the petrol engine on the chassis frame. The ...

Exhaust Stud - Manifold to Front Pipe is a 5/16 UNF threaded stud that secures the exhaust manifold outlet flange to the front pipe in the exhaust ...

Hex Nut - 5/16" UNF is a plain hexagonal nut with a 5/16 inch UNF thread, used as a general-purpose imperial-thread fastener throughout the chassis...

Injector Sealing Washer seals the base of the fuel injector into the cylinder head on the Td5 2.5L 5-cylinder turbo diesel engine. The washer sits...

Exhaust Gasket - V8 for the exhaust downpipe assembly on V8 petrol engines. This gasket seals the flange joint at the exhaust downpipe, maintainin...

Exhaust Gasket for the front exhaust section on 2.5L TDi and V8 petrol engines. On 2.5L 200 TDi and 300 TDi 4-Cylinder engines this gasket seals t...

Hex Nut - 3/8" UNF - Full is a full-height plain hexagonal nut with a 3/8 inch UNF thread, used as a load-bearing imperial-thread fastener. It is ...

Joint Washer - front timing cover gasket for Land Rover 4-cylinder petrol and diesel engines. This gasket seals the mating face between the front ...

Carburettor Manifold Gasket for the 2.25L petrol and carburettor-equipped Defender engines. This gasket seals at the interface between the carbure...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Inlet Manifold Gasket - Diesel for the 2.25L and 2.5L 4-Cylinder diesel engine. Fitted between the inlet manifold and the cylinder head, this gask...

Axle casing oil seal

Oil seal

Exhaust Manifold Gasket for the 3.5L V8 petrol engine. This gasket seals the joint between the exhaust manifold and the cylinder head, preventing ...

Sump Drain Plug Washer - sealing washer for the engine sump drain plug on the Td5 2.5L 5-cylinder turbo diesel engine. This washer seats between t...

Thermostat Housing Gasket Seals the thermostat housing to the cylinder head within the cooling system of the 300 TDi 2.5L turbo diesel engine. It ...

Fuel Connector Block Gasket for the Td5 2.5L five-cylinder diesel engine, sealing the fuel connector block to the engine within the fuel pressure r...

Water Pump Inlet Gasket - seals the water pump inlet housing against the engine front cover within the coolant circuit. It forms the joint between...

Sealing Washer used at sealing interfaces across multiple engine assembly groups. This washer is used in rocker cover and breather assemblies, val...

Oil Filter Gasket for the engine lubrication system, sealing the oil filter bowl to the filter housing on 4-cylinder petrol and diesel engines. Th...

Inlet Manifold Gasket for the Td5 2.5L five-cylinder diesel, sealing the inlet manifold to the cylinder head. The gasket forms the air-tight joint...

Elbow Gasket seals the coolant outlet elbow, or thermostat housing, to the inlet manifold on the V8 petrol engine, forming part of the engine cooli...

Rocker cover rubber washer petrol

Water Pump Gasket Seals the coolant pump to the engine within the cooling system of the Rover V8 petrol engine. It forms a coolant-tight joint bet...

Oil drain plug TD5

Oil Cooler O-Ring for the 2.5L Td5 5-Cylinder Turbo Diesel engine. This O-ring seals the oil cooler assembly and oil filter housing to the cylinde...

Fuel Pump Gasket for the 2.0L diesel engine (Series II) and 2.25L diesel engine (Series IIA). This gasket seals between the mechanical fuel pump b...

Flanged Screw, M8 x 25 mm. A metric set screw with an integral flange beneath the hexagon head that spreads clamping load and helps resist loosenin...

Copper Sealing Washer for banjo bolt connections in the engine oil circuit. This copper washer seats against the machined face of a banjo fitting ...

Inlet Manifold Seal for the V8 petrol induction system, straight pattern. The seal closes the joint between the underside of the inlet manifold an...

Cylinder Head Dowel for the Td5 2.5L 5-cylinder turbo diesel engine. The dowel locates between the cylinder block and the cylinder head, aligning ...

Cylinder Head Bolt securing the cylinder head to the cylinder block and clamping the head gasket joint. It maintains the clamping force that seals...

Fuel Lift Pump Gasket seals the mechanical fuel lift pump to the engine on 2.5L diesel applications, including the 200TDi and 300TDi. Fitted betwe...

Engine Plug (3/8 BSF thread) for Land Rover 4-cylinder petrol and diesel engines. This threaded blanking plug is used at multiple points across th...

Water Pump Gasket - 7-Hole for the cooling system on Land Rover 4-cylinder military engines. This gasket seals the mating face between the water p...

Bottom Overhaul Gasket Set for the 3.5 V8 petrol engine. The set supplies the gaskets and seals used to reseal the lower engine once the sump is r...

Oil Seal Housing Gasket for the 300 TDi engine, sealing the rear crankshaft oil seal housing to the rear face of the cylinder block. The gasket fo...

Water Pump Gasket seals the coolant pump to the engine front cover on the V8 petrol engine. It fits at the pump mounting face, sealing the coolant...

Clutch Fork Clip secures the clutch arm rod to the release fork inside the gearbox bellhousing on LT77, LT85, and R380 5-speed manual gearboxes. T...

Oil Drain Plug threads into the drain port at the base of the engine sump, sealing the oil pan against leakage during operation. It sits within the...

Drain Plug - a tapered threaded plug used to seal and drain fluid from engine and driveline housings. It serves as a coolant drain plug in the cyl...

Manifold Stud - M8 x 36 mm - for the Td5 2.5L 5-cylinder turbo diesel engine. The stud threads into the cylinder head to locate the manifold flang...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Gearbox Mainshaft Oil Seal for the rear of the manual gearbox, sealing the mainshaft where it passes through the rear of the mainshaft-and-gears se...

Serrated Washer with a 3/8" bore, a serrated locking (shakeproof) washer. Fitted beneath a bolt head or nut, the serrated teeth bite into both the...