Range Rover L322 Parts

Brake Pad Set - Front Brakes

Rear Brake Disc - vented rotor for the rear axle, part of the rear brake disc and caliper assembly. It mounts to the rear hub and provides the fri...

Rear Brake Pad Set for the rear axle disc brakes. The friction pads are clamped by the rear brake calipers against the brake discs to generate the...

Brake Disc

Air Spring - Rear for the Electronic Air Suspension (EAS) circuit. The rear air spring mounts between the rear axle assembly and the chassis, repl...

Water Pump for the 4.4L V8 petrol engine, forming part of the coolant circulation circuit. Driven by the accessory drive belt, the pump circulates...

EGR Valve - RH

Rear Brake Disc - vented rotor for the rear axle, part of the rear brake disc and caliper assembly. It mounts to the rear hub and provides the fri...

Turbocharger Gasket

Rear Lower Suspension Arm Bush for the front pivot of the rear lower arm, within the rear knuckle and suspension arm assembly. The bush forms the ...

Lower Rear Knuckle Suspension Bush for the rear suspension. This bush fits the lower mounting of the rear knuckle (wheel carrier), forming the comp...

Brake Caliper Assembly - RH

Air Strut - LH is the left-hand front air suspension strut, a MacPherson-type unit combining a hydraulic damper and an air spring in a single corne...

Track Control Arm is the front upper control arm for the left-hand side of the independent front suspension. It locates the top of the wheel knuck...

Maintain reliable handbrake performance with this OEM handbrake shoe & lining kit, designed for Land Rover models requiring a 1-wheel applicati...

Brake Disc - Coated - vented front brake disc, part of the front disc brake assembly. The disc is mounted to the front hub and rotates with the ro...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Water Pump is the engine-driven mechanical pump that circulates coolant through the cylinder block, cylinder heads and radiator to maintain engine ...

Air Filter for the engine air intake system. The element installs in the air cleaner housing and traps airborne dust and debris from the incoming a...

Blade Assembly - Wiper

Regulator - Fuel Pressure

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

EGR Valve for the right-hand cylinder bank of the 3.6L V8 TDV8 diesel (Lion) engine, part of the exhaust gas recirculation system. The valve meter...

Mass Air Flow Sensor - air mass meter fitted in the induction tract as part of the engine management system. The sensor sits in the intake ducting...

Relay, a 70A 4-pin grey mini power relay. It provides high-current make-and-break switching for a heavy electrical load, letting a low-current con...

Lower Front Suspension Arm for the front suspension assembly. This arm connects the chassis to the lower section of the front wheel carrier, locati...

Front Brake Caliper Pin Kit covering both front calipers (left and right). The kit supplies the guide pin hardware required when servicing the fro...

Air Filter Element for the engine air intake system, seated in the air cleaner housing. It filters incoming air before it reaches the turbocharger...

Front Brake Caliper Fitting Kit - pad retaining hardware for the front brake caliper. The pins pass through the caliper body to retain the brake p...

Front Crankshaft Oil Seal for the 4.4L M62 B44 V8 petrol engine, sealing the crankshaft nose at the front of the engine. The seal is fitted into t...

Wheel Bearing for the front and rear hub assemblies. The same bearing serves all four corners. It is the sealed bearing unit clamped between the h...

Brake Hose for the front braking hydraulic circuit. This flexible hose carries pressurised brake fluid from the rigid chassis-mounted brake line to...

Radiator for the engine cooling system. Mounted at the front of the vehicle behind the grille, this radiator dissipates heat from the engine coola...

Brake Pipe - Rear is a rigid hydraulic line forming the fixed section of the rear brake circuit, carrying pressurised brake fluid from the chassis-...

Rear Knuckle Bush - Upper from the rear independent suspension knuckle assembly. The bush presses into the upper bore of the rear knuckle and form...

Glow Plug for the TDV6 2.7L and TDV8 3.6L diesel engines. Glow plugs are installed per cylinder in the cylinder head and heat the combustion chamb...

Ball Joint - Front Suspension Arm is fitted at the outer end of the upper front suspension arm, forming the pivot between the arm and the steering ...

Air Filter Element - replaceable air cleaner element for the 4.4L V8 M62 petrol engine induction system. The element is carried in the air cleaner...

Sensor - Brake Pad Wear - Front

Valve Rocker Arm for TDV6 and TDV8 diesel engines. This component operates within the cylinder head valve train, transmitting motion from the cams...

Compressor - Suspension Levelling

Brake Pad Set

Mass Air Flow Sensor - air mass meter fitted in the induction tract as part of the engine management system. The sensor sits in the intake ducting...

Coolant Expansion Tank Cap rated at 1.4 bar, fitted to the expansion (header) tank of the engine cooling system. The cap seals the expansion tank ...

Viscous Fan Coupling for the 4.4L V8 DOHC petrol engine, mounted between the front drive pulley and the engine cooling fan. The coupling drives th...

Brake Pad Set

Brake Calliper Fitting Kit for the rear brake callipers. This kit contains the slider pins and rubber dust boots for the rear brake calliper. The ...