Products

Sidelight Bulb, rated 24V 10W, for the front sidelight (parking light) position. The bulb seats in the sidelight holder within the front lamp asse...

Halogen Bulb - H4 100/80W (Non-CE). Dual-filament headlight bulb rated 100W high beam and 80W low beam, providing increased light output over the s...

Oil Drain Plug threads into the drain port at the base of the engine sump, sealing the oil pan against leakage during operation. It sits within the...

Accelerator Pedal Pad - a moulded rubber pad fitted over the accelerator pedal arm, providing a textured grip surface for the driver's foot and pro...

Sealing Washer for diesel fuel injectors, positioned at the injector nozzle seat in the cylinder head to seal against combustion gases around the i...

Clutch Cylinder Adaptor - a pipe union that connects the hydraulic clutch supply pipe to the inlet port of the clutch master cylinder. Fitted at t...

Cable Tie is a harness fixing used to bundle and route wiring looms, hoses and cables against the chassis and body. It secures the harness in posi...

Brake Drum Screw for the brake drum assembly. This retainer screw secures the brake drum to the wheel hub flange, preventing the drum from displac...

Braided Earth Strip is a flexible braided conductor that forms an electrical earth (ground) bond between two points in the vehicle. It provides a ...

Mainshaft Bearing for the gearbox mainshaft - the centre bearing that supports the mainshaft within the gearbox casing. It locates and carries the...

Caliper Seal - internal bridge seal for the front brake caliper. This O-ring sits between the two halves of the caliper body and seals the fluid pa...

Brake Servo Repair Kit for the Type 50 vacuum brake servo unit (227mm diameter). This overhaul kit contains the components necessary to rebuild th...

Valve repair kit

Lights and Heater Switch - a three-position Lucas-type toggle switch fitted to the dashboard switchgear. It acts as the master control for the exte...

Corner Filler is an exterior body panel that closes the rear corner of the door aperture, bridging the gap between the door assembly and the surrou...

Corner Filler - Front trim piece for the front door window channel. It fits to the front corner of the front door, filling and finishing the join i...

Glazing Rubber Seal for retaining glass panels in fixed window aperture frames. This flexible rubber channel seal locates in the groove of the win...

Sump Plug Sealing Washer for the engine lubrication system. It seats between the oil drain plug and the sump pan boss, sealing the joint so the plu...

Track Rod End Boot for the steering track rod end ball joint. This rubber boot fits over the track rod end housing, sealing the ball joint against...

Track Rod End Boot Ring - spring retaining ring for the track rod end of the steering linkage. It clamps the rubber dust boot onto the track rod en...

Brake Clevis A clevis for the brake drum expander mechanism within the drum braking system. It forms the pinned link between the brake operating r...

Clevis Pin - pivot pin used in the mechanical brake and transmission linkages. It passes through a forked clevis and the eye of a mating rod or lev...

Circlip - Output Shaft Flange used within the transfer box output flange assembly to retain the output shaft bearing and associated components in p...

Double-Grooved Ball Bearing for the manual gearbox and transfer box. It supports and locates a rotating shaft within the casing, carrying the radia...

Axle Key Washer for the hub nut locking system in the axle assembly. This tab washer seats beneath the axle hub nut, with tabs that locate into ma...

Outer Hub Lock Washer for the front and rear hub assembly on Land Rover solid axles. This lock washer secures the hub bearing retaining nut agains...

Lock Washer for the gearbox mainshaft, securing the special retaining nut where the mainshaft meets the transfer box. A tab washer whose tang is b...

Output shaft bearing

Bolt for the LT76 gearbox assembly, with a 5/16" BSF (British Standard Fine) thread. Used as a threaded fastener within the gearbox casing.

Gearbox Crossmember - SWB is a weld-on steel chassis crossmember that mounts beneath the gearbox and transfer box assembly, providing structural su...

Brake Shoe Spring for the drum brake assembly on Land Rover vehicles. This return spring pulls the brake shoes back from the drum face after each ...

Washer for Land Rover applications.

Instrument Bulb - 12V 2.2W for the instrument panel. Replacement dial illumination bulb for the speedometer on Range Rover Classic Police Vehicle ...

Grommet seals and protects cables, harnesses and hoses where they pass through body and chassis panels. It is used at wiring harness pass-throughs...

Grease Nipple with a short thread, used at propshaft universal joint lubrication points. The nipple threads into the grease point and provides the...

Drain Plug for the axle casing and fuel tank. This brass threaded plug seals the drain aperture at the bottom of the differential and axle casing,...

Swivel Ball Seal Retainer for the front axle swivel housing. This retaining ring clamps the swivel housing oil seal against the swivel ball, holdi...

Timing Chain Idler Wheel runs against the timing chain within the front timing case, guiding the chain and helping maintain its tension between the...

Drain plug

Differential flange 4-spline

Brake Shoe Anchor Plate for the rear drum brake assembly. The anchor plate provides the fixed abutment and locating point for the brake shoes. It ...

Lock Plate for the rear drum brake shoe retainer. This fold-over tab plate locks the two screws that secure the brake shoe bottom retainer ring. I...

Bolt - 3/8" BSF x 1" hexagonal head bolt to British Standard Fine thread specification. 3/8" BSF (British Standard Fine) thread with a 1" shank le...

Split Pin locks slotted nuts, clevis pins and linkage joints against loosening, passing through a drilled hole and splayed to retain the assembly. ...

Exhaust Clamp Plate for the exhaust mounting assembly. Three-hole clamping plate that secures the exhaust pipe within the mounting bracket assembl...

Exhaust Bracket for the exhaust system on left-hand drive vehicles. This bracket supports and locates the exhaust along its run beneath the vehicl...

Exhaust Clamp for the exhaust-to-chassis mounting. Two-bolt upper clamp plate that forms the exhaust-to-chassis mounting assembly on Series and ea...