Range Rover Parts

Locking Wheel Nut Key - Code C for removing locking wheel nuts with the Code C drive profile. The key engages the unique recessed socket of the Co...

Locking Wheel Nut Set for alloy wheels, comprising four locking nuts that replace standard wheel nuts to deter wheel theft. Thread size 16 x 1.50;...

Oil Pump Rotor Set - Inner & Outer for the 300TDi engine, fitted to the Defender, Discovery 1, and Range Rover Classic. The oil pump rotor set...

Inlet Valve for the cylinder head valvetrain of the Rover V8 petrol engine (3.5L, 3.9L, 4.0L and 4.6L variants). It seats in the cylinder head inl...

Camshaft Sprocket - GEMS V8 is the timing chain sprocket fitted to the camshaft of the Rover GEMS 4.0L and 4.6L V8 petrol engine. The sprocket is ...

U-Type Spring Nut for the fascia (dashboard) assembly and mounting brackets. Spring-steel clip-on nut that grips a panel edge to provide a captive...

Injector Clip for V8 EFI fuel injection systems, used in the fuel delivery assembly at the intake manifold. This retaining clip secures the fuel i...

Bolt - 3/8" UNC x 1-1/4" is a UNC hex head bolt used in the front axle assembly of Land Rover vehicles. Used to secure the track rod damper bracke...

Synchromesh Ring - inner synchroniser ring for the R380 five-speed manual gearbox. Works within the mainshaft synchroniser assembly to bring the g...

Swivel Recovery Eye Rotating recovery point that bolts through the recovery-point holes in a winch bumper, providing a secure anchor for a shackle ...

Blade Fuse - 25A for Land Rover electrical systems. This 25A blade fuse protects individual circuits in the vehicle fuse box from overcurrent damage.

Fixing Screw used in the flywheel, drive plate and clutch assembly. It is one of the threaded fasteners securing the flywheel or automatic drive p...

ABS Sensor Bush is a retaining bush used to locate the wheel speed sensor within its mounting point in the hub or axle assembly. The bush provides...

Dowel used for the precise location and alignment of the front cover to the cylinder block on Rover V8 engines. These dowels ensure the front cove...

Valve Cotter (split collet) for the Rover V8 petrol engine valve train. Locks the valve spring retainer to the valve stem, holding the spring unde...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Throttle Position Sensor (Potentiometer) for V8 petrol engines with Electronic Fuel Injection (EFI). Mounts on the throttle body and signals throt...

Camshaft for the valvetrain of the 4.0/4.6L V8 petrol engine. Mounted in the cylinder block and driven from the crankshaft, the camshaft lobes act...

Camshaft for the Rover V8 EFI petrol engine (3.9L, 4.0L and 4.6L variants). Mounted centrally in the cylinder block, the camshaft is driven from t...

Piston Ring Set - a ring set for one piston of the Rover V8 petrol engine. The set comprises the compression rings and the oil control ring that s...

Ignition Module Link Plug - a 3-to-2 pin adapter plug used with the V8 distributor ignition module. It adapts the wiring connection between a 3-pi...

Sealing Washer - sump plug sealing washer for the ZF four-speed automatic gearbox. Fitted under the head of the transmission sump drain plug, the ...

Tow Slider - Adjustable Saddle Type for the Dixon Bate adjustable tow bracket system. This is the vertically sliding saddle piece in the Dixon Bat...

Bellhousing Gasket for the ZF automatic transmission, sealing the joint between the engine rear face and the transmission bellhousing. It maintain...

Gearbox Sump Gasket for the ZF 4-speed automatic transmission, sealing the joint between the transmission oil pan (sump) and the gearbox casing. T...

Compressor A/C & - TD5 P38 4.6

Towing Jaw rated to 3.5 tonnes, part of the towing/pintle hitch assembly. It provides the jaw coupling for trailer and recovery towing, mounting t...

Hose Clip is a worm-drive (Jubilee-type) clamp with a 20-30 mm clamping range. Tightened by a captive worm screw, it secures a flexible hose onto ...

Crankshaft Main Bearing Cap Cross-Bolt Seal Washer for the Rover V8 petrol engine. This 19mm diameter seal washer seals the main bearing cap cross...

Layshaft Nut for the R380 five-speed manual gearbox. It secures the layshaft gear cluster on its shaft, torqued to specification and then staked in...

Tow Hitch Locking Pin (R-Clip) is the spring-steel retaining clip that secures the tow pin in an adjustable tow hitch. It pushes through the hole i...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Oxygen Sensor (lambda sensor) for the V8 EFI petrol exhaust system on catalyst-equipped applications. It measures residual oxygen in the exhaust ga...

Screw - a No. 8 x 1" self-tapping screw used to secure the wing-top air intake grille. It fastens the air intake grille to the top of the front wi...

Axle Casing Stud for the front and rear axle case assemblies. It is a threaded stud used to secure components to the axle casing on the Land Rover...

Edge Clip - Door Lock Mechanism with various applications across Land Rover Series, Defender, Discovery 1, and Range Rover Classic models. This sp...

oil sump for classic Rover V8 engines

Drive Belt is the serpentine (poly-vee) accessory belt for the 4.0L V8 EFI petrol engine fitted with air conditioning. Driven from the crankshaft ...

PAS pump seal kit

H4 Spare Bulb and Fuse Kit for 12V vehicles with H4 headlamps, holding replacement bulbs for the main exterior lamps and spare blade fuses in a com...

Spark Plug for the ignition system of 2.5L 4-cylinder and 3.5L V8 petrol engines. The plug seals the combustion chamber and carries high-tension v...

Universal Joint for the propeller shaft, measuring 75 mm across the bearing caps with a 27 mm cap diameter. Sealed type, supplied without a grease ...

Cigar Lighter Assembly - facia-mounted 12V cigar lighter, comprising the socket body and the heating element that seats in it. The element is push...

Front Axle Reinforcing Kit - a two-piece set of pre-cut, weld-on reinforcing sections for the front axle casing, profiled to suit the long-nose Rov...

Top Shock Bush Kit - replacement upper mounting bushes for Pro Sport and 8-stage adjustable remote reservoir shock absorbers. The bushes seat in t...

Shock Ball Joint Kit - service kit for the spherical mounting joint at the end of a performance shock absorber. The ball joint is the principal we...

Plain Washer - flat steel washer from the hardware and fixings group. It is fitted under a bolt head or nut to spread the clamp load over the join...