Land Rover Hardware & Fasteners

Flywheel Housing Stud - a mounting stud at the flywheel housing. Threaded into the housing, it provides the fixed stud onto which the mating compo...

Spring Clip - a retaining clip in the transfer gearbox selector linkage. It secures the transfer lever to its pivot, holding the gear-change lever...

Plain Washer - the upper mounting washer for the shock absorber. It seats over the top shock absorber mounting stud beneath the retaining nut, spr...

U-Bolt - a rear leaf-spring axle clamp. It passes around the axle tube and clamps the rear leaf spring to the axle seat via the lower spring plate...

Grille Screw Kit - a set of stainless steel fixing screws for mounting the front radiator grille to the body panel. The screws secure the grille a...

Grease Nipple is a long-thread lubrication fitting with a UNF thread form, used to deliver grease into propshaft universal joints and sliding splin...

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Brake Pipe Clip (double) for ABS-equipped braking systems, used to route and secure rigid brake pipes. The double form holds two brake pipes side ...

Front Bumper Securing Bolt for fastening the front bumper to the chassis crossmember. M10 thread, 120 mm long, with a black finish.

Injector Bolt secures the fuel injector clamp within the cylinder head on the 2.7 and 3.0 V6 diesel engines. The M6 x 35 mm bolt retains the clamp...

Flange Bolt is an M8 hexagon flange bolt with a 40 mm shank length. The integral flange beneath the head spreads clamping load over a wider bearin...

O-Ring sealing the front crankshaft (timing) sprocket within the timing case of the 2.5L 300TDi turbo diesel engine. It forms an oil-tight seal ar...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Front door handle LH 2A 90/110

Link Clip - an anti-rattle clip for the side door latch linkage. It retains the latch operating rod within the door lock mechanism, holding the li...

Tab Washer for the steering drop arm retaining nut on the Adwest steering box. Fitted beneath the drop arm nut on the steering box output shaft, t...

Wheel Stud for the axle hub - 16mm pull-in type. Mounts in the hub flange to carry the road wheel, which is clamped by the wheel nut running on th...

Inlet Manifold Stud with a UNF thread. Threads into the cylinder head to mount the inlet manifold, taking the manifold nut that clamps the manifol...

Joint Washer seals the gearchange/inspection cover against the transfer box casing within the transfer gearbox assembly. Fitted between the cover ...

Barrel Lock with Key A lock barrel (cylinder) supplied complete with its key, forming the keyed locking element of the door lock assembly. The bar...

Mounting Stud

Hexagon Nut with a 7/16" BSF (British Standard Fine) thread. A standard nut cut to the British Standard Fine thread form used throughout the fixin...

Lock Nut with a 5/16" BSF thread. The lock nut secures a threaded fastening against loosening under vibration, maintaining clamp load in service. ...

Exhaust Saddle Clamp for securing exhaust pipe sections to underbody mounting brackets in the exhaust system. The U-shaped saddle body seats over ...

Door Bolt Kit - a stainless steel fixing set for the four side doors (Non-Puma applications). The kit comprises M8 countersunk Allen-head bolts, J...

Castle Nut - M12 castellated nut used on the steering and suspension ball-joint fixings. Its slotted crown takes a split pin through the drilled h...

Bolt - a hexagonal-head bolt with a 3/8" UNF (Unified Fine) imperial thread and a 1" length. Used as a suspension and chassis fixing at points such...

Front Bumper Tapping Block and Bolt Set for securing the front bumper, comprising the tapping block and the associated bolt set. The tapping block...

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

The Interior Door Card Snap Sac Trim Clips are designed to securely fasten your vehicle's door card and trim pieces. Fitment: all models

Distance piece

Bumper Bolt Set in stainless steel - the fixing kit that secures the front bumper to the chassis front cross-member. This kit includes 4 x M10 x 1...

Headlamp Fixing Kit for headlamps with manual beam adjustment. The kit renews the fixings and adjusters that retain the headlamp unit and set its ...

Set Screw, a hexagon-head metric fastener, M10 x 25mm. In Land Rover terminology a set screw is a bolt threaded along its full length rather than ...

Screw M6 x 20 pan-head screw. It can be used in place of LR083229 (RYG500650 / DYP500210 / EYG50080) but is not identical: this screw has no capti...

Seal

Rear Door Hinge Pin Kit in stainless steel - a complete repair set for the rear (side-hung) door hinges, replacing corroded or worn hinge pins toge...

Heater (Glow) Plug Ballast Resistor for the diesel pre-heat circuit. Wired in series with the heater plugs, the resistor drops the battery supply t...

Double Pipe Clip for the fuel delivery system. This clip locates and retains a pair of parallel fuel pipe runs in a single fixing, holding the feed...

Turbo Oil Drain Gasket seals the turbocharger oil return on the 2.5L 300TDi. Fitted at the joint between the turbocharger oil drain (return) pipe ...

Front cover gasket 200tdi Discovery/RR

Special Fixing Washer for the hardtop side-frame mounting. Seats over the M8 side-frame mounting stud and under its securing nut, spreading the cl...

Loadspace Mat Retainer for the rear door aperture at the tailboard. The retainer is a profiled strip that clamps the rear door weatherseal and the...

Gearbox-Transfer Box Gasket for the LT76 gearbox, sealing the mating joint between the gearbox and the transfer box. The gasket maintains the oil-...

U-Bolt for the leaf spring suspension, clamping the front leaf spring to the axle. This is the short, round-top type with a 7/16" BSF thread. It p...

Core Plug for the cylinder head, sealing a core hole left in the casting during manufacture. It closes the opening left by the casting sand core a...

Exhaust Clamp Plate for the exhaust mounting assembly. Three-hole clamping plate that secures the exhaust pipe within the mounting bracket assembl...