Range Rover Parts

Brake Pad Set for the front axle disc brake assembly, for use with solid (non-vented) front discs. The pads locate within the front calipers and cl...

Fuel Stop Solenoid for the 200 Tdi and 300 Tdi 2.5L turbo diesel engine, mounted on the fuel injection pump. Held open while energised through the...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the replaceable big-end shell bearings that fit between the connecting rods an...

Main Bearing Set for the Rover 3.5-litre V8 petrol engine. These are the replaceable shell bearings that carry the crankshaft in the cylinder block...

Radius Arm Bush - Front is the flexible mounting bush at the front radius arm-to-chassis location. The radius arm locates the front axle longitudi...

This steering drop arm transmits movement from the steering box output shaft to the steering linkage, enabling directional control at the front axl...

Wheel Spacer Set, 30 mm: silver alloy wheel spacers for a 5x165 hub, supplied as a set of four with a complete set of wheel nuts. Machined from bi...

Rear Shock Absorber provides damping control on the rear axle for suspension set up with approximately 50 mm of additional travel. Twin-tube const...

Exhaust Manifold Locking Washer that secures the exhaust manifold fixings to the cylinder head. The tab washer fits under the manifold bolt or nut...

Air Filter element for the air cleaner housing on the induction system. The element traps dust and airborne particles from the incoming air before...

Spark Plug for the petrol engine ignition system, fitted to the 2.5L four-cylinder and 3.5L/3.9L V8 petrol engines. It screws into the cylinder he...

Differential Guard for the axle differential, protecting the diff housing and cover from impact damage off-road. Clamps over the differential cent...

Front door window regulator forming part of the door glass operating assembly, responsible for controlled raising and lowering of the electric wind...

Spring Washer - M10 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to...

Plain Washer - flat washer for use in general fastening assemblies throughout the vehicle. Distributes load and protects mating surfaces under bol...

Sealing Washer seals the engine oil sump drain plug, fitting between the drain plug head and the sump drain boss. When the drain plug is tightened...

Rear suspension shock absorber designed to control vertical movement of the axle and dampen spring oscillation within the suspension system. This...

Distributor Lead for the ignition system of the 3.5L V8 petrol engine. This lead connects the distributor to the ignition amplifier module, adapti...

Repair kit for clutch master cylinder, fits to AEU1714, ANR2651.

Size/Diameter: 1/4" unf x 7/8"

Rear Brake Caliper for the left-hand side, fitted to installations using solid (non-vented) rear brake discs. The caliper carries the hydraulic pis...

Brake Caliper - Rear - RH - 7/16" UNF Mounting

Nut M16 hex nut for the front anti-roll bar assembly. Secures the front anti-roll bar (stabiliser bar) to its mounting link on the suspension.

Self-Locking Nut is an M12 x 1.25 nyloc nut used at the shock absorber mountings in the suspension. It retains the lower mounting of the front and...

Clutch Hose for the hydraulic clutch actuation system. This flexible hose provides the hydraulic connection between the rigid clutch pipework and t...

Brake Pipe Clip - a single moulded plastic clip that secures a brake pipe to the chassis within the braking hydraulic circuit. It retains the rigi...

Wheel Nut for alloy wheel fitment on Defender, Discovery 1 and Range Rover Classic. This tapered-seat wheel nut is designed for use with alloy whe...

Radius Arm Washer is a plain washer used at the radius arm mounting in the suspension. It seats under the radius arm fastener to distribute clampi...

Rear brake shield LH

Hub Outer Oil Seal for the front and rear wheel hub assemblies. Located at the outer end of the hub, it retains the wheel-bearing grease within the...

Collapsible spacer transfer box

Auxiliary Belt - ancillary drive belt for the 200 TDi engine. Runs from the crankshaft pulley to drive the engine ancillaries such as the alternat...

Heater Hose - coolant hose in the heater circuit of the V8 engine. Carries engine coolant between the engine and the heater matrix, feeding the ca...

Exhaust Downpipe is the leading section of the exhaust system, carrying gas from the turbocharger outlet rearward to the intermediate exhaust secti...

Torsional Vibration Damper mounting on the crankshaft nose of the 200Tdi 2.5L four-cylinder turbo diesel engine. Also serving as the crankshaft pu...

Oil Filler Cap closing the engine oil filler neck on the rocker cover. It seals the filler aperture to keep the lubrication system closed and prev...

Water Pump Gasket Seals the coolant pump to the engine within the cooling system of the 200 TDi 2.5L turbo diesel engine. It forms a coolant-tight...

Oil Filter Adaptor Gasket Seals the oil filter adaptor housing to the cylinder block within the lubrication circuit of the 300 TDi 2.5L diesel engi...

Cylinder Head Bolt for the 300TDi 2.5L turbo diesel engine, part of the cylinder head-to-block assembly. The bolt clamps the cylinder head onto th...

Copper Sealing Washer used to seal a threaded or banjo joint in the fuel and lubrication circuits. The soft copper deforms under tightening to con...

Carburettor Gasket - a sealing gasket for the Zenith-Stromberg 175CD carburettor as fitted to the 3.5 litre V8. It seals a joint within the carbur...

Timing Tool Kit, 12-piece, for setting the engine timing on the 2.5D, 200Tdi and 300Tdi diesel engines.

Head Bolt Set for the 300 TDi 2.5L turbo diesel engine - the bolts that clamp the cylinder head to the engine block. These are torque-to-yield (st...

Ball Joint Service Tool for the steering drop-arm ball joint. The tool presses the drop-arm ball joint (part RBG000010) into and out of the drop a...

Hexagon Bolt - an M10 x 45 mm high-tensile bolt, property class 10.9, used in the suspension top link, fulcrum and ball joint assembly. The 10.9 g...

Brake Caliper is the front left-hand hydraulic caliper in the front disc brake assembly. It houses the pistons that press the brake pads against t...

Brake Caliper is the front right-hand hydraulic caliper in the front disc brake assembly. It houses the pistons that press the brake pads against ...

Sedimentor Seal for the diesel fuel sedimentor assembly. The sedimentor separates water and sediment from the fuel ahead of the injection system. ...