for Discounts / VAT
for Discounts & Correct VAT
This collection covers Land Rover and Range Rover interior parts across all model families, including dashboard components, switches, trim panels, headlining, and seat hardware. Fitment varies by model, trim level, and VIN, more than for any other parts category. Selection spans OEM Genuine, Allmakes, and quality aftermarket trim and accessory parts.
Interior Trim Fixing Clip used within body and interior trim assemblies. This clip secures trim panels, insulation sections, ducting, and fascia c...
View full detailsToebox Trim Fastener - the fixing that secures the footrest and toebox trim panel in the footwell. It retains the lower trim at the A-post and toe...
View full detailsBolt - M8 x 40mm standard metric hex-head fastener for use across engine, gearbox, body, and chassis assembly applications.
Fastener - black plastic drive-type (fir tree) push-in fastener used throughout the vehicle to secure body trim panels, interior linings, underbonn...
View full detailsEarly Seat Diaphragm Door Only - Discovery 1 4
Upgrade or replace your steering wheel boss with this high-quality 36-tooth adapter, designed specifically for Land Rover Defender to 1991 90/110 v...
View full detailsGrab Handle in black, an interior assist handle that mounts to the roof trim rail. It provides occupants with a secure handhold when entering or e...
View full detailsDash Repair Kit is an interior dashboard trim kit, finished in brown, that covers the front edge of the dashboard. It addresses the peeling and cu...
View full detailsLocking Washer
Facia Assembly Fastener - a fastener for mounting the facia assembly to the dash structure. It secures the facia panel in place and is also used t...
View full detailsSill Finisher is an exterior body trim that runs along the side sill (rocker panel) beneath the doors. It covers and finishes the lower body sill ...
View full detailsElectric Seat Switch for the right-hand seat cushion adjustment, part of the powered seat control assembly. Mounted in the seat base side trim, it...
View full detailsSeat Belt Fixing Kit provides the mounting hardware used to secure a seat belt assembly to the vehicle body anchorage points. The kit supplies the...
View full detailsFlanged Clip Nut is an M6 captive nut retained in a spring-steel clip. The clip pushes onto a panel edge or into a mounting hole to hold the nut c...
View full detailsU-Type Spring Nut for the fascia (dashboard) assembly and mounting brackets. Spring-steel clip-on nut that grips a panel edge to provide a captive...
View full detailsCountersunk Screw - a machine screw with a flat, cone-shaped head that seats flush with the surface it fixes, leaving no proud edge. Metric M6 thr...
View full detailsWindow Regulator for the front door, left-hand side, manual winder type (not electric). This is the mechanism that raises and lowers the front doo...
View full detailsBrake Pedal Rubber Pad for vehicles with automatic transmission. Fitted over the brake pedal arm in the pedal box assembly, this slip-resistant ru...
View full detailsHandbrake Gaiter is the flexible boot fitted around the base of the handbrake lever where it emerges from the transmission tunnel console. It cove...
View full detailsSnap-sac trim clip - the push-in plastic fastener that secures interior trim panels to their supporting structure. The clip passes through a hole ...
View full detailsDash Repair Kit is a pre-formed interior trim cover for the dashboard top panel, finished in blue. It fits over the moulded dash top to restore th...
View full detailsSteering Wheel Boss with a 36-spline fitting. Mounts onto the splined end of the steering column and provides the bolt pattern to which the steeri...
View full detailsDoor Casing Stud - plastic push-fit stud used to secure interior trim panels to the door frame and body structure. The stud passes through the tri...
View full detailsGear Lever Gaiter, Inner. Flexible boot in the gear lever and transmission tunnel assembly. It seals the aperture where the main gearbox lever pas...
View full detailsWaterproof seat cover set for the front seats and the rear bench, finished in black. The covers are shaped to the standard seat frames and fit ove...
View full detailsWindscreen Wash/Wipe Switch - steering column stalk switch controlling the front wiper and washer circuits. The switch mounts to the column switch...
