for Discounts / VAT
for Discounts & Correct VAT
Parts for the Range Rover Evoque L538, covering all variants from 2011 to 2019 including the 5-door, 3-door, and convertible. Covers pre-facelift and post-facelift specifications. Stock is held in the Netherlands and dispatched across the EU. Use the filters to narrow by model year, category, or quality grade.
Radiator Assembly for the engine cooling system. The radiator dissipates heat from the engine coolant as it passes through the core, maintaining op...
View full detailsAir Conditioning Condenser, front-mounted, part of the refrigerant circuit. The condenser sits at the front of the vehicle ahead of the radiator, ...
View full detailsLeak Detection Pump - DMTL (Diagnostic Module Tank Leakage) unit for the fuel tank evaporative emission (EVAP) system. The module sits between the...
View full detailsShock Absorber Bracket - a mounting bracket for the rear shock absorber (damper) in the rear suspension. Locates the damper at its body mounting p...
View full detailsBrake Pad Set - front axle, part of the front disc brake assembly. The pads sit in the caliper carrier and are pressed against the brake disc by t...
View full detailsThrottle Body Assembly for the 2.0L Si4 240PS turbocharged petrol engine, mounted in the air intake tract between the intake ducting and the inlet ...
View full detailsHeater blower motor and fan assembly for the heating, ventilation and air conditioning unit. The motor drives the centrifugal fan wheel that draws...
View full detailsTiming Chain Tensioner for the 2.0L 16V TIVCT turbocharged petrol engine, operating within the timing drive assembly at the front of the engine. I...
View full detailsCrankshaft Main Bearing Set - set of main bearing shells for the crankshaft of the 204PT 2.0 litre four-cylinder engine. The main bearings carry t...
View full detailsCrankshaft Main Bearing Set - set of main bearing shells for the crankshaft of the 204PT 2.0 litre four-cylinder engine. The main bearings carry t...
View full detailsCrankshaft Main Bearing Set - set of main bearing shells for the crankshaft of the 204PT 2.0 litre four-cylinder engine. The main bearings carry t...
View full detailsEGR Cooler Repair Kit
Coolant Bypass Hose for the cooling system of the 2.2L Td4 diesel engine. Connects the water pump to the thermostat housing, carrying the bypass c...
View full detailsRear Anti-Roll Bar Link connects the rear anti-roll bar (stabiliser bar) to the suspension. The link transfers load between the anti-roll bar and ...
View full detailsStarter Motor for the 2.2L Td4 diesel engine (DW12), part of the engine starting system. It cranks the engine through a pinion that engages the ri...
View full detailsWater Outlet Connector Adaptor for the coolant circuit of the 2.0L 16V turbocharged petrol engine. It fits at the engine coolant outlet and provid...
View full detailsAdaptor
Transmission Shaft Sleeve for the AWF21 six-speed automatic transmission on all-wheel-drive applications. The sleeve houses and locates the transm...
View full detailsHaldex Service Kit for the fourth-generation Haldex coupling used in the all-wheel-drive driveline. The Haldex coupling is mounted at the front of...
View full detailsOil Pump Drive Chain for the 2.2L 16V common-rail turbo-diesel engine (DW12). It transfers drive from the crankshaft sprocket to the oil pump, mai...
View full detailsOil Pump Drive Chain for the 2.2L 16V common-rail turbo-diesel engine (DW12). It transfers drive from the crankshaft sprocket to the oil pump, mai...
View full detailsTiming Belt Tensioner
Electronic Parking Brake Actuator for the electronic parking brake (EPB) system. This motor-driven module replaces the conventional handbrake lever...
View full detailsVacuum Pump for the 2.0L 16-valve petrol (Ingenium / GTDI) engine. The pump supplies the vacuum used by the brake booster (servo) and other vacuum...
View full detailsRadiator is the engine coolant radiator for 2.2L diesel applications. It dissipates heat from the engine coolant as it flows through the core, mai...
View full detailsOil Feed Pipe for the turbocharger lubrication circuit of the 2.0L Si4 turbocharged petrol engine. It carries pressurised engine oil from the oil s...
