Land Rover Defender New Parts

PCV Valve Service Kit - service parts for the positive crankcase ventilation valve, which sits in the crankcase emission control system on the cyli...

PCV Valve Service Kit

Turbocharger Coolant Hose from the engine cooling circuit, serving the turbocharger on the 3.0L AJ20P6 petrol engine. The hose carries engine cool...

Timing Chain Tensioner Arm is the pivoting guide arm in the timing drive of the 2.0L Ingenium four-cylinder petrol engine (AJ200 / AJ20P4 / AJ200P ...

O-Ring - seals a joint in the thermostat housing and EGR cooling circuit. Fitted to the 2.0L four-cylinder AJ200 diesel engine, it maintains a lea...

Brake Pad Wear Wire - front brake pad wear warning wire within the braking system. Routed to the front brake pad, the wire completes a circuit tha...

EGR Inlet Gasket for the 2.0L AJ200 Ingenium diesel Exhaust Gas Recirculation system. Seals the inlet joint of the EGR assembly to maintain a gas-...

Coolant Tube forming the primary coolant path between the cylinder block and the water outlet. This aluminium tube carries coolant from the engine...

MAP Sensor - the manifold absolute pressure sensor in the engine management system, mounted on the inlet manifold. It measures the pressure of the...

Front Crankshaft Oil Seal for the AJ200 2.0L four-cylinder petrol and diesel engine. It seals the front of the crankshaft where it passes through t...

Cylinder Head Gasket for the 2.0L Ingenium four-cylinder petrol engine (AJ200 / AJ20P4). The gasket seals the joint between the cylinder head and ...

Knock Sensor mounts on the cylinder block and detects engine knock through block vibration. It reports combustion knock to the engine management s...

Exhaust Pipe Gasket seals the front flanged joint of the exhaust system, maintaining a gas-tight connection and preventing exhaust leakage at the j...

Output Shaft Seal for the transfer box. It seals around the transfer case output shaft, retaining lubricant inside the transfer box and preventing ...

Cylinder Head Gasket for the 5.0L V8 AJ133 petrol engine. The gasket seals the joint between a cylinder head and the engine block, containing comb...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

Brake Pad Wear Wire - front brake pad wear warning wire within the braking system. Routed to the front brake pad, the wire completes a circuit tha...

Connector - Valve Block to Pipe for the air suspension system. This fitting joins the air suspension valve block to the air line, forming the seal...

O-Ring is a sealing ring used in the Exhaust Gas Recirculation (EGR) circuit of the 2.0L four-cylinder AJ200 diesel engine. It seals a joint in th...

Guide - Timing Chain

Fuel Injector Sealing Washer for the fuel injection system. Seals the fuel injector against the cylinder head, maintaining the combustion seal and...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

Cup Holder - an interior trim component fitted to the floor (centre) console. It provides a moulded holder to retain cups or containers within the...

Output Shaft Seal for the transfer box. It seals around the transfer case output shaft, retaining lubricant inside the transfer box and preventing ...

Insulator is a rubber bush fitted in the front suspension, within the front cross member and stabiliser bar assembly. It locates and cushions the ...

Exhaust Pipe Gasket seals the front flanged joint of the exhaust system, maintaining a gas-tight connection and preventing exhaust leakage at the j...

Sealing Washer is the fuel injector sealing washer for the Ingenium diesel engine (2.0L and 3.0L AJ20 / AJ21 diesel). It seats at the base of the ...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit. This seal maintains a gas-tight joint within the EGR section, sealing the connection betwe...

Front Crankshaft Oil Seal for the AJ200 2.0L four-cylinder petrol and diesel engine. It seals the front of the crankshaft where it passes through t...

Front Crankshaft Oil Seal located at the front of the cylinder block, on the crankshaft. Seals the crankshaft where it exits the front of the engi...

Insulator - Engine Support

TMAP Sensor is the combined intake air temperature and manifold absolute pressure sensor, fitted to the inlet manifold and intercooler ducting. It...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit. This seal maintains a gas-tight joint within the EGR section, sealing the connection betwe...

Exhaust Valve for the cylinder head of the 5.0L AJ133 V8 petrol engine. The valve opens to release spent combustion gases from the cylinder into t...

Exhaust Gas Pressure Sensor operates within the exhaust after-treatment system, measuring the differential pressure of exhaust gas across the diese...

Exhaust Gas Recirculation Gasket seals the joint between the EGR cooler and the EGR valve on the right-hand side, maintaining a gas-tight connectio...

Exhaust Gas Recirculation Gasket seals the exhaust gas recirculation (EGR) connection on the left-hand side, maintaining a gas-tight joint within t...

Gasket - Exhaust Manifold

Rear ABS Wheel Speed Sensor, part of the anti-lock braking and stability control system. The sensor measures the rotational speed of a rear wheel ...

Front ABS Wheel Speed Sensor, part of the anti-lock braking and stability control system. The sensor measures the rotational speed of a front whee...

Valve Spring Seat is the seat on the cylinder head that locates the base of the valve spring, providing the surface against which the spring is com...

Exhaust Clamp secures a joint between two sections of the exhaust system, clamping the adjoining pipes together to form a gas-tight connection whil...