Range Rover Parts

Drain Plug - Coolant - Cylinder Block is the threaded plug that seals the coolant drain port in the cylinder block, providing a controlled drain po...

Crankshaft Bolt is the retaining bolt that secures the pulley and damper assembly to the nose of the crankshaft on the V8 petrol engine. Threaded ...

Relay operates within the anti-theft alarm and central locking circuit. This relay switches power to the alarm and remote central locking system, ...

seal washer for block coolant drain plug. - All 4-cylinder engines upto 1998 (except VM diesel)

Cable Tie for securing wiring looms and cables in Land Rover applications.

Trunnion

Spire Nut, a J-type sheet-metal spring nut (also known as a speed nut) used to secure trim, panels and fittings. The nut clips over a panel edge o...

Banjo Bolt secures the breather pipe to an axle, gearbox or transfer case housing. The bolt is drilled through its shank and head so that, clamped...

M6 Stud for the gearbox main casing. This threaded stud secures the speedometer drive housing to the transmission main casing, providing the fixin...

Blanking Plug - a push-fit plug used to close an unused aperture in a body panel, door or interior trim component. It seals the opening against wa...

Grommet - rubber sealing grommet, 3/4 inch overall diameter with 1/8 inch centre hole. Used to seal and protect wiring cables where they pass thro...

Layshaft Bearing for the LT77 and R380 5-speed manual gearbox fitted to the Defender, Discovery 1, Discovery 2, and Range Rover P38. The layshaft ...

Shock Absorber Bush Kit for the mounting points of Terrafirma TS-series shock absorbers. The kit provides the hardware required to replace worn bu...

Steering Damper - 4-Stage Adjustable for Land Rover Defender 90, 110, and 130. This hydraulic steering damper mounts between the axle and chassis ...

Turret Securing Rings - Front are reinforcement rings that fit around the front shock absorber top mount aperture in the inner wing. They distribut...

Shock Absorber for the rear suspension, controlling axle movement and damping spring oscillation between the axle and the chassis mounting points. ...

Front Shock Absorber provides damping control on the front axle for suspension raised by approximately 50 mm. Twin-tube big-bore construction with...

Clutch Damper for 200TDi and 300TDi diesel engines. This in-line hydraulic damper fits within the clutch hydraulic hose run between the master cyl...

Injector Pipe - No.4 is a rigid high-pressure fuel line in the injection circuit of the 2.5L 300 TDi turbo diesel engine. It carries metered fuel ...

Decoke Gasket Set for the 3.5L V8 petrol engine with fuel injection (EFI). The set supplies the gaskets and seals needed when the cylinder heads a...

Servo unit RRcl D1

Brake Caliper Piston Kit - replacement pistons for the rear brake caliper. The pistons run in the caliper bores and, under hydraulic pressure, pre...

Countersunk Screw - M6 x 12mm is a metric fastener used across multiple assemblies on Land Rover vehicles, including brake disc and drum retention ...

Fitment: All non ABS models (VIN) JA032851 on to (axle) 38L03120B. 39L05552B. 42L00521B. 43L18579B All Models From (A)57L00001B To (A)57L05188B0

Alternator of the Lucas A133 type, rated at 85A, for V8 EFI petrol engines. Driven by the auxiliary belt from the crankshaft as part of the engine...

Fuse rated at 15A for the vehicle electrical system. Fitted in the fusebox to protect a circuit rated at 15 amps, the fuse breaks the connection w...

Power steering seal kit

Power Steering Hose - Box to Reservoir is a hydraulic hose in the power steering return circuit. This hose carries hydraulic fluid from the steeri...

Drop Arm - LHD - D1/RRC

Bottom Radiator Hose - the lower coolant hose in the engine cooling circuit, connecting the radiator outlet to the water pump inlet. It returns co...

Radius Arm Bush - Front - mounts the front radius arm at its axle end within the front suspension. The radius arm locates the front axle longitudi...

Handbrake Cable transmits lever movement to the transmission handbrake, the drum brake mounted on the transfer box rear output. The outer sheath i...

Radius Arm Bush Set - Polyurethane fits at the axle end of the front radius arms, within the front suspension radius arm and axle location assembly...

Upper Link Bush Set - Polyurethane for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. Supplied as a set of two ...

Fuel Sedimentor is a water and sediment trap in the diesel fuel supply line, installed upstream of the fuel filter and injection pump. Fuel passes...

Axle Breather Pipe Clip from the axle breather system, retaining the breather hose along its run from the axle case up to its higher mounting point...

Front Coil Spring is a front road suspension coil spring for V8 petrol, left-hand-drive applications. It supports the front of the vehicle and set...

Heater Hose for the 200TDi engine cooling and heating circuit. This hose routes coolant from the engine cooling system to the cabin heater matrix,...

Heater Inlet Hose is a moulded coolant hose in the cabin heater circuit of the 200TDi 2.5L turbo diesel engine. It carries hot coolant from the en...

Exterior Door Handle Seal for the door locks and handles assembly. The seal sits between the outer door handle and the door skin, closing the gap ...

Bonnet Striker is part of the bonnet latch mechanism — the striker that the bonnet catch engages to hold the bonnet closed. When the bonnet is shu...

Window Regulator operates the manual front door glass on the right-hand side, forming part of the door window lift assembly. Mounted inside the do...

Oil Sump Drain Plug, bolt and washer assembly, for the Rover V8 EFI engine. The drain plug seals the oil sump drain aperture at the base of the en...

Brake Disc - a vented front brake disc for the front axle braking system. The disc rotates with the front wheel hub and is clamped by the caliper ...

Release Bearing Guide - the guide sleeve in the clutch release mechanism, mounted on the front cover of the manual gearbox. It encircles the gearb...

DIFFERENTIAL - ASSEMBLY - FRONT AXLE - 24 SPLINE - 4 BOLT FLANGE - D2

Mudshield

Yoke Transmission