Products

Cable Grommet for the wiring loom, fitting a 41.5 mm panel hole and accepting a cable of up to 6 mm. Made of black rubber, it lines the hole where...

Grommet / Blanking Plug - Dash Bulkhead for Land Rover Defender. This rubber plug seals an unused aperture in the dash bulkhead (such as a heater ...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Bonnet Latch for the bonnet (hood) closure mechanism. It engages the bonnet striker to hold the bonnet closed and releases it when operated, formin...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Drive Fastener - black plastic drive-in retaining clip used to secure body mouldings, trim panels and interior finishers to their mounting panels. ...

O-Ring and Grease Kit for servicing the transfer box input shaft. Contains the input shaft O-ring and the anti-seize grease used when resealing th...

Brake Disc & Caliper Bolt - a fixing bolt for the brake disc and caliper assembly. It is used at both the front and rear brake disc and calipe...

Expansion Tank Seal - sealing ring for the bleed valve fitted to the coolant expansion tank in the engine cooling system. Seals the bleed valve in...

Exhaust Clamp - 60mm exhaust joint clamp for the front section of the exhaust system, securing the downpipe to the centre silencer section. Clamps...

Timing Gear Bolt from the engine timing drive, securing the camshaft sprocket and variable camshaft timing adjuster to the camshaft. It provides t...

Crankshaft Sprocket Washer from the engine timing drive, fitted at the front of the crankshaft beneath the drive sprocket retaining bolt. It sprea...

Valve Spring Retainer from the cylinder head valve train, the top cap that closes off the valve spring. It sits on top of the valve spring and is ...

Crankshaft Front Oil Seal for the timing gear cover, sealing the crankshaft nose where it passes out through the front cover. It runs on the crank...

Gasket - Oil Filter to Block seals the joint between the oil filter housing and the cylinder block, within the Oil Cooler and Filter assembly. It ...

Gasket - Oil Cooler seals the engine oil cooler to its mounting face, within the Oil Cooler and Filter assembly. It maintains the integrity of the...

Camshaft Cover Gasket - LH seals the left-hand camshaft cover to the cylinder head on the AJ133 5.0L V8 petrol engine. It closes the joint around ...

Water Manifold Gasket for the engine cooling and heater circuit - it seals the water manifold tube where it leaves the cylinder block and feeds the...

O-Ring for the engine cooling system - it seals the water outlet tube at its connection to the cylinder block, alongside the thermostat housing. T...

Inlet Valve - cylinder head inlet (induction) valve for the 5.0L V8 AJ133 supercharged petrol engine. The inlet valve admits the intake charge int...

Crankcase Breather Tube - a hose in the crankcase emission control (crankcase ventilation) system on petrol engines. The tube routes blow-by gases...

Cam Cover Gasket for the right-hand cylinder head of the 5.0L AJ133 V8 petrol engine, part of the camshaft cover assembly. The gasket seals the jo...

Blanking Plug used within the engine cooling system - thermostat housing, radiator and coolant expansion tank, and the cooling pipework. The plug ...

Pin, 6 x 36mm, from the timing gear and auxiliary drive assembly of the 5.0L AJ133 V8 petrol engine. It serves as the guide pin for the auxiliary ...

Screw, M6 x 38mm, from the timing gear assembly - timing chains, tensioners and guides, and the auxiliary drive. It retains the chain guide in pos...

O-Ring for the oil pump inlet tube, part of the oil pump, sump and filter assembly. It seals the joint at the oil pump inlet (pick-up) tube, keepi...

O-Ring for the oil pump outlet tube, sealing the pressurised feed within the oil pump, sump and filter assembly. The outlet tube carries oil from ...

Spark Plug Aperture Gasket for the right-hand camshaft cover, sealing the spark plug well against oil ingress. The camshaft cover carries a tube f...

Oil Filter - the replaceable cartridge element for the engine lubrication circuit, fitted inside the filter housing on the oil pump, cooler and fil...

Pulley - Fan

Intercooler to Inlet Manifold Gasket from the charge air induction system of the supercharged 5.0L V8 petrol engine (AJ133). The supercharger and ...

Valve Cover Screw and Sleeve from the cylinder head cover fixings of the petrol V8 and supercharged V6 engines. The screw secures the camshaft (va...

Valve Cover Stud and Sleeve from the cylinder head cover fixings of the petrol V8 and supercharged V6 engines. The stud threads into the cylinder ...