Range Rover Parts

Spring bonnet pull cable return

Bolt - 1/2" UNF x 6-1/4", part of the front radius arm chassis mounting. The long shank passes through the radius arm front bush and the chassis m...

Head gasket set 3.9 EFI MA on

Side Repeater Lens is the lens cover for the side repeater indicator lamp. It fits over the repeater lamp bulb to seal the unit and colour the emi...

Fuel Filler Cap that seals the fuel tank filler neck. Non-locking type with a black finish, closing the filler neck against fuel vapour loss and t...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

CuNiFer Clutch Pipe, 1/4" outer diameter, supplied for the clutch hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough t...

Stud - M10 x 25mm, a threaded fastening stud used across a range of Land Rover assemblies. The stud provides a fixed threaded mounting point, allo...

Oil Seal for the input shaft of the ZF automatic gearbox. The seal fits at the front of the gearbox, where the torque converter drives the input s...

Speedometer Drive Housing is the pinion (spindle) housing that fits to the rear flange of the LT230 transfer box. It carries the speedometer drive ...

Oil seal

Filler Plug sealing the fill and bleed point of the engine cooling system, fitted to the thermostat housing and the radiator. This plastic plug cl...

Jubilee Clip - 21-44mm is a worm-drive hose clip with a 21-44mm clamping range. The band is tightened by a captive worm screw to clamp small- to m...

Shock Absorber Bush Set - a set of four polyurethane bushes for the shock absorber mountings within the suspension damper assembly. Each bush seat...

Rubber Mounting for the body-to-chassis mounting points. The rubber is fitted under the body mounting bolt, seated between the body and the chassis...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Wheel Centre Cap in a Silver Sparkle finish with the embossed Land Rover logo, fitting the centre bore of the alloy road wheel. It conceals the hub...

Solenoid Valve Hose for the V8 EFI petrol engine, serving the plenum-mounted solenoid valve. Connects the solenoid valve into the intake plenum on...

Engine Overhaul Gasket & Seal Set for the 200TDi diesel engine, covering the bottom end of the engine. This set provides the gaskets and seals...

Hose pump to box

Track Rod End with right-hand thread, fitting at the outer end of the track rod within the steering linkage on the Defender, Discovery 1, and Range...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Exhaust Olive is a tapered sealing ring used at the exhaust system's pipe joints. It seats between two pipe sections at a compression joint, formi...

Cable Clip secures wiring harnesses, breather pipes and similar runs to the body, chassis or panel. It locates in an 8mm mounting hole and holds t...

Accelerator Cable in the throttle control linkage, connecting the accelerator pedal to the fuel injection pump. It transmits pedal movement to the...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Alternator - Lucas A127 type, 65 A output. Part of the charging system: driven by the auxiliary belt from the crankshaft pulley, it generates the c...

Water Pump for the 200TDi 2.5L turbo diesel engine, operating in the engine cooling circuit. Belt-driven from the crankshaft, the pump circulates ...

Track Rod End with a right-hand thread, forming part of the steering linkage. The track rod end is the articulating ball joint that connects the t...

Upper Link Bush for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. It seats in the upper (top) link to provide ...

Hex-head screw, 1/4" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

Drain plug

Water Pump Gasket Seals the coolant pump to the engine within the cooling system of the 300 TDi 2.5L diesel engine. It forms a coolant-tight joint...

Lower Arm Link – Rear is a rear suspension locating link connecting the rear axle to the chassis on coil-sprung suspension. It locates the axle fo...

Strap

Washer from the anti-roll bar mounting hardware. It seats beneath the fastener that secures the anti-roll bar (stabiliser bar) to its chassis mount...

Service Kit - 300TDi for Land Rover Discovery 1 and Range Rover Classic with the 300Tdi 2.5L turbodiesel engine. This kit consolidates the key ser...

Air Filter element for the air cleaner housing on the induction system. The element traps dust and airborne particles from the incoming air before...

Crankshaft Thrust Washer Pair for the 4-cylinder engine, including the 200 TDi and 300 TDi diesels. The thrust washers sit either side of the centr...

Differential Carrier Bearing is a taper roller bearing that supports the differential carrier within the axle, as part of the crownwheel and pinion...

Ignition heater plug timer glow plug relay

Brake Pipe Clip secures and routes rigid brake pipes along the chassis within the braking system, holding them in position and guarding against cha...

Brake Pipe Clip (double) used to route and secure rigid brake pipes within the braking hydraulic system. The double form retains two brake pipes s...

Exhaust Olive for the exhaust system. This tapered sealing ring fits into the slip joint between two exhaust pipe sections. As the joint clamp is ...

Lower Spring Seat locates the base of the coil spring in the suspension. It provides the lower bearing surface on which the road spring rests, pos...

Rear brake shield RH

Brake Disc Splash Shield - Front, RH, mounted behind the right-hand front brake disc. The shield sits between the stub axle / hub and the brake di...

Brake Disc - Solid - Rear is the rear brake disc, mounting to the rear hub and providing the friction surface the brake pads clamp against during b...