View full detailsTyre Pressure Sensor (TPMS) for the direct tyre pressure monitoring system. Fitted at the wheel valve inside the tyre, it measures tyre pressure an...
View full detailsEngine Mounting supports the engine on the subframe and damps vibration transmitted into the body. Fitted to the 2.0L 16V TiVCT turbocharged petro...
View full detailsHeater blower motor and fan assembly for the heating, ventilation and air conditioning unit. The motor drives the centrifugal fan wheel that draws...
View full detailsVacuum Pump for the 2.0L 16-valve petrol (Ingenium / GTDI) engine. The pump supplies the vacuum used by the brake booster (servo) and other vacuum...
View full detailsWater Pump is part of the engine cooling system. It circulates coolant through the cylinder block, cylinder head and radiator to carry heat away f...
View full detailsWater Outlet Adaptor for the engine cooling circuit of the 2.0L turbocharged petrol engine (TIVCT). The adaptor forms the coolant outlet on the en...
View full detailsRocker Cover for the 2.2L DW12 diesel engine, sealing the top of the cylinder head over the camshafts and valvetrain. Also referred to as the cams...
View full detailsStarter Motor - starting motor for the 2.2L CR DI 16V turbo diesel (DW12 / TD4), part of the engine starting system. When energised by the starter...
View full detailsRocker Cover for the 2.2L DW12 diesel engine, sealing the top of the cylinder head over the camshafts and valvetrain. Also referred to as the cams...
View full detailsD3S xenon headlamp bulb, supplied with its igniter, for headlamp units originally built as bi-xenon or adaptive xenon assemblies. D3S is a mercury...
View full detailsStarter Motor for the engine starting system of the 2.0L 16-valve petrol engine (GTDI / Si4). When the key or button is turned to start, the integ...
View full detailsOil Pump Assembly for the 2.0L Si4 turbocharged petrol engine. Part of the engine lubrication system, the pump draws oil from the sump and delivers...
View full detailsBrake Disc - Front Vented - internally ventilated brake disc for the front axle, supplied as a pair. The disc mounts to the front hub and provides...
View full detailsExhaust Camshaft Sprocket for the valve timing drive on the 2.0L 16V TIVCT turbo petrol engine. Mounted on the exhaust camshaft, it is driven by t...
View full detailsOil Cooler dissipates heat from the engine oil to help maintain a stable oil operating temperature. Fitted in the lubrication circuit of the 2.0L ...
View full detailsRocker Cover for the 2.2L DW12 diesel engine, sealing the top of the cylinder head over the camshafts and valvetrain. Also referred to as the cams...
View full detailsCamshaft Sprocket A component of the timing gear that transmits drive from the timing chain to the camshaft, keeping valve operation synchronised w...
View full detailsHigh-Pressure Fuel Injection Pump for the 2.0L GTDi turbocharged petrol engine. This engine-mounted pump raises fuel to the high pressure required ...
View full detailsHigh-Pressure Fuel Injection Pump for the 2.0L GTDi turbocharged petrol engine. This engine-mounted pump raises fuel to the high pressure required ...
View full detailsExhaust Camshaft Sprocket for the valve timing drive on the 2.0L 16V TIVCT turbo petrol engine. Mounted on the exhaust camshaft, it is driven by t...
View full detailsOil Cooler dissipates heat from the engine oil to help maintain a stable oil operating temperature. Fitted in the lubrication circuit of the 2.0L ...
View full detailsIntake Camshaft Sprocket for the 2.0L 16V TIVCT turbocharged petrol engine. Driven by the timing chain, it transmits crankshaft rotation to the int...
View full detailsParts for the Range Rover Evoque L538, covering all variants from 2011 to 2019 including the 5-door, 3-door, and convertible, this collection covers pre-facelift and post-facelift specifications. If you own the 2019-onward Evoque, see the L551 parts collection.
The Range Rover Evoque L538 is the first-generation Evoque, produced at Halewood, UK from July 2011 to 2019 under chassis code L538. Model years run from 2012 to 2019. The collection covers the 5-door and 3-door SUV variants (produced through to 2018) and the convertible (produced from 2016 to 2019).
