Land Rover Hardware & Fasteners

Bonnet Hinge Bolt Kit - a set of stainless steel fixings for mounting the bonnet hinges that allow the bonnet to pivot open. The kit secures the h...

Wiper Clip A retaining clip within the windscreen wiper assembly that secures the wiper blade to the wiper arm, holding the blade in place on the arm.

Trim Retention Clip for securing door casing and bodyside trim panels. This push-fit clip engages a panel stud on the door inner frame or body str...

Hub Bearing - the outer taper roller bearing that supports the wheel hub on the stub axle. Each wheel hub runs on a pair of opposed taper roller b...

Pop Rivet (blind rivet) for fastening panels, trim and brackets where access is only available from one side. The rivet is fitted into a drilled h...

Joint washer

Bottom Overhaul Gasket Set for the 3.5 V8 petrol engine. The set supplies the gaskets and seals used to reseal the lower engine once the sump is r...

Flanged Locking Nut, M10. General-purpose threaded fastener. The integral flange spreads the clamp load over a wider bearing area, removing the ne...

Gearbox Filter for the LT77 five-speed manual gearbox. This gauze oil strainer sits in the gearbox lubrication circuit, screening the oil drawn thr...

O-Ring - seal for the LT76 manual gearbox, seated within the transmission assembly to seal a mating joint against oil leakage. Early-type ring, fi...

Oil Seal Housing Gasket for the 300 TDi engine, sealing the rear crankshaft oil seal housing to the rear face of the cylinder block. The gasket fo...

Water Pump Gasket seals the coolant pump to the engine front cover on the V8 petrol engine. It fits at the pump mounting face, sealing the coolant...

Clutch Fork Clip secures the clutch arm rod to the release fork inside the gearbox bellhousing on LT77, LT85, and R380 5-speed manual gearboxes. T...

Bonnet Spring Retaining Clip, part of the bonnet hinge and stay assembly. Retains the bonnet (hood) tension spring against its anchor, holding the...

Oil Drain Plug threads into the drain port at the base of the engine sump, sealing the oil pan against leakage during operation. It sits within the...

Seal Retainer for the rear (3rd/5th) door aperture at the tailboard. The retainer is a profiled strip that clamps the rear door weatherseal and th...

Door Latch - Rear - Anti-Burst is the latching mechanism for the rear end door, operating within the body closure system. It mounts to the rear do...

Gear Lever Knob for the LT77 5-speed manual gearbox. Fits the main gear lever of LT77-equipped vehicles, including V8 petrol manual variants. The ...

Stainless Steel Bolt Kit for securing the front door hinges to the body on the 2-door Defender. The fasteners replace the original mild-steel fixin...

Mounting Stud is a threaded fixing used in the rear body upper fixings. It is an M8 stud, 67 mm in length, providing a fixed threaded mounting poi...

Drain Plug - a tapered threaded plug used to seal and drain fluid from engine and driveline housings. It serves as a coolant drain plug in the cyl...

Exhaust Clamp for the exhaust-to-chassis mounting. Two-bolt upper clamp plate that forms the exhaust-to-chassis mounting assembly on Series and ea...

Manifold Stud - M8 x 36 mm - for the Td5 2.5L 5-cylinder turbo diesel engine. The stud threads into the cylinder head to locate the manifold flang...

Washer Pump for the windscreen washer system, running on a 24-volt electrical supply. The pump draws fluid from the washer reservoir and delivers ...

Compression Olive for rigid fuel pipe unions. This 8 mm ferrule seats between the union nut and the fitting body, compressing onto the pipe as the ...

Radius Arm Cup Washer is the dished washer used at the front radius arm mounting, seating against the radius arm bush to spread the clamping load o...

Flange Nut, M16 for the suspension arm mountings. The integral flange spreads the clamping load over a wider bearing area and removes the need for...

Axle Oil Level Plug - a brass filler and level plug for the axle differential housing, sealed by an O-ring. It threads into the level/filler port ...

Bulkhead Vent Hinge Pin Kit in stainless steel - replaces the pivot pins on which the bulkhead (scuttle) air vent flaps hinge. The original steel ...

Transfer Box Flange Bolt - a 3/8" UNF x 1-1/4" hex-head bolt for the LT230 transfer case front output flange. It secures the drive flange to the f...

Bolt - a metric hexagon-head bolt measuring M10 x 110mm. This is a general-purpose threaded fixing used at structural and chassis mounting points,...

Gasket - LT76

Bolt securing the bulkhead to the chassis outrigger. A 1/2" UNF hex-head bolt used at the lower bulkhead mounting points, where the bulkhead fixes...

Water Pump Seal: sealing ring for the coolant pump (Land Rover description 'Seal-coolant pump'). Used in the Td5 coolant pump installation, also i...

Inlet Manifold Seal sealing the inlet manifold to the cylinder block valley on the V8 petrol engine. This formed seal closes the manifold valley j...

Swivel Shim is a 0.75 mm selective shim from the front axle swivel pin assembly. It is fitted beneath the upper swivel pin retaining plate, where s...

Water Pump Gasket Seals the coolant pump to the engine within the cooling system of the 300 TDi 2.5L diesel engine. It forms a coolant-tight joint...

O-Ring for the oil filter adaptor assembly on 4-cylinder petrol and diesel engines up to and including the 300TDi. This O-ring seals the joint bet...

Upper Spring Isolator for the coil spring suspension. This rubber seat sits at the upper end of the coil spring, between the top of the spring and ...

Chassis Harness Grommet - black rubber grommet for the chassis wiring harness, 6 x 33.5mm. Fitted where the wiring harness passes through a chassi...

Plain washer

Flange Bolt, M8 x 50 mm - a hexagon-head bolt with an integral flange beneath the head. The flange spreads the clamping load over a wider bearing ...

Brake Pad Spring Kit retains the front brake pads within the caliper, holding them against rattle and locating them on the pad retaining pins. For...

Head Gasket Set - 2.25 Petrol - Composite is a top-end (de-coke) gasket set for resealing the cylinder head assembly of the 2.25-litre petrol engin...

Exhaust Manifold Gasket Set - 2.0L & 2.6L

Gear Lever is the main gearbox selector lever. It mounts into the gearbox remote housing and is moved by the driver to engage the forward gears and...

Fuel Filler Latch Clip is a small retaining clip within the fuel filler flap assembly. It holds the spring-loaded latch in position inside the fil...

Sump Plug seals the drain aperture at the base of the engine sump, retaining the engine oil and providing the drain point for an oil change. Remov...