Land Rover Hardware & Fasteners

Screw 3/8" UNC x 1-1/2" used to secure the starter motor to the engine block on Rover V8 petrol engine applications. This is a 3/8 inch Unified Nat...

Bolt - 7/16" UNF x 1-1/2" imperial hex-head fastener for use in axle, suspension, and body or chassis applications requiring 7/16" UNF imperial thr...

Screw hex HD 3/8" UNC x 1-1/4"

Mainshaft Nut - castellated nut that retains the assembled components on the rear of the gearbox mainshaft. The castellations accept a split pin to...

Countersunk Screw - an M8 x 16mm countersunk screw that retains the rear brake drum to the hub. The countersunk head sits flush with the drum face...

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M5 thread with a 1...

Splash Seal

Valve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...

Valve Stem Seal fits over the valve guide at the top of the cylinder head on the 2.5L 200 TDi and 300 TDi diesel engines. It wipes and meters lubr...

Body Seal - a moulded rubber weather seal in the body & chassis assembly. It closes the gap between adjacent body panels to exclude water, dus...

Pinion Oil Seal for the rear differential, running on the drive pinion shaft. The seal sits where the pinion shaft enters the differential housing...

Gearbox Mainshaft Oil Seal, fitted where the mainshaft passes through the gearbox casing on the 5-speed manual transmission. It runs against the r...

Battery Terminal Clamp - Positive connects the positive battery lead to the positive battery post within the vehicle electrical supply circuit. It...

Battery Clamp - Negative is a single terminal clamp for the negative post of the battery. It secures the earth (negative) lead to the battery term...

Blanking Plug fills an unused switch aperture in the dashboard switch panel. Where a fascia switch position is not fitted, this plug closes off th...

Cable Tie, Panel Fixing: grey cable tie strap with a panel fixing, 4.6 x 165 mm.

Battery Clamp Bolt - fastener for the battery retention assembly. Secures the battery clamp bar across the top of the battery, holding the battery...

Exhaust Stud Nut for front exhaust system connections. This nut secures exhaust pipe sections to the manifold or downpipe studs, maintaining a gas...

Spring Washer - 6mm for use across gearbox, clutch and general fastening applications. A helical split spring washer for M6 fasteners, providing r...

Cup Washer for securing the instrument panel to the engine cowl on the Defender 90 and 110. This pressed steel cup-type washer fits beneath the in...

Sump Plug for the engine oil sump drain. Fitted to the sump drain port and removed at each oil change to drain the engine oil. The sealing washer ...

Rear Propshaft Bolt, securing the rear propshaft to the rear axle differential input flange within the rear driveline assembly. The bolt clamps th...

Propshaft Washer for the front propshaft flange connection. The washer sits at the bolted joint between the front propshaft and its mating flange,...

Propshaft Lock Washer, used within the propshaft and viscous coupling assembly. The lock washer is seated beneath the retaining fastener at the pr...

Fitment All Models From (V)6A916890

Anti-Roll Bar Fitting Kit - the rear mounting hardware used to install an uprated rear anti-roll bar in the rear suspension. The uprated bar is wi...

Turret Securing Rings - Front are reinforcement rings that fit around the front shock absorber top mount aperture in the inner wing. They distribut...

Stud

Front Wheel Hub and Bearing Assembly is the pre-assembled hub unit at the front axle, combining the wheel hub, its bearing and the ABS wheel speed ...

Rear suspension panhard rod retaining bolt used in the Radius Arms & Links assembly. This bolt secures the panhard rod to its mounting bracke...

Bolt, M10 x 30mm, used to secure the upper mounting bracket of the suspension damper. It fastens the shock absorber upper mount bracket at the fro...

Engine Plug - a threaded blanking plug used to seal machined ports and drillings in the engine, including locations in the cylinder head and the oi...

Water Pump O-Ring forms the coolant seal between the water pump and the engine front cover, within the cooling circuit. It seats in the water pump...

Rear Spring Dowel - a locating dowel that positions the rear road spring on its seat. The dowel engages a corresponding hole in the base of the sp...

Rear Shock Absorber for vehicles built with four corner air suspension, part of the rear suspension damper and air spring assembly. The air spring...

Panhard Rod Bolt for securing the panhard rod to its axle bracket or chassis mount. This is a flanged hex bolt, M16 x 75mm. The integral flange di...

Steering Column Bolt for the lower steering shaft coupling. This pinch bolt clamps the lower steering shaft to its mating joint, securing the colum...

Caged Captive Nut - an M8 nut held in a spring-steel cage that clips into a panel or bracket to provide a captive threaded fixing. It anchors the ...

Double Clip for routing and securing battery cables. This twin clip retains two leads together, holding the cabling in place along its run.

Thermostat Housing Gasket seals the joint between the thermostat housing and the engine, preventing coolant leakage at the housing mating face. Fo...

Clevis Pin for the differential lock selector linkage in the LT230 transfer gearbox. This clevis pin secures the selector lever pivot that actuate...

Gearchange Roll Pin - a tension (roll) pin used in the manual gearchange mechanism to secure the gear lever to the selector shaft. Applies to the ...

Philidas Nut is a 5/16" UNF all-metal self-locking nut. A deformed collar gives it prevailing-torque resistance to loosening under vibration, and i...

Front Radius Arm Nut - an M16 self-locking Nyloc nut used at the front radius arm mounting, part of the front suspension linkage. The radius arm l...

Fuel Tank Drain Plug - the threaded plug that seals the drain point at the base of the fuel tank. Removing it allows the tank to be drained for se...

clamp exhaust pipe RRclassic (with twin exhaust pipes)

Hose Clip is an adjustable worm-drive band clip that clamps a flexible hose onto its spigot or fitting. It tightens over the hose with a screw-dri...

Grille Retainer Nut secures the radiator grille panel to its mounting points on the front body. It threads onto the grille fixing stud to hold the...