The L538 rides on the D8 platform, also known as LR-MS, a high-strength steel monocoque architecture developed by Land Rover as a heavily modified derivative of the Ford EUCD base. The D8 platform is also used on the Land Rover Discovery Sport. This architecture gives the Evoque a car-like driving character distinct from the body-on-frame and aluminium-intensive platforms used in other Range Rover generations.
Drivetrain configuration varies by variant. Four-wheel drive vehicles use a Haldex-based on-demand AWD system. Front-wheel drive was available on select diesel variants, specifically the eD4, which used a single-clutch, front-axle-only setup for improved efficiency. Confirming your drivetrain before ordering driveline, coupling, or differential components is essential. Generation-specific Haldex AWD service information is published by Haldex.
This collection does not cover the Range Rover Evoque L551 (2019 onward). If your vehicle was registered from 2019 onward, use the L551 parts collection linked in the intro above this product grid.
The L538 production run splits into two distinct specifications at the 2015 model year.
Pre-facelift vehicles (model years 2012 to 2015) used Ford-derived powerplants. Petrol variants used the 2.0L Ford EcoBoost Si4 turbo four-cylinder. Diesel variants used the 2.2L Ford Duratorq (PSA DW12) in TD4 and SD4 states of tune. The automatic gearbox on pre-facelift vehicles is the 6-speed Ford Aisin AW F-21 unit, also designated the Aisin Warner TF-81SC.
Post-facelift vehicles (model years 2016 to 2019) introduced JLR's Ingenium engine family. Both petrol and diesel variants moved to the 2.0L Ingenium turbo four-cylinder. The 9-speed ZF 9HP automatic gearbox replaced the 6-speed unit on automatic variants. The 6-speed Getrag M66EH50 manual remained available in select markets on diesel variants throughout the production run.
Engine-specific parts including oil filters, timing components, gaskets, sensors, and turbo components are not interchangeable between the Ford-derived and Ingenium specifications. Always confirm your engine code and model year before ordering.
Reference note: ZF 9HP transmission technical information is published by ZF Group.
Fitment GuidanceThe most reliable method for confirming parts fitment on an L538 is your Vehicle Identification Number (VIN). The VIN is a 17-character code stamped on the door jamb plate, on the windscreen base near the A-pillar (driver or passenger side depending on market variant), and recorded in your V5C or national registration document.
The tenth character of the VIN encodes the model year. The eighth character encodes the engine variant. If you are ordering engine-specific parts, turbo components, gearbox parts, or any item that changed at the 2015 facelift, cross-referencing your VIN with the part number is strongly recommended before purchase.
If you are unsure which specification your vehicle is, contact the Budget Parts team directly. Trade account holders can request fitment confirmation through the wholesale portal.
Catalogue ScopeThis collection includes suspension parts such as control arms, bushings, drop links, anti-roll bars, shock absorbers, and wheel bearings. Brake parts include pads, discs, calipers, brake pipes, and brake hardware. Engine parts cover oil filters, sump washers, hydraulic tappets, expansion tank caps, and ancillary components. Drivetrain parts include propshaft bolts, driveshaft components, and wheel nuts. The collection also includes electrical parts such as relays and sensors, service and maintenance items including ATF fluids and service hardware, body and chassis fixings, and workshop supplies including brake cleaner and fastener assortments.
Use the category filter above to narrow results to your area of work. The quality filter allows you to select between Genuine Land Rover, OEM, and Aftermarket grades.
Quality TiersEvery part in this collection is marked with one of three quality grades.
Genuine Land Rover parts are sourced through the official Jaguar Land Rover distribution channel. They carry the original Land Rover part number and packaging. These are the appropriate choice when OEM provenance documentation is required, such as for warranty or insurance purposes.
OEM parts are produced by the same manufacturers that supply Land Rover directly, sold outside the official JLR channel. The component is frequently identical to the Genuine part. OEM is the standard choice for independent workshops and experienced owners who want original-specification quality without the official channel markup.
Aftermarket parts are independently manufactured. Quality varies by supplier and application. Each listing specifies the grade, and the product description notes any relevant fitment or application limitations. Aftermarket is appropriate for non-critical components or where cost is the primary constraint.
