Range Rover Parts

COIL IGNITION GEMS (bobineblok RR 4.6 V8) INTERMOTOR

Filler Plug in blue anodised aluminium, replacing the standard cooling system filler and blanking plug at the thermostat housing. Seals against a ...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Bolt Threaded fastener used within the exhaust system assembly.

Festoon Bulb for interior lamps. A double-ended festoon bulb that locates between the sprung contacts of the courtesy, map and interior lamp housi...

Upper Oil Cooler Pipe - feed pipe in the engine oil cooling circuit of the 4.0L V8 EFI petrol engine, carrying oil from the engine to the oil coole...

Fitment: All models (VIN) LA930456 on

Sealing Washer for the cylinder block oil jet adaptor on the 2.5L 4-cylinder diesel engine. Seals the jet adaptor against the cylinder block. Fitt...

Washer - a general-purpose fixing washer used across multiple body, brake and chassis assemblies. It spreads the clamping load of a bolt or nut ov...

Propshaft Gaiter (Sliding Joint) is the flexible rubber boot that seals the sliding splined joint of the propshaft in the drivetrain. The sliding ...

Spring Washer for use across a wide range of fixings and assembly applications on Land Rover vehicles. This split-ring spring washer is placed ben...

Screw hex HD 3/8" UNC x 1-1/4"

Heater Motor Adaptor Lead for the heater blower motor and fan assembly. This wiring adaptor bridges the blower motor to the vehicle's existing heat...

Camshaft O-Ring for the 2.5L four-cylinder diesel engines, including the naturally aspirated diesel, turbo diesel and 200TDi. This O-ring forms th...

Silicone Turbo & Intercooler Hose Kit - a three-piece set of silicone charge-air hoses for the 300Tdi turbo and intercooler circuit, replacing ...

Locking Washer for the swivel pin housing on the front axle. The washer sits under the swivel pin retaining bolts, and its tab is bent up against t...

Mainshaft Bearing supports the mainshaft within the LT230 transfer box, carrying the shaft's rotational loads and keeping it running true as drive ...

Rear Side Door Channel is a glass run channel mounted within the rear side door, fitted to the right-hand (RH) side. The channel locates and guide...

Fuel Temperature Sensor for the EFI V8 petrol engine, part of the electronic fuel injection management system. The sensor measures the temperature...

Reverse switch R380 Frl.1 manual

Shock Absorber Bush Set for the shock absorber mountings. This set provides the bushes that locate each shock absorber at its mounting eyes, insul...

P-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...

Sedimentor O-Ring for the diesel fuel filter assembly. This rubber sealing ring seals the sedimentor bowl against the filter head, preventing fuel...

Clip - a retaining clip used to secure finisher mouldings and column shroud panels to their supporting structure. It locates and holds the mouldin...

Power Steering Pump - the engine-driven pump at the heart of the power steering hydraulic circuit. Belt-driven from the engine, it draws fluid fro...

Idler Pulley for the air conditioning auxiliary belt drive on 300TDi engines. This pulley operates within the A/C belt drive circuit, maintaining ...

Idler Pulley for the air conditioning auxiliary belt drive on 300TDi engines. Positioned within the A/C belt routing circuit, this pulley guides t...

Temperature Transmitter is the coolant temperature sender within the engine cooling and instrument gauge circuit, for V8 petrol applications and ca...

Cap Reservoir Br.m.cylinder

Distributor Vacuum Advance Unit for the 2-pin electronic distributor on the 3.5L V8 petrol engine. The vacuum unit mounts on the side of the distr...

Power Steering Pipe O-Ring - a seal in the power steering hydraulic circuit. It fits at the union between a power steering pipe and its mating conn...

Kit - Timing Belt - 200TDi

Brake Master Cylinder for the brake hydraulic circuit, converting brake-pedal force into hydraulic pressure supplied to the front and rear brake li...

Intercooler Hose for the 200TDi 2.5L turbocharged diesel engine intercooler circuit on the Discovery 1 and Range Rover Classic. This hose forms pa...

Steering Box is the steering gear at the heart of the power-assisted steering circuit. It converts steering-wheel rotation into lateral movement o...

Fuse rated at 7.5A for the vehicle electrical system. Fitted in the fusebox to protect a circuit rated at 7.5 amps, the fuse breaks the connection...

O-Ring is a sealing ring used within the ZF 4-speed automatic gearbox and the LT230 transfer box. This O-ring seals fluid passages or housing inte...

Front Cover Gasket sealing the timing cover to the front face of the cylinder block on the 300TDi 2.5L turbo diesel engine. It forms the oil-tight...

Clutch Push Rod (9.2 cm) for the clutch release hydraulic circuit, working between the clutch slave cylinder and the release lever. The rod transm...

Countersunk Screw for the Transmission Brake Assembly. The countersunk head sits flush within the mating surface, maintaining correct alignment and...

Trip Indicator Slip Ring located in the steering wheel and column assembly. The slip ring maintains a continuous electrical connection between the...

Flywheel Housing Stud for the 2.5L four-cylinder diesel engine. It secures the flywheel housing to the rear face of the engine, locating the housin...

Core Plug - Cylinder Block Expansion Port is a pressed-steel sealing plug installed in the outer face of the cylinder block to close the casting ap...

CV Joint Spacer for the front axle drive shaft. Fits on the front halfshaft to correctly space the constant-velocity (CV) joint, setting its seati...

O-Ring - Diff Lock - LT230 provides the hydraulic seal at the differential lock mechanism and front output shaft location within the LT230 transfer...

Circlip - Output Shaft Flange used within the transfer box output flange assembly to retain the output shaft bearing and associated components in p...

Sac Snap Clip

Timing Belt Tensioner Washer for 200TDi and 300TDi engines. This slotted packing washer fits to the timing belt tensioner assembly, setting the co...