Range Rover Parts

Heater Hose - Outlet returns engine coolant from the cabin heating circuit back to the engine cooling system after it has passed through the heater...

Heater Hose - Inlet carries engine coolant into the cabin heating circuit, feeding the heater matrix that warms air inside the HVAC housing. On th...

Mirror - Manual is a manually-adjusted exterior door mirror. It mounts to the door and is adjusted by hand, without electric operation.

Radiator Core is a replacement copper cooling core for the 300 TDi radiator, supplied as the core only without the top and bottom tanks. It is int...

Clutch Slave Cylinder Repair Kit for the hydraulic clutch release circuit on V8 petrol applications. The clutch slave cylinder is actuated by hydr...

Bolt - 1/4" UNF x 1-1/4" is a UNF hexagon head bolt used in hardware and fixings applications across a wide range of Land Rover vehicles. Thread s...

Blanking Plug - plastic plug sealing a 1-1/4" (32mm) diameter aperture in the rear cross member. Installs into unused or access holes in the bodys...

Locking Nut for the steering linkage, securing the adjustable joint onto a heavy-duty drag link or steering rod. Once the joint is set to the corre...

Brake Pedal Rubber Pad for vehicles with automatic transmission. Fitted over the brake pedal arm in the pedal box assembly, this slip-resistant ru...

Door Lock Actuator Electric actuator in the central door locking system. Mounted within the door, it drives the latch to the locked and unlocked p...

Spring Nut - Metal U-Clip for body panel and electrical component fixings across a range of Land Rover models. This metal U-clip spire nut clips o...

Facia Assembly Fastener - a fastener for mounting the facia assembly to the dash structure. It secures the facia panel in place and is also used t...

Sealing Washer - a sealing washer used at cylinder head and thermostat housing joints within the cooling and lubrication circuit. Fitted beneath a...

Handbrake Expander Assembly for the drum-type transmission (parking) brake mounted at the rear output of the transfer box. The expander sits betwe...

Suppressor Capacitor mounted at the ignition coil as part of the ignition system. It suppresses the radio-frequency interference generated by the ...

Self-Tapping Screw - a No. 6 x 1/2" imperial self-tapping fixing used as a general-purpose fastener throughout the body and chassis. The self-tapp...

Screw for use in Land Rover body, chassis, and hardware applications.

Nutsert - 1/4" UNF is a blind rivet nut (rivnut) with a 1/4" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal or...

Distributor Drive Gear - V8

Steering Valve Ring is a PTFE sealing ring used within the rotary valve of the Adwest power steering box. It seals between the pressure lands of t...

Front Brake Caliper Piston is a 41mm piston that operates in the front brake caliper, part of the braking hydraulic circuit for solid disc brakes. ...

Valve Guide for the Rover V8 cylinder head. Pressed into the cylinder head, the guide supports the valve stem and keeps the valve concentric with ...

Intake Elbow Seal for the 3.5L V8 twin-carburettor petrol engine. The seal sits between the air cleaner intake elbow and the carburettor intake to ...

O-Ring sealing the dipstick tube where it enters the cylinder block on the V8 petrol engine. Fitted around the lower end of the dipstick tube, thi...

Bolt used in the camshaft assembly of the 3.5L V8 petrol engine. Imperial UNF fastener, 7/16" diameter with a shank length of 1 1/8". Supplied as ...

Cylinder Head Bolt - a 7/16" UNC x 2.71" medium-type bolt for the Rover V8, part of the cylinder head fixings. This is the medium-length head bolt...

Cylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...

Bolt rear caliper 7/16" UNF

Washer 577254

Front Caliper Fixing Bolt with 7/16 UNF thread, used to secure the front brake caliper to its mounting bracket. This bolt is a safety-critical fast...

Upper Swivel Pin forming the upper pivot of the front axle swivel housing. The pin bolts to the top of the swivel pin housing and runs in the uppe...

Swivel Pin Housing Shim - 0.010in is a 0.010 in (0.25 mm) shim used to set the bearing preload in the front axle swivel pin housing assembly. Fitt...

Hex Nut - 7/16 UNF fixing nut. Used on the fuel pipe unions of the 3.5L V8 twin-carburettor petrol engine. Also supplied as part of a service kit.

Gearbox Selector Pad for the LT77 five-speed manual gearbox. Fits the 5th gear selector within the selector and yoke assembly, forming the bearing...

Washer - a plain flat washer with a 10.5mm internal diameter, sized for M10 fasteners. It seats under a bolt head or nut to spread the clamping lo...

Tappet Guide (guide only) locates and retains the tappet roller assembly within the engine block, maintaining correct alignment of the tappet as it...

Engine Plug is a core (welch) plug that seals the casting holes in the engine. Fitted to the cylinder block, cylinder head water jacket and inlet ...

Brake Caliper Bolt secures the rear brake caliper to its mounting bracket within the rear braking assembly. It clamps the caliper body in position...

Bolt - 5/16" UNF x 5/8" is a general-purpose hexagon-head set bolt in 5/16 UNF (Unified National Fine) thread, 5/8 inch in length. Used across engi...

Hex Nut

Screw - M6 metric fixing screw, 30 mm long. A general-purpose threaded fastener used to secure body panels, door-frame fittings and other bolted a...

Heater Hose - Coolant Valve is a moulded coolant hose in the heater circuit of the engine cooling system. It connects the heater control (coolant)...

Rocker Assembly Aluminium - LH

Clutch Slave Cylinder Repair Kit - a service kit for reconditioning the hydraulic clutch slave cylinder on the R380 5-speed manual gearbox. The cl...

Automatic Transmission Oil Pump for the 4-speed automatic gearbox, part of the transmission's internal hydraulic system. The pump sits at the fron...

O-Ring sealing the air filter housing to the airflow meter on V8 EFI engines. This O-ring seals the joint between the air filter housing outlet an...

O-Ring for the oil strainer in the ZF 4-speed automatic transmission. This seal fits the oil strainer (the automatic transmission fluid pickup fil...

Pan Head Screw, M6 x 12mm. Metric pan head screw for use across a range of Land Rover body, chassis, and electrical assemblies.