Range Rover Velar Parts L560

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Oil Filter Element for the 3.0L AJ20 / AJ22 Ingenium six-cylinder engine, fitted in the engine lubrication circuit. The cartridge element seats in...

Magnetic Oil Drain Plug for the engine oil sump on the 2.0L Ingenium (AJ200/AJ20) four-cylinder petrol and diesel engines. The plug seals the drai...

Oil Pump Seal for the V6 diesel engine oil pump assembly, part of the engine lubrication circuit. It seals the oil pump interface to prevent oil l...

Camshaft Position Sensor within the engine management system of the 3.0L diesel engine. This sensor monitors camshaft rotational position and tran...

Exhaust Crossover Pipe carries exhaust gas between the two cylinder banks of the 3.0 V6 diesel engine, routing the outlet of one manifold across th...

Nut - M5 x 12mm is a threaded securing nut with an M5 thread. It is a multi-application fastener used across a range of body, door and electrical ...

Micro Relay is a 20 amp, 4-pin switching relay used within the vehicle electrical system to control a high-current circuit from a low-current signa...

EGT Sensor Exhaust gas temperature sensor in the exhaust and emissions aftertreatment system of the 3.0L V6 diesel engine. It measures exhaust gas...

Throttle Seal for the intake throttle valve housing. It fits at the joint between the throttle body and the intake, maintaining an airtight connec...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Valve - Control

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Exhaust Manifold Gasket seals the joint between the exhaust manifold and the cylinder head, within the exhaust assembly. It contains combustion ga...

Coolant Outlet Connection is part of the engine cooling circuit, forming the sealed outlet junction where coolant leaves the engine on its way to t...

Valve Stem Seal seals the point where the valve stem passes through the cylinder head valve guide, controlling the oil reaching the stem and preven...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Oil Separator for the crankcase ventilation circuit of the 3.0L V6 Diesel engine. Mounted within the crankcase emission control system, the separa...

Window Control Switch for the driver's door, in the double configuration. The switch is mounted in the driver's door armrest and operates the elec...

Idler Pulley for the auxiliary drive belt, 70mm diameter, positioned within the front-end accessory drive system. The pulley guides and stabilises...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Screw - a fastener used to secure exterior body panels and trim, including body mouldings, front and rear bumper assemblies, radiator grille panels...

Exhaust Manifold Gasket - Right-Hand for the 3.0L TDV6 and SDV6 diesel engine, sealing the right-hand cylinder bank's exhaust manifold to the front...

Exhaust Manifold Gasket - Turbo to Manifold for the turbocharger and exhaust manifold assembly on the 3.0L TDV6 V6 diesel engine. This gasket seal...

Exhaust Manifold Nut is an M8 flanged hex nut that secures the exhaust manifold and turbocharger mounting flanges to the cylinder head. The copper...

Wheel Centre Cover fits into the central hub bore of an alloy wheel, concealing the hub and wheel-mounting hardware behind a finished cap that clip...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Exhaust Manifold Stud secures the exhaust manifold flange to the cylinder head within the exhaust assembly. This is a double-ended stud, threaded ...

o-ring oil cooler 3,0 TDV6

Latch hood, bonnet, RH and LH, with sensor

Camshaft Seal for the TDV6 2.7L V6 diesel engine. Seals the camshaft at its exit point from the cylinder head, preventing oil leakage from the cams...

Timing Chain Kit for the Ingenium 2.0L 4-cylinder engine, covering the complete timing chain system. The Ingenium AJ200 engine uses a dual-chain a...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Transmission Oil Pan & Filter Kit - the lower fluid pan for the ZF 8HP70 8-speed automatic transmission, incorporating an integrated fluid filt...

Upper Sump Gasket seals the upper oil sump section against the cylinder block within the engine lubrication system. It provides an oil-tight seal ...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Timing gear lower idler pulley for the engine timing drive system. This pulley guides and stabilizes the timing belt within the lower timing gear...

Crankshaft Locking Tool - 2.0 Diesel AJ200D

Front Crankshaft Oil Seal Fitting Tool - 2.0 Diesel AJ200

Window Regulator Wrench

Oil Pressure Switch for the engine lubrication system on Td6 2.7 and 3.0 diesel engines. The switch is threaded into the engine block and monitors ...

Oil Pressure Switch for the engine lubrication system on Td6 2.7 and 3.0 diesel engines. The switch is threaded into the engine block and monitors ...

Camshaft Cover Gasket - sealing gasket between the camshaft cover and the cylinder head face, for 2.7L Td6 and 3.0L V6 diesel engines. The gasket ...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...