Range Rover Parts

Gear Lever Spring for the manual gearbox gear change mechanism, providing the 5th gear selector bias. It works within the gear lever remote housing...

Gear Lever Spring for the manual gearbox gear change mechanism, providing the 1st/2nd selector bias. It works within the gear lever remote housing,...

Joint Washer - LT77 Front Cover seals the mating face between the front cover and the main casing of the LT77 5-speed manual gearbox. The washer p...

Upper Front Swivel Pin for the front axle swivel housing assembly. The upper swivel pin bolts to the top of the swivel housing and forms the upper...

Clutch Driven Plate for the V8 clutch assembly. It is carried on the gearbox input shaft between the flywheel and the clutch cover (pressure plate)...

Clevis pin

Taper Roller Bearing for the front output shaft of the LT230 transfer box. Installed within the LT230 transfer case differential lock and output s...

Outer Shim - 1.65mm - Front Halfshaft / CV Joint This 1.65mm shim is used to set the end-float of the front halfshaft within the CV joint assembly...

Outer Shim - 1.35mm - Front Halfshaft / CV Joint This 1.35mm shim is used to set the end-float of the front halfshaft within the CV joint assembly...

Half Shaft Shim is a 1.05mm selective shim used in the front axle drive shaft and hub assembly. It sets the endfloat of the front half shaft drive...

PTO Cover Gasket - LT230 seals the power take-off (PTO) aperture cover on the LT230 transfer box. It forms the joint between the PTO cover plate a...

Valve Stem Seal fits over the valve guide at the top of the cylinder head on the 2.5L 200 TDi and 300 TDi diesel engines. It wipes and meters lubr...

special bolt for rocker shaft 200 TDI three per engine. sold EACH! - 90/110/130 - Discovery - Range Rover Classic

Camshaft for the five-bearing four-cylinder engine, running in the cylinder block as the core of the overhead-valve valvetrain. Driven from the cr...

Special Bolt for retaining the tappets in the cylinder block, part of the camshaft and tappet assembly. This is a specific-design fastener that se...

Engine Cooling Fan - 11-blade, 17-inch diameter mechanical fan for the engine cooling system. Driven from the front of the engine via a viscous co...

Intercooler Hose for the 200 TDi turbocharged induction system. Part of the charge-air ducting that links the intercooler into the boost circuit, ...

Cylinder Head Gasket for the 2.5L 200/300 TDi turbo diesel engine, sealing the joint between the cylinder head and the engine block. It seals the ...

Camshaft for the 3.9L V8 EFI petrol engine. Mounted within the cylinder block of this overhead-valve, cam-in-block engine, the camshaft is driven ...

Drive Belt is the serpentine (poly-vee) accessory belt for the 4.0L V8 EFI petrol engine fitted with air conditioning. Driven from the crankshaft ...

Crankshaft Pulley Bolt for the 2.5L 300TDi diesel engine. This bolt secures the crankshaft pulley and torsional vibration damper to the nose of the...

Boost Pipe Assembly for the 2.5L 300 TDi turbo diesel, part of the turbocharger boost control circuit. It connects the inlet manifold to the injec...

Rocker Shaft Clamp for the cylinder head valve train on the 300TDi 2.5L turbo diesel engine. Secures the rocker shaft to the cylinder head pedesta...

Intercooler Hose for the 2.5L 300TDi 4-cylinder turbo diesel engine on EGR-equipped variants. This rubber hose connects the intercooler to the int...

Thermostat Housing for the 2.5L 300TDi 4-cylinder turbo diesel engine. This housing secures the engine thermostat within the cooling circuit and f...

O-Ring - Oil Pick-Up Pipe for the 2.5L 300TDi 4-cylinder turbo diesel engine. This O-ring seals the oil pick-up pipe connection at the oil pump or...

Inlet Valve Rocker Arm - a valvetrain component in the rocker shaft assembly of the 2.5L 300 TDi turbo-diesel engine. Mounted on the rocker shaft,...

Exhaust Valve Rocker Arm - a valvetrain component in the rocker shaft assembly of the 2.5L 300 TDi turbo-diesel engine. Mounted on the rocker shaf...

Plenum Chamber Gasket for the V8 EFI petrol engine, part of the air intake and induction assembly. The gasket seals the joint at the plenum chambe...

Flywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...

Oil Separator Drain Hose for the crankcase ventilation system on the 2.5L naturally aspirated diesel and 200TDi turbo diesel engines. It drains th...

Pulley

Joint Washer is a sealing washer fitted at a bolted or threaded joint on the 4-cylinder diesel engine, forming a seal between the mating faces to p...

Spring Retaining Plate for the front coil spring suspension. The plate seats the upper end of the front coil spring against the chassis spring seat...

Heater Bypass Coolant Valve for V8 petrol applications. This vacuum-operated valve is installed in the HVAC coolant circuit and controls the flow ...

Receiver Dryer for the air conditioning system, compatible with R134a refrigerant. Installed on the high-pressure side of the A/C circuit, between...

Swivel Housing Kit providing a complete overhaul of the front axle swivel assembly for one side, supplied complete with the swivel housing ball. T...

Hex-Head Bolt with a 7/16" UNF (Unified National Fine) imperial thread and a 2" shank length. A fastener used in the manual steering box mounting ...

Bolt with a 3/8" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing applic...

Bolt with a 3/8" UNC (Unified National Coarse) imperial thread and a 2" shank length. A hex-head fastener used in body, chassis and general assemb...

Bolt - M12 x 60mm is a metric hexagon head bolt used across a wide range of assembly applications on Land Rover vehicles. Thread specification M12...

Bolt - M10 x 130mm is a hex-headed metric fastener with a 10 mm nominal thread diameter and a 130 mm shank length. It serves as a general mounting...

heavy duty spring front RR/disco pair, like DA4201 and TF014.

Polyurethane Suspension Bush Kit A complete polyurethane bush set that replaces the original rubber suspension bushes across the chassis-mounted su...

Locking Wheel Nut Set for alloy wheels that use the original alloy wheel nuts, securing the road wheels against theft. The set includes 5 locking ...

Accelerator Cable for EFI engines - left-hand drive applications. This cable runs from the accelerator pedal to the throttle body, transmitting pe...

Bolt is a 3/8" UNF threaded fastener used in body and chassis structural assembly, securing frame and rear-end structure components.

Anti-Roll Bar is the rear stabiliser bar within the suspension system, mounted transversely across the rear axle. Connected to the suspension thro...