Range Rover Parts

Gasket gearbox front cover and oil pump. LT95 4-speed gearbox - Early 110 V8, - S3 109" stage 1 V8, - 101" F.C. - Early Range Rover Classic

Flywheel Ring Gear (starter ring gear) for the diesel flywheel, part of the clutch and flywheel assembly. The toothed ring is fitted around the fl...

Differential Shim - 0.060in. Fitted during differential assembly to set bearing preload and gear alignment. Shim thickness is selected against mea...

Differential Pinion Shim - 0.052in. Fitted between the pinion head and its bearing to set pinion depth and preload during differential setup. Shim...

Differential Shim - 0.048in. Fitted during differential assembly to set bearing preload and gear alignment. Shim thickness is selected against mea...

Differential Shim, 0.040in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Differential Shim, 0.038in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Crankshaft Thrust Washer - 0.010in oversize, supplied as a pair. Fitted at the centre main bearing of the four-cylinder engine to control cranksha...

Mudguard - Power Take Off for the centre power take-off (PTO) housing. Mounted to shield the centre PTO unit from mud, water and road debris. Prot...

Gearbox Crossmember - SWB is a weld-on steel chassis crossmember that mounts beneath the gearbox and transfer box assembly, providing structural su...

Pipe Clip used to secure and route pipework such as fuel breather and roll-over anti-spill lines. The clip holds the pipe at a fixed point to prev...

Halogen Bulb - H4 100/80W (Non-CE). Dual-filament headlight bulb rated 100W high beam and 80W low beam, providing increased light output over the s...

Wheel Chock for securing a stationary vehicle. Placed against a tyre, the wedge-shaped chock prevents the vehicle from rolling when parked on an i...

Plain Washer

Bolt used in multiple assembly applications including towing equipment, engine mounting, front stabilizer bar, ACE system, and seat belt anchorage.

Locking Wheel Nut Key - Code H, the keyed adaptor that engages the splined pattern of Code H locking wheel nuts. The key is placed over the lockin...

Locking Wheel Nut Key - Code E, the keyed adaptor that engages the splined pattern of Code E locking wheel nuts. The key is placed over the lockin...

Screw is a fixing screw used to secure exterior lamp, interior lamp and trim components to the body. It retains fittings such as the high-level st...

Gearbox Extension Case Screw for the R380 5-speed manual gearbox. M5 × 30 Torx head screw used to secure the extension case on the R380 gearbox. T...

Bolt - Hexagon Head used in engine and interior fascia assembly applications. This hexagon head fastener is used in the EGR system assembly and in...

Clutch Cover Bolt secures the clutch cover (pressure plate) to the flywheel within the clutch assembly. Threaded M8 x 13mm, fitted on the 6-speed ...

Sunroof Finisher is a trim finisher for the sunroof assembly. It frames the edge of the sunroof aperture, concealing the join between the sunroof ...

Brake Light Switch

Dowel is a hollow locating dowel ring that aligns two mating housings during assembly, holding their faces in register and taking shear load off th...

Screw - No. 10 x 1 in. Secures the instrument binnacle cowl and interior air-deflector trim. Sized for self-tapping installation into moulded trim...

Differential Thrust Washer for the four-pinion differential in the Land Rover-type axle. Seats behind a differential gear to control end-float and...

Electronic Differential Lock (E-Locker) replaces the standard open differential to provide selectable, locked drive within the axle assembly. When...

The ultimate diagnostic tool for DIY use offering functionality previously only available in equipment many times more expensive. Standard diagnos...

3rd Speed Gear for the R380 five-speed manual gearbox, cut with 27 teeth. The gear sits on the mainshaft within the R380 constant-mesh gear cluste...

Synthetic Winch Rope - 10mm x 24m - 10,000 lbs for 4x4 winch recovery. This synthetic fibre winch rope is rated to 10,000 lbs (approx. 4,536 kg) b...

Vacuum Advance Unit for the ignition distributor on the 3.5L V8 petrol engine. This vacuum capsule mounts on the side of the distributor and conne...

Gear Kit - R380 - 3rd/4th Mainshaft

Portable Jump Starter and Air Compressor - a handheld 12V power pack combining a battery jump starter, power bank, tyre inflator and LED work light...

Actuator

Gearbox Bearing for the R380 5-speed manual gearbox, measuring 35 × 72 mm. Fitted within the R380 transmission assembly, this rolling-element bear...

Fitment:  Defender 110 &amp: 130 the Wolf or P38 type axle (short nose diff) 2002 on

Track Rod Clamp secures the adjustable joint of the steering track rod. Fitted around the split end of the rod, it pinches the threaded sleeve clos...

Fuel Tank Lock Ring secures the in-tank fuel pump and sender assembly to the top of the fuel tank. The ring locks down over the tank aperture, hold...

Mass Air Flow (MAF) Sensor mounted in the air intake tract, downstream of the air cleaner. It measures the mass of air drawn into the engine and s...

Air Flow Sensor for the V8 EFI petrol engine management system, mounted in the intake tract between the air filter and the throttle. Measures the ...

Filler Plug is a red anodised aluminium replacement filler plug for the radiator and thermostat housing filler points. Machined from anodised alum...

Injector O-Ring (Large) - the larger of the two sealing O-rings fitted to each fuel injector, sealing the injector into the fuel rail. Fitted to t...

Towing Bracket Slider Lock Pin is the pin that locks the vertical slider of a Dixon Bate adjustable-height towing bracket at the selected height. ...

Towing Hitch Pin is the 25mm locking pin for the Dixon Bate 3.5 tonne ball, jaw and pin hitch (DA2123 / RTC8159), retaining the coupling jaw closed...

Capture the sleek design of the Range Rover Evoque with this premium 1:76 scale diecast model in elegant Baltic Blue. This detailed replica perfect...

O-Ring for the R380 five-speed manual gearbox extension case. Seals the oil pump within the gearbox extension housing.