Range Rover Parts

Suspension Air Valve

Camshaft O-Ring for the 2.5L four-cylinder diesel engines, including the naturally aspirated diesel, turbo diesel and 200TDi. This O-ring forms th...

Silicone Turbo & Intercooler Hose Kit - a three-piece set of silicone charge-air hoses for the 300Tdi turbo and intercooler circuit, replacing ...

Autotec Reverse Light Switch for CDU51/CDU51L manual-gearbox applications. It completes the reverse lamp circuit when reverse is selected. Applica...

Pollen Filter (cabin air filter) for the heating and air conditioning system. It sits in the fresh-air intake ahead of the blower, filtering the ai...

Ball Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...

Pas op alle  V8 benzine motoren met Stromberg carburateurs

Brake Master Cylinder for the brake hydraulic circuit, converting brake-pedal force into hydraulic pressure supplied to the front and rear brake li...

Steering Box is the steering gear at the heart of the power-assisted steering circuit. It converts steering-wheel rotation into lateral movement o...

Front Cover Gasket sealing the timing cover to the front face of the cylinder block on the 300TDi 2.5L turbo diesel engine. It forms the oil-tight...

Clutch Push Rod (9.2 cm) for the clutch release hydraulic circuit, working between the clutch slave cylinder and the release lever. The rod transm...

Flywheel Housing Stud for the 2.5L four-cylinder diesel engine. It secures the flywheel housing to the rear face of the engine, locating the housin...

Jet windscreen wash RRclassic 1986 - 1991

CV Joint Spacer for the front axle drive shaft. Fits on the front halfshaft to correctly space the constant-velocity (CV) joint, setting its seati...

Tailgate End Seal fits to the lower tailgate assembly, sealing the end of the tailgate against the body to keep out water, dust and draughts when t...

Rear Propeller Shaft assembly for the rear axle driveline. Installed between the transfer gearbox rear output flange and the rear differential inp...

Oil Dipstick Tube for the 300 TDi engine, guiding the dipstick down into the sump. Houses and locates the engine oil dipstick, providing the passa...

Crankshaft Pulley Bolt for Land Rover 4-cylinder engines from approximately 1989, used across the Defender, Discovery 1, and Range Rover Classic fi...

Air Suspension Compressor Mount - a rubber isolating mount within the electronic air suspension (EAS) system. It locates the air suspension compre...

Gearchange Housing for the LT77 5-speed manual gearbox. Mounted on top of the gearbox, it carries the gear selector mechanism and locates the gear...

Front Propeller Shaft for the Range Rover Classic driveline. The propeller shaft transmits drive from the transfer box front output to the front ax...

Nut - an M8 x 1.25 captive U-spring nut used to mount the air suspension compressor. The spring-steel body clips over the chassis bracket to provi...

Crankshaft Oil Seal - Front - 300TDi

Rear Brake Pipe Clip retains and locates the rigid brake pipes along the rear of the chassis. It holds the brake lines securely against the chassi...

Finisher Clip - a retaining clip for exterior body finishers and mouldings. The clip secures a trim finisher or moulding to the body panel, engagi...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Spring Nut is an M10 "U"-type spring-steel clip nut that provides a captive threaded fixing point on panels and brackets. The U-shaped clip slides...

Bolt

Coolant temperature transducer for the 3.9L V8 EFI petrol engine, part of the engine management sensing circuit. Threads into the coolant passage ...

Anti-roll bar bush used in the front suspension anti-roll bar assembly, providing the compliant mounting interface between the anti-roll bar and it...

Valve Stem Cap is a hardened cap that sits over the tip of the valve stem in the cylinder head valve train. It forms the wear interface between th...

Front Wheel Bearing Kit for the front hub on vehicles without ABS, fitted with Timken taper roller bearings. The bearings carry the front wheel hu...

Main Bearing Set for the Rover 3.5-litre V8 petrol engine. These are the replaceable shell bearings that carry the crankshaft in the cylinder block...

Repair Washer - M10 for use in suspension, axle and body fastening applications. A large-diameter flat washer that distributes the clamping load o...

Alternator Mounting Screw for the Rover V8 petrol engine alternator assembly. This screw secures the alternator to its mounting bracket on the eng...

Front Shock Absorber Bush Kit for the front suspension assembly. Bush kit for the front shock absorber mounting, providing the rubber isolation be...

Radius Arm Bush Kit - Chassis End, Front (Terrafirma). A set of four uprated polyurethane bushes for the front radius arm mountings, replacing the...

Shock Absorber - Front - +2" Travel for the front coil spring suspension system, designed for use with a 2-inch suspension lift. The extended-trav...

Clutch Cover is the pressure plate assembly of the manual transmission clutch, for V8 petrol applications. It bolts to the engine flywheel and cla...

Plastic Washer serves as a spacing and anti-friction washer at the front seat hinge and the rear door check arm pivot. Fitted at the pivot joint, ...

Plain Washer - Large 5/16" is a large plain washer for use with 5/16" fastenings, providing load distribution beneath bolt heads and nuts across La...

Steel Wheel - a 5.5J x 16 inch tubeless welded steel road wheel, finished in black. The rim carries a 35 mm offset (ET35). Its welded tubeless con...

Programmable Wiper Delay Relay is a direct replacement for the standard AMR2341 relay in the front wiper circuit, providing a user-adjustable inter...

Trunnion

Banjo Bolt secures the breather pipe to an axle, gearbox or transfer case housing. The bolt is drilled through its shank and head so that, clamped...

Shock Absorber for the rear coil spring suspension system. This big-bore unit is designed for heavily laden and expedition applications where sust...

Lens side repeater 300TDI white

Oil Cooler Pipe - a rigid pipe in the automatic transmission's oil cooling circuit, carrying fluid between the gearbox and the transmission oil coo...