Products

Spare Wheel Carrier Clamp Plate secures a bonnet-mounted spare wheel to its carrier. The plate clamps against the wheel to hold it firmly on the c...

Fuel Tank Sender Locking Ring for the fuel tank sender unit assembly. This ring secures the fuel level sender unit in position within the fuel tan...

Radiator Grille Frame - With Air Conditioning for the Defender. Structural front-end panel that carries the radiator grille and defines the air in...

Bulkhead Vent - Open - LH - the left-hand (near side) hinged vent lid set into the bulkhead, forming part of the fresh-air ventilation system. Whe...

Bulkhead Vent - Open - RH - the right-hand (off side) hinged vent lid set into the bulkhead, forming part of the fresh-air ventilation system. Whe...

Bonnet Release Cable is the Bowden control cable that links the in-cab release lever to the bonnet latch mechanism. Pulling the release lever draw...

Bonnet Stay Bracket - mounting bracket for the bonnet stay. Locates and supports the bonnet stay, holding the bonnet in the open position for engi...

Bonnet Stay Bracket is the left-hand mounting bracket for the bonnet stay. It forms the pivot-bush end of the bonnet stay assembly, providing the ...

Sill Panel Stay is a support bracket for the sill (rocker) panel. Forming part of the sill panel assembly, it braces the sill panel to the body st...

Air Intake Finisher is the wing-top grille that covers the cold air intake aperture of the induction system. This is the right-hand wing-top finis...

Air Intake Grille is the louvred wing-top panel that covers the cold-air inlet at the base of the windscreen. Mounted on the left-hand wing top, i...

Air Intake Blanking Plate closes off the right-hand wing-top air-intake aperture where a cold-air inlet is not required. It fits the same opening ...

Air Intake Blanking Plate closes off a wing-top air intake aperture in the induction system. This is the left-hand wing-top blank for left-hand-dr...

Radio Cassette Housing for the Defender 90/110 dashboard interior trim assembly. This moulded trim housing surrounds and retains the radio cassett...

Bonnet Insulation Pad for the engine bay sound-and-heat insulation system. Fits to the underside of the bonnet, where it dampens engine noise tran...

High-Mounted Stop Lamp Stud is a mounting stud for the high-level stop lamp. It secures the high-level (centre) stop lamp to its mounting point on...

Seat Squab is the backrest section of the right-hand front seat assembly. The squab forms the upright cushion against which the occupant's back re...

Seat Base Cushion - Front for the front seat assembly. This cushion forms the lower seating surface and mounts onto the front seat frame, supporti...

Instrument Panel Finisher is the moulded trim panel that frames the instrument binnacle on the dashboard. It fits over the facia around the instru...

Facia Finisher (RHD) - the trim finisher strip that runs along the top of the dashboard facia, from the instrument binnacle across to the passenger...

Heater Hose - Inlet for the engine coolant and cabin heater circuit on the Td5 2.5L 5-cylinder turbo diesel. Carries hot coolant from the engine f...

Heater Hose is a coolant hose in the heater circuit of the Td5 2.5L 5-cylinder turbo diesel. It carries engine coolant between the cooling system ...

Special Fixing Washer for the hardtop side-frame mounting. Seats over the M8 side-frame mounting stud and under its securing nut, spreading the cl...

Bulkhead Mounting Bolt - M12 x 180mm fastener securing the lower bulkhead to the chassis. Forms part of the body-to-chassis mounