Range Rover Parts

Cylinder Head Dowel for the V8 petrol engine. The dowel is a locating pin fitted to the cylinder block deck that positively registers the cylinder ...

Special Bolt

Grommet - Safety Harness Anchorage

Locking Washer for the swivel pin housing, fitted at the lower swivel pin. Its tab is folded against the retaining bolt to lock the fixing and prev...

Differential Bearing Shim - 0.063in

Thrust Sleeve fits over the front axle half shaft within the constant velocity (CV) joint and swivel housing assembly. It locates between the CV j...

Seal Washer - Swivel Pin Housing is the joint washer that seals the lower swivel pin mounting within the front axle swivel pin housing assembly. C...

Driving Member for the front hub assembly. This splined drive flange bolts to the outer face of the front hub and engages the axle halfshaft, tran...

Swivel Pin Housing Shim used to set the swivel pin bearing preload on the front axle swivel assembly. The shim is fitted at the swivel pin to adju...

Swivel Pin Housing Shim - 0.005in is a 0.005 in (0.13 mm) shim used to set the bearing preload in the front axle swivel pin housing assembly. Fitt...

Swivel Pin Housing Shim (0.003in) used to set the swivel pin bearing preload on the front axle swivel assembly. The shim is fitted at the swivel p...

Flywheel Ring Gear (starter ring gear) for the diesel flywheel, part of the clutch and flywheel assembly. The toothed ring is fitted around the fl...

Differential Shim - 0.060in. Fitted during differential assembly to set bearing preload and gear alignment. Shim thickness is selected against mea...

Differential Pinion Shim - 0.052in. Fitted between the pinion head and its bearing to set pinion depth and preload during differential setup. Shim...

Differential Shim - 0.048in. Fitted during differential assembly to set bearing preload and gear alignment. Shim thickness is selected against mea...

Differential Shim, 0.040in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Differential Shim, 0.038in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Crankshaft Thrust Washer - 0.010in oversize, supplied as a pair. Fitted at the centre main bearing of the four-cylinder engine to control cranksha...

Mudflap Bracket - Front - LH secures the front mudflap to the body on the left-hand side of the vehicle. Part of the front mudflap assembly, the b...

Mudflap Bracket for the front, right-hand side. This bracket secures the front mudflap to the body, holding it at the correct position behind the ...

Door Lock Striker is part of the door locking assembly, mounted on the body aperture at the door pillar. The door latch engages the striker as the...

Gearbox Crossmember - SWB is a weld-on steel chassis crossmember that mounts beneath the gearbox and transfer box assembly, providing structural su...

Halogen Bulb - H4 100/80W (Non-CE). Dual-filament headlight bulb rated 100W high beam and 80W low beam, providing increased light output over the s...

rock slider, rock guards (pair) BA 2091 Generic picture, the set supplied is BLACK coated, NOT galvanised.

Wheel Chock for securing a stationary vehicle. Placed against a tyre, the wedge-shaped chock prevents the vehicle from rolling when parked on an i...

Fuel Tank Inspection Plate Seal is a rubber sealing gasket for the fuel tank inspection plate in the fuel tank assembly. The inspection plate prov...

Locking Wheel Nut Key - Code H, the keyed adaptor that engages the splined pattern of Code H locking wheel nuts. The key is placed over the lockin...

Locking Wheel Nut Key - Code E, the keyed adaptor that engages the splined pattern of Code E locking wheel nuts. The key is placed over the lockin...

Locking Wheel Nut Set - a set of four keyed security nuts, one per wheel, fitted in place of a standard wheel nut to deter theft of the road wheels...

Screw is a fixing screw used to secure exterior lamp, interior lamp and trim components to the body. It retains fittings such as the high-level st...

Gearbox Extension Case Screw for the R380 5-speed manual gearbox. M5 × 30 Torx head screw used to secure the extension case on the R380 gearbox. T...

Retaining Clip used in the parking brake (handbrake) assembly and the automatic transmission gear-change linkage. The clip secures a pivot pin or ...

Dowel is a hollow locating dowel ring that aligns two mating housings during assembly, holding their faces in register and taking shear load off th...

Bulb & Holder - Green, an illumination bulb supplied in its colour-coded green holder for the dashboard and switch panel lighting circuits. Th...

Synthetic Winch Rope - 10mm x 24m - 10,000 lbs for 4x4 winch recovery. This synthetic fibre winch rope is rated to 10,000 lbs (approx. 4,536 kg) b...

Vacuum Advance Unit for the ignition distributor on the 3.5L V8 petrol engine. This vacuum capsule mounts on the side of the distributor and conne...

SRS ECU - the Supplemental Restraint System electronic control unit, commonly known as the air bag control module. It sits at the centre of the SR...

Portable Jump Starter and Air Compressor - a handheld 12V power pack combining a battery jump starter, power bank, tyre inflator and LED work light...

Actuator

Gearbox Bearing for the R380 5-speed manual gearbox, measuring 35 × 72 mm. Fitted within the R380 transmission assembly, this rolling-element bear...

UJ Fitting Kit

Wash/Wipe Column Switch mounted on the steering column, forming part of the windscreen wiper and washer control switchgear. The stalk-mounted swit...

Track Rod Clamp secures the adjustable joint of the steering track rod. Fitted around the split end of the rod, it pinches the threaded sleeve clos...

Fuel Tank Lock Ring secures the in-tank fuel pump and sender assembly to the top of the fuel tank. The ring locks down over the tank aperture, hold...

Air Flow Sensor for the V8 EFI petrol engine management system, mounted in the intake tract between the air filter and the throttle. Measures the ...

Filler Plug is a red anodised aluminium replacement filler plug for the radiator and thermostat housing filler points. Machined from anodised alum...