TradeBudget Parts operates a wholesale portal for registered independent workshops and trade buyers across the EU. The portal provides trade pricing and account-based ordering. If you manage a workshop or operate as a parts buyer, visit the wholesale login page to access trade terms or register your account.
Generation ReferenceThe L538 is the first-generation Evoque. The second-generation Evoque, the L551, entered production in 2019 on the PTA platform with 48V mild-hybrid technology and Ingenium engines throughout. Parts are not interchangeable between generations.
For the full Range Rover model family and generation reference, see the Range Rover parts collection.
Technical GuidesThe articles below provide diagnostic and technical context relevant to Range Rover Evoque L538 owners and workshops. They support, but do not duplicate, the parts categories in this collection.
Technical guide to the L538 covering the Ford-to-Ingenium engine split, Haldex service requirements, and the suspension and platform architecture that defined the first-generation Evoque.
Range Rover Evoque L538 guide →Owner and workshop guide to the Evoque convertible covering the structural changes for the open-roof configuration, the electric roof system, AWD configuration, and common faults relevant to parts selection.
Range Rover Evoque convertible guide →The Freelander 2 shares Haldex AWD architecture and overlapping engine families with the Evoque L538. This guide covers Haldex service intervals, coupling failure patterns, and rear differential diagnosis that applies directly to L538 AWD variants.
Freelander 2 faults and Haldex service guide →The Range Rover Evoque L538 was produced from July 2011 to 2019. Model years run from 2012 to 2019. The 5-door and 3-door SUV variants were produced through to 2018. The convertible variant was introduced in 2016 and produced through to 2019. Parts availability in this collection covers the full L538 production window across all body styles.
If your vehicle was registered before 2019, it is almost certainly the L538 first generation. If registered from 2019 onward, it is the L551 second generation. The clearest confirmation is your VIN. The tenth character of your 17-character VIN encodes the model year. You can also check the driver's door jamb plate, which will show the build date and in some markets the chassis code. If you are unsure, contact Budget Parts directly before ordering.
The L538 was significantly updated at the 2015 model year. Pre-facelift vehicles use Ford-derived engines (2.0L EcoBoost petrol, 2.2L Duratorq diesel) and a 6-speed Aisin automatic gearbox. Post-facelift vehicles use JLR Ingenium engines (2.0L petrol and diesel) and a 9-speed ZF 9HP automatic. Engine-specific parts including oil filters, timing components, turbo components, and gaskets are not interchangeable between these specifications. Always confirm your model year and engine code before ordering.
Four-wheel drive variants of the L538 use an on-demand Haldex AWD system. This couples the rear axle electronically and distributes torque when front-axle slip is detected. Some diesel variants were available in front-wheel drive only, specifically the eD4, which does not use a rear differential or Haldex coupling at all. Confirming your drivetrain configuration before ordering rear axle, coupling, or propshaft components is important. If you are unsure, check your V5C or contact Budget Parts.
The L538 used two engine families across its production run. Pre-facelift vehicles (2012 to 2015 model year) used the 2.0L Ford EcoBoost Si4 turbo petrol and the 2.2L Ford Duratorq (PSA DW12) diesel in TD4 and SD4 outputs. Post-facelift vehicles (2016 to 2019 model year) used JLR's 2.0L Ingenium turbo four-cylinder in both petrol and diesel forms. Parts that are engine-specific are listed with applicable engine codes in the product descriptions.
The L538 uses the D8 platform, also known as the LR-MS. This is a high-strength steel monocoque architecture developed by Land Rover as a substantially redesigned derivative of the Ford EUCD base. The same platform underpins the Land Rover Discovery Sport. It is a different architecture to the aluminium-intensive platforms used on the Range Rover L405 and Range Rover Sport L494.
Yes. Budget Parts operates a wholesale portal for registered workshops and trade buyers across the EU. The portal provides trade pricing and account-based ordering. You can register or log in through the wholesale portal link in the site header. For volume orders or specific part enquiries, contact the Budget Parts team directly.
Updated: 13 May 2026