Land Rover Defender New Parts

Defender 110 Scale Model - a 1:76 scale diecast model of the Land Rover Defender 110, finished in Indus Silver. The model reproduces the Defender ...

Gasket - Oil Cooler seals the engine oil cooler to its mounting face, within the Oil Cooler and Filter assembly. It maintains the integrity of the...

Front Brake Caliper Attachment Kit - the caliper fitting hardware for the front disc brake assembly. The kit contains the brake pad clips and the ...

Brake Caliper Locating Pin Kit for the sliding brake caliper. The guide pins let the caliper float on its carrier bracket so both brake pads wear ...

Ignition Coil for the 2.0L four-cylinder petrol engine (AJ200 / AJ20P4, including PHEV). This is a coil-on-plug unit that mounts directly on the sp...

Piston Ring Set for the 5.0L V8 AJ133 petrol engine, supplied at standard bore size. The ring pack seals the combustion chamber against the cylind...

Hub Bearing

Brake Caliper Guide Pin Dust Cover for the front and rear brake calipers. The boot fits over the caliper guide pin and seals against the carrier b...

Brake Caliper Bleed Screw for the front and rear brake calipers. The bleed screw threads into the bleed port on the caliper body and is opened to ...

Camshaft Position Sensor mounted in the timing gear cover, reading the toothed target on the camshaft drive to give the engine control module a dir...

Thermostat Housing for the 5.0-litre AJ133 V8 petrol engine, part of the engine cooling circuit. The housing seats the coolant thermostat and form...

Inlet Manifold Gasket - 5.0 V8 - RH seals the inlet manifold to the cylinder head on the right-hand bank of the 5.0 litre V8 petrol (AJ133) engine,...

Inlet Valve - cylinder head inlet (induction) valve for the 5.0L V8 AJ133 supercharged petrol engine. The inlet valve admits the intake charge int...

Drive Fastener - black plastic drive-in retaining clip used to secure body mouldings, trim panels and interior finishers to their mounting panels. ...

Rear Bumper Trim - chequer-plate style protection panel for the top face of the rear bumper. Covers the exposed upper bumper surface to protect it...

Piston assembly - piston for the AJ133 5.0L supercharged V8 petrol engine, in the standard (nominal production) bore size. The piston runs in the ...

Wind Deflector Set for a four-door body, covering the front and rear door windows. The set comprises four deflectors, one for each door. Each defl...

Rear Mud Flap Pair - standard-pattern rear mudflaps in the exterior body protection assembly group. The flaps mount at the trailing edge of the re...

Front Mud Flap Pair - standard-pattern front mudflaps in the exterior body protection assembly group. The flaps mount at the trailing edge of the ...

Steering Column Repair Gaiter is a replacement gaiter for the steering column. It seals the steering column and is supplied as a repair item to re...

Piston - 0.50 mm Oversize for the 2.0-litre Ingenium (AJ200D / 204DTD) diesel engine. An engine-rebuild piston machined 0.50 mm over the standard ...

Boot Liner - a tailored load-space liner for the 110 body, shaped to fit the rear cargo area and protect the boot floor from dirt, moisture and gen...

Auxiliary Light Pod - an interior finisher panel that provides a mounting location for auxiliary switches within the cabin. Supplied with two swit...

Rear Corner Trims - chequer plate style protective trims fitted over the rear body corners to guard the panels against stone chips and abrasion. S...

Recovery Eye - a steel recovery attachment point used during vehicle recovery. It provides an eye to which a recovery strap or shackle is connected...

Crankcase Breather Cover - part of the crankcase ventilation assembly on the 3.0L Ingenium AJ20P6 six-cylinder petrol engine. The cover closes the...

Hood Latch for the bonnet closing mechanism. The latch is body-mounted and engages the bonnet striker to hold the bonnet shut, releasing when the ...

Water Pump for the 3.0L supercharged V6 and 5.0L V8 petrol (AJ133) engines. The pump circulates coolant through the engine block, cylinder heads a...

Front Suspension Arm - lower rear arm of the front suspension assembly, right-hand side. It links the lower end of the front knuckle to the subfra...

Front Suspension Arm - lower rear arm of the front suspension assembly, left-hand side. It links the lower end of the front knuckle to the subfram...

Oil Cooler, part of the engine lubrication system. It draws heat out of the engine oil to hold oil temperature within its operating range under su...

Air Suspension Levelling Valve - front valve block in the four-corner electronic air suspension circuit. It sits between the compressor and reserv...

Camshaft Sprocket is a timing-drive gear in the valve train of the 2.0L Ingenium diesel engine (AJ200D). Mounted on the end of the camshaft, it is...

Brake Actuator - electric parking brake (EPB) actuator, part of the electronic parking brake assembly. The motor-driven actuator applies and relea...

Loadspace Mat - moulded rubber mat for the loading compartment floor, part of the interior protection range. Lies over the loadspace floor coverin...

Front Axle Shaft - the front propshaft that transmits drive from the transfer case output to the front differential, feeding torque to the front ax...

Radiator is the primary heat exchanger of the Engine Cooling System, transferring heat from the engine coolant to the air drawn through the front c...

Brake Vacuum Pump, the auxiliary vacuum source for the brake servo on petrol engines. Petrol engines - particularly direct-injection and superchar...

Fuel Pump - high-pressure, engine-mounted fuel injection pump within the direct-injection fuel system on petrol engines. Driven off the engine, it...

Fan Assembly