Land Rover Hardware & Fasteners

Drain Plug for the gearbox, transfer box and axle casings. It threads into the drain point at the base of the casing to retain the oil in service, ...

Differential Pinion Bearing Spacer used in the axle differential assembly across a broad range of Land Rover models from 1965 onwards. This spacer...

Differential Washer is a plain washer used within the front and rear differential assembly. It seats beneath a threaded fastener to distribute cla...

Tank Unit Screw is the slotted cheese-head securing screw for the fuel-tank sender unit. It clamps the fuel-level sender flange down onto the top ...

Flywheel Housing Stud secures the flywheel housing to the rear of the cylinder block on the 2.0L petrol engine. The stud provides a threaded fixin...

Exhaust Manifold Stud for the 3.5L V8 petrol engine, securing the exhaust manifold to the cylinder head. The stud screws into the head and carries...

Cylinder Head Bolt clamps the cylinder head to the cylinder block on the diesel engine, compressing the head gasket to seal the combustion chambers...

Manifold Stud - a mounting stud for the manifold. Threaded into the cylinder head, it locates the manifold and clamps it to the head face via its ...

Washer used at multiple points within the manual gearbox assembly, including the main casing, extension housing, oil pump and speedometer drive hou...

Union Nut for brake and clutch hydraulic hose connections, 1/4" thread. It draws the hose union into its mating port and holds the connection tight...

Clevis Pin - pivot pin used in the mechanical brake and transmission linkages. It passes through a forked clevis and the eye of a mating rod or lev...

Bolt with a 3/8" UNF (Unified National Fine) imperial thread and a 4-1/2" shank length. A long-shank hex-head fastener for general assembly and fi...

Bolt - an imperial hexagon-head bolt with a 5/16" UNF thread and a 2-3/4" shank length. This is an engine-area fixing for early Series application...

Bolt 1/4" UNF x 2-1/2"

Drive Screw - a No. 6 x 1/2" self-tapping drive screw used across door and facia assemblies. It secures the front door glass and window regulator,...

Brake Pad Set for the front axle disc brake assembly. The pads locate within the front calipers and clamp against the vented front discs, generatin...

Clevis Pin for securing the accelerator cable at the throttle pedal end. The pin connects the inner cable to the throttle pedal arm within the mec...

Wheel Nut, Flat Type secures the road wheel to the hub studs. It has a flat, single-chamfer seating face and a 27mm hexagon.

Clip Nut spring-steel fastener that provides a captive threaded fixing point on panels and brackets. The nut clips over the edge of a panel or sli...

Timing Chain Tensioner Screw secures the timing chain tensioner within the front timing assembly of the Td5 2.5L 5-cylinder turbo diesel engine. T...

Contact Set for the Lucas 25D distributor in the ignition system of the 2.25L and 2.6L petrol engines. The contact set (breaker points) opens and ...

Inlet Manifold Seal sealing the inlet manifold to the cylinder block valley on the V8 petrol engine. This formed seal closes the manifold valley j...

ABS Modulator Switch Repair Kit serves the four-wheel anti-lock braking system, replacing the shuttle valve switch on the ABS modulator. The modul...

Headlamp Surround Retaining Screw for the front headlamp assembly. It secures the headlamp surround to the lamp housing. The screw holds the surro...

Wheel Nut for securing an alloy road wheel to the hub. It threads onto the wheel stud and clamps the wheel against the hub mounting face, providing...

Antiluce Cotter Pin for the tailgate assembly. This self-locking drop fastener secures the rear door capping fixing, retaining the tailgate hardwa...

Crankshaft Pulley Bolt for the Td5 2.5L five-cylinder turbo diesel engine, securing the crankshaft pulley and torsional vibration damper to the nos...

Screw 1/4" UNF x 1" screw used as a fixing in the upper section of the rear tailgate assembly.

Brake Caliper Seal Kit for the front hydraulic braking circuit, supplying the seals required to reseal a four-piston front brake caliper. The seal...

Plain Washer A flat washer sized for 1/4" fasteners, used as a general-purpose fixing throughout the body, chassis and mechanical assemblies. It s...

Shock Absorber Washer - Rear - a retaining washer used at the rear suspension shock absorber mounting. It seats against the lower shock absorber b...

Set Screw - a fully threaded hexagonal-head setscrew with a 3/8" UNC (Unified Coarse) imperial thread and a 7/8" length. Used as a Rover V8 engine-...

Bolt - a hexagonal-head bolt with a 5/16" UNC (Unified Coarse) imperial thread and a 3/4" length. Used as an engine-assembly fixing, including cams...

Door Hinge Nut Plate - a threaded anchor plate for the rear side door hinge. The plate sits behind the body panel at the door hinge mounting and p...

Tailgate Seal for the rear end structure. This seal fits around the tailgate aperture, sealing the joint between the tailgate and the rear body to...

Rear door sill seal RH

Rubber Seal fits along the joint between the truck cab base and the rear body, sealing where the cab meets the tub. It forms a continuous barrier ...

Cantrail Seal fits along the cantrail at the top of the rear cab, sealing the upper joint where the cab meets the roof. It runs the length of the ...

Body Side Seal is the left-hand upper rear body side seal, part of the rear body sealing assembly. It runs along the upper edge of the rear body s...

Glass seal EPDM

Bolt - 5/16" UNC x 4-3/4" is a hex bolt that secures the water pump and power steering pump on the Rover V8 engine. It has a 5/16" UNC thread and ...

double washer, restrictor

Spring Washer is an M8 double-coil spring washer used as a fastening component in body and chassis assemblies. The double-coil spring form maintai...

Driveshaft Spacer - a 15.5mm spacer used within the front and rear axle drive shaft and hub assembly. The spacer sits between the drive shaft and ...

Knuckle Joint Bolt - an M14 x 88mm hex flange bolt securing the rear knuckle to the rear cross member. The integral flange spreads clamp load acro...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Washer Dowty sealing washer for the Active Cornering Enhancement (ACE) hydraulic anti-roll system. It seals the pipe-to-actuator union, fitting at...

Blanking Plug - a threaded plug that seals an unused port or aperture in an engine casting or housing. It closes off a threaded opening not requir...