Land Rover Hardware & Fasteners

Crankshaft Front Bolt for 2.25L Petrol, 2.5L Petrol, 2.5L Diesel NA and 2.5L Turbo Diesel engines, securing the crankshaft front pulley and timing ...

special bolt for rocker shaft 200 TDI three per engine. sold EACH! - 90/110/130 - Discovery - Range Rover Classic

Turbocharger Outlet Gasket for the 2.5L Turbo Diesel and 200TDi engines, sealing the flanged joint between the turbocharger and the exhaust elbow a...

Core Plug - Cylinder Block Expansion Port is a pressed-steel sealing plug installed in the outer face of the cylinder block to close the casting ap...

Banjo Bolt - M10 is the hollow fastener used to secure the oil feed pipe at the block-to-head junction in the lubrication circuit of the 2.25L and ...

Special Bolt for retaining the tappets in the cylinder block, part of the camshaft and tappet assembly. This is a specific-design fastener that se...

Timing Belt Tensioner Washer for 200TDi and 300TDi engines. This slotted packing washer fits to the timing belt tensioner assembly, setting the co...

Cylinder Head Gasket for the 2.5L 200/300 TDi turbo diesel engine, sealing the joint between the cylinder head and the engine block. It seals the ...

Connecting Rod Bolt for the engine bottom end, clamping the big-end bearing cap to the connecting rod around the crankshaft journal. Working as a ...

Exhaust Manifold Bolt for the Rover V8 petrol engine, threaded 3/8" UNC and 1 1/8" long. The bolt secures the exhaust manifold to the cylinder hea...

Crankshaft Pulley Bolt for Land Rover 4-cylinder engines from approximately 1989, used across the Defender, Discovery 1, and Range Rover Classic fi...

Lock Nut secures the tappet adjuster screw on the rocker shaft, holding the valve clearance once it has been set. Tightened against the rocker arm...

Crankshaft Pulley Bolt for the 2.5L 300TDi diesel engine. This bolt secures the crankshaft pulley and torsional vibration damper to the nose of the...

Throttle Potentiometer Gasket seals the throttle position sensor (throttle potentiometer) to the throttle body on the V8 EFI system. It forms the ...

Oil Filter Gasket for the four-cylinder 2.25L/2.5L petrol and 2.5L naturally aspirated diesel engines, part of the engine lubrication circuit. The...

Rocker Shaft Clamp for the cylinder head valve train on the 300TDi 2.5L turbo diesel engine. Secures the rocker shaft to the cylinder head pedesta...

Plenum Chamber Gasket for the V8 EFI petrol engine, part of the air intake and induction assembly. The gasket seals the joint at the plenum chambe...

Flywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...

Flywheel Housing Stud for the 2.5L four-cylinder diesel engine. It secures the flywheel housing to the rear face of the engine, locating the housin...

Joint Washer is a sealing washer fitted at a bolted or threaded joint on the 4-cylinder diesel engine, forming a seal between the mating faces to p...

Crankshaft Bolt is the retaining bolt that secures the pulley and damper assembly to the nose of the crankshaft on the V8 petrol engine. Threaded ...

Trim Clip is an interior trim fixing that retains the A-pillar trim panel against the body structure. Depending on application it also serves as t...

Rear Bumper Trim Retainer Clip for the Discovery 2 (L318). This plastic retainer clip secures the rear bumper finisher trim at the end-cap section...

Front Electric Window Kit converts both front door windows from manual wind-up to electric operation. The kit includes two electric window regulat...

Screw Kit - Grille & Heater Inlet is a set of stainless steel fasteners for securing the front grille and the heater inlet panel to the front b...

Tow Ball Spacer Block Kit fits between the tow ball and the tow bracket to raise the tow ball by 1.5", increasing clearance at the rear of the vehi...

Headlight Panel Screw Kit in stainless steel, for fixing the front headlight surround panels to the bodywork. The kit contains four 8 x 13 mm self...

Plastic Drive Rivet - Front Wheel Arch Liner is a push-in fastener used to secure the front wheel arch liner to the surrounding body structure. Fi...

Wheel Stud for the front and rear axle hubs on the Freelander 1. This stud is pressed into the hub flange and provides the threaded fixing point f...

Screw - Bonnet Hinge - M6 x 20 for the bonnet hinge assembly on the Defender. This M6 x 20 Torx-head screw secures the bonnet hinge. Used on vehic...

Interior Trim Fixing Clip used within body and interior trim assemblies. This clip secures trim panels, insulation sections, ducting, and fascia c...

Front Shock Absorber Bush Kit for the front suspension assembly. Bush kit for the front shock absorber mounting, providing the rubber isolation be...

Hex-Head Bolt with a 7/16" UNF (Unified National Fine) imperial thread and a 2" shank length. A fastener used in the manual steering box mounting ...

Bolt - M10 x 130mm is a hex-headed metric fastener with a 10 mm nominal thread diameter and a 130 mm shank length. It serves as a general mounting...

Bolt - Lower Steering Shaft UJ is the M8 x 35 mm clamp bolt that secures the universal joint at the lower steering shaft, within the steering colum...

Locking Nut for the steering linkage, securing the adjustable joint onto a heavy-duty drag link or steering rod. Once the joint is set to the corre...

Pop Rivet - a blind (pop) rivet for fastening panels, trim and seals where access is available from one side only. The rivet is set with a hand or ...

Special Bolt for the front suspension radius arm. This M16 bolt secures the radius arm at its mounting, locating the arm against the chassis and a...

Air Suspension Pipe Collet for the ACE (Active Cornering Enhancement) system on the Discovery 2. Push-fit retaining clip that locks the air pipe s...

Bolt is a 3/8" UNF threaded fastener used in body and chassis structural assembly, securing frame and rear-end structure components.

Anti-Roll Bar is the rear stabiliser bar within the suspension system, mounted transversely across the rear axle. Connected to the suspension thro...

Front door latch link

Clip Nut - a spring clip nut for securing heater and air ducting components. It clips over a panel edge or flange to provide a threaded seat for a...

Nut - M10 is an M10 fixing nut for general assembly and repair use across the vehicle. It threads onto an M10 stud or bolt to secure a fastened jo...

Locking Nut - a push-on locking nut for securing interior trim and ducting. It pushes onto a stud or screw thread and grips to hold the fixing cap...

seal washer for block coolant drain plug. - All 4-cylinder engines upto 1998 (except VM diesel)

Sealing Washer for the cylinder block oil jet adaptor on the 2.5L 4-cylinder diesel engine. Seals the jet adaptor against the cylinder block. Fitt...

Drop Arm Nut for the Gemmer 6-bolt steering box on the Defender 90/110 and Range Rover Classic. This hex nut secures the steering drop arm to the ...