View full detailsRubber floor mat set for the passenger compartment, supplied as a complete vehicle set. The mats are shaped to the footwells and drop in over the ...
View full detailsSeat Recline Handle for the front seat backrest (squab) manual recline mechanism. This handwheel mounts on the outboard side of the seat frame and...
View full detailsWaterproof Seat Cover Set - a set of waterproof covers for the front and rear seats, finished in grey, fitted over the seats to protect the upholst...
View full detailsGrab Handle is the rear pillar (E-post) bodyside grab handle, part of the body-side trim and handle assembly. It fixes to the rear pillar to provi...
View full detailsGear Lever Gaiter Retainer - trim component within the centre console and gear lever assembly that secures the gear lever gaiter to the console. T...
View full detailsElectric Seat Switch - the left-hand seat squab control within the electrically adjustable seat circuit. This switch commands the squab (backrest)...
View full detailsMat Set Disco
Waterproof seat covers for the front seats, supplied as a pair, finished in grey. The covers are shaped to the standard seat frames and fit over t...
View full detailsRear Tread Strip protective finisher fitted to the rear end of the body, moulded in gloss black. Guards the rear sill and load-area edge against s...
View full detailsWindow Regulator - Manual - Front LH is the manually operated regulator mechanism for the front left-hand door. Driven by the window winder handle...
View full detailsLoad Space Cover Retaining Block located in the rear load area, providing the mounting point that locates and secures the load space cover. The bl...
View full detailsSeat Squab Release Button - release button for the rear seat squab (backrest) latch mechanism. Pressing the button disengages the latch so the rear...
View full detailsSunroof Crank Handle operates the manually-operated sliding sunroof. The handle engages the sunroof drive gear and provides the manual input that ...
View full detailsGlovebox Lock for the facia glovebox, the latch assembly that secures the glovebox lid closed. It mounts in the glovebox lid and engages the strik...
View full detailsLumbar Support is a pneumatic, air-adjustable lumbar support fitted within the seat back. Inflating and deflating the support varies the firmness ...
View full detailsGlovebox Lamp Assembly is the interior illumination lamp that lights the glove box compartment, forming part of the vehicle's interior lighting cir...
View full detailsDoor Trim Retainer - lower horizontal retainer for the rear end door window. This retainer secures the lower edge of the glass within the rear end...
View full detailsDash Repair Kit in grey - a set of pre-formed overlay panels that fit over the existing upper dashboard moulding. The panels cover the areas of th...
View full detailsDash Repair Kit in black - a set of pre-formed overlay panels that fit over the existing upper dashboard moulding. The panels cover the areas of t...
View full detailsCargo Liner - shaped loadspace floor liner for the Discovery 1 rear load area. The liner drops into the loadspace and covers the original floor co...
View full detailsWaterproof Seat Cover Set - a tailored cover set that fits over the front seats to protect the original upholstery from water, mud and wear. Made ...
View full detailsRubber Floor Mat Set - Rear, part of the interior floor trim. Covers the rear footwell area. The mats lay over the existing floor covering and tak...
View full detailsCategory Overview
Interior parts cover everything inside the cabin: dashboard assemblies and switches, instrument cluster components, headlining, door cards and door handles, seat trim and seat hardware, centre console parts, floor mats and load liners, sun visors, mirrors, and trim clips. The category spans every Land Rover and Range Rover model family currently supported, from Series and Classic Defender restoration parts through to current Range Rover L460 and New Defender L663 cabin components.
Coverage is broader than a single model collection because interior trim has a higher rate of shared part numbers across siblings (door cards, switches, and headlining components are often interchangeable across a generation), but trim levels, leather grades, and electronic switch packs vary by spec. Use the filter sidebar or the model-specific child collections linked below to narrow to your vehicle.
Pre-Purchase ChecklistInterior parts have the tightest fitment dependencies of any category on this site. Confirm each of the following before placing an order:
For vehicles still in mainstream production support (Discovery 5, Range Rover Sport L461, and current Defender L663), OEM Genuine remains the primary source for dashboard, switch, and electronic trim components. For classic models out of production for more than 10 years, Land Rover Classic Parts remains the official genuine source, with quality aftermarket parts (Bearmach, Britpart, Allmakes) covering the bulk of restoration interior demand.
Interior parts also sit adjacent to several other systems on the catalogue. Switch packs and instrument cluster components overlap with Land Rover electrical parts where the unit is electronic rather than purely mechanical. Door cards and headlining attachment points overlap with chassis and body parts where structural panels meet trim. Trim clips and retaining hardware overlap with hardware and fasteners when an interior repair needs replacement fixings. A single restoration job often draws from two or three of these categories together.
For model-specific interior parts, narrow to the relevant child collection: Classic Defender parts, Discovery 2 parts, Range Rover Classic parts, or Range Rover P38 parts. Each child collection filters to its model and supports a finer search across the interior catalogue.
The full Land Rover and Range Rover parts catalogue covers related cabin and trim-adjacent areas. The categories below sit next to interior parts in buyer search intent and often complete a single restoration or repair job.
External body panels, bulkhead and crossmember repair sections, structural chassis parts.
Land Rover chassis and body partsAdd-on convenience items, dog guards, roof racks, towing accessories, boot liners.
Land Rover accessoriesInterior dome lights, switch-integrated lighting, headlining-mounted fittings.
Land Rover lightingTrim clips, basic fasteners, and some switch packs interchange across siblings within a generation. Dashboards, instrument clusters, door cards, headlining, and seat hardware are model-specific and often trim-level-specific. As a general rule, anything visible inside the cabin should be confirmed by part number against the vehicle's VIN before ordering. Carryover from a sibling model is the exception, not the rule.
The VIN and the option-pack code on the build plate are the two reliable references. For vehicles built from approximately 1997 onwards, the 17-digit ISO 3779 VIN format provides model year and platform encoding. For earlier vehicles (Classic Defender Tdi-era, Discovery 1 pre-1997, Range Rover Classic), the standard digit-position rules do not fully apply and the build plate or Land Rover Heritage records are the better source.
Some platform-shared components carry over between Land Rover and Range Rover models built on the same architecture. For example, the IBF platform shared by Discovery 3 (L319) and Range Rover Sport L320 sees some common interior fittings, and the D7u platform shared by Range Rover L405, Range Rover Sport L494, and Discovery 5 L462 shares more again. Most cabin-facing trim does not interchange across model lines, however, because dashboard surfaces, switch finishes, and seat hardware are spec'd separately.
Wear and failure patterns are model-specific. Headlining sag is common on Discovery 2 and Range Rover P38 cabins as the original foam adhesive breaks down with age and heat cycling. Leather seat bolster cracking affects Range Rover Classic and early L322 driver's seats more than other panels because of the entry and exit wear pattern. Dashboard surface delamination and sticky-touch coating breakdown is a known issue on Range Rover P38 and early L322 dashboards. Switch pack failure (window switches, mirror switches, seat memory switches) is concentrated on Range Rover L322 and Discovery 3 builds where the same supplier hardware was used across the generation. When sourcing replacement parts, the wear pattern usually points to which trim level and which build-year sub-variant the vehicle started life as.
Most model generations carry at least one mid-cycle interior trim split, and several carry more than one. The Range Rover L322 (2002 to 2012) had a major refresh around 2006 that changed dashboard surfaces and switch packs. The Range Rover P38 (1994 to 2001) split its interior parts catalogue mid-production around 1999. Discovery 2 had a 2003 facelift that changed cabin trim. The current L460 Range Rover (2022 onwards) has already seen PHEV variant changes that affect rear-cabin layout. When ordering interior parts, treat the model designation as a starting point rather than a complete fitment identifier and verify the build year against the canonical parts catalogue for that generation.
Updated: May 2026