Products

Piston Ring Set for the 2.25L and 2.5L 4-cylinder petrol engine, supplying the ring pack for one piston. The rings seat in the piston ring grooves...

Piston for the 3.5L V8 petrol engine, standard (nominal) bore size. It reciprocates within the cylinder bore, transmitting combustion pressure thr...

Piston for the 3.5L Rover V8 petrol engine, supplied at +0.020" oversize with an 8.13:1 compression ratio. The +0.020" oversize suits a rebored bl...

Clutch Driven Plate for the V8 clutch assembly. It is carried on the gearbox input shaft between the flywheel and the clutch cover (pressure plate)...

Fuel Tank Mount is a rubber mounting that supports the fuel tank on the chassis. It cushions the tank on its mounting bracket, isolating it from c...

Air Intake Hose for the 2.25 litre diesel engine, forming part of the air induction system between the air cleaner and the intake manifold. It car...

Cam Follower (tappet) in the valvetrain, riding on the camshaft lobe to transmit its motion to the pushrod and valve. It converts the rotating cam...

Fuel Filter for the diesel fuel delivery system, separating dirt, debris and water from the fuel before it reaches the injection pump. Fitted in t...

Oil Pressure Switch for the engine lubrication system warning circuit. This pressure-sensitive switch threads into the engine block oil gallery an...

Brake & Clutch Master Cylinder - Combined CV-Type serves both the braking and clutch hydraulic circuits from a single unit. In this CV-type de...

Brake Master Cylinder for the braking hydraulic system, converting brake pedal force into hydraulic pressure to actuate the brakes. Mounted to the...

Heater Hose – Inlet carries hot coolant from the engine cooling circuit to the heater matrix, forming part of the cabin heating system. The inlet ...

Retainer for the steering damper mounting, part of the track rod and steering damper assembly. This stem washer locates on the steering damper mou...

Exhaust Clamp Plate for the exhaust system, used at the front-pipe and catalyst joint. The plate works together with a U-bolt to draw the exhaust c...

Bolt – 3/8" BSF x 1-1/4" is a threaded fastener used in the front axle assembly, securing the swivel pin housing. The bolt has a 3/8 inch diameter...

Spring Shackle connecting the end of a leaf spring to the chassis bracket, allowing the spring to lengthen and shorten as it deflects under load. ...

Shackle Plate, the side plate of the spring shackle assembly that forms the swinging link between the leaf spring eye and the chassis shackle brack...

Woodruff Key that locates the timing gear and pulley on the crankshaft of the Rover V8 petrol engine. The key sits in the crankshaft keyway to pos...

Oil Pump Relief Plunger is the pressure-relief valve plunger within the engine oil pump, part of the lubrication system on the 3.5L V8 petrol engin...

Pinion Lock Nut – Salisbury secures the drive pinion in the Salisbury rear differential, retaining the pinion flange and holding the pinion bearing...

Fuel Hose for the 3.5L V8 twin-carburettor engine, part of the carburettor fuel supply plumbing. It connects the fixed points in the fuel feed lin...

Oil Seal – Rear Output Shaft seals the rear output shaft of the LT95 combined gearbox and transfer box, preventing oil leakage where the shaft exit...

Steering Relay Gasket seals the steering relay assembly within the steering linkage. The steering relay transfers movement from the steering box d...

Circlip

Blanking Plug fills an unused switch aperture in the dashboard switch panel. Where a fascia switch position is not fitted, this plug closes off th...

Heater Matrix is the compact coolant-to-air heat exchanger at the core of the cabin heating circuit, housed within the heater box behind the dashbo...

Brush set M418G

PDWA Switch (Pressure Differential Warning Actuator) is part of the brake hydraulic circuit, bridging the two independent front and rear pressure l...

Speedo drive oil seal LT230

Carb overhaul kit 175CD V8 Zenith Stromberg

Sedimentor Seal for the diesel fuel sedimentor assembly. The sedimentor separates water and sediment from the fuel ahead of the injection system. ...

Sedimentor Sealing Ring for the diesel fuel filter and sedimentor assembly. The sedimentor separates water and sediment from the diesel fuel befor...

Self-Tapping Screw - a No. 8 x 3/8" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as it ...

Self Tapping Screw for use in Land Rover body, chassis, and hardware applications.

Self-Tapping Screw – No. 8 × 5/8 in is a general-purpose fastener for securing body, trim and panel fixings. Being self-tapping, it forms its own ...

Tap screw

Grille Screw – Black secures the front grille panel to its surrounding bodywork. The black finish matches the grille and adjacent trim, giving a d...

Platform Assembly - the front bonnet-locking platform of the front-end bodywork. It carries the grille aperture and the bonnet locking mechanism, a...

Power Steering Pump Seal Kit – Cast provides the seals needed to overhaul the cast-bodied power steering pump within the steering hydraulic circuit...

PAS Pump Gasket Set is the set of gaskets and seals used to reseal the power steering pump during overhaul. It renews the static sealing joints of...

Self-Tapping Screw, size No. 6 x 3/8", for the door glass and window regulator assembly. This screw secures the window glass run channel to the do...

Drive Screw - a No. 6 x 1/2" self-tapping drive screw used across door and facia assemblies. It secures the front door glass and window regulator,...

Dashboard Screw for facia and dash trim fixing - a No.6 x 3/4" countersunk self-tapping screw. Used to secure dashboard and facia trim panels. The...

Screen Washer Pump for the rear window wash circuit. This electric pump draws washer fluid from the reservoir and delivers it under pressure to th...

Seat belt bracket RH

Seat Belt Bracket provides the upper shoulder belt anchorage point in the front seat restraint system. Fitted to the left-hand side, it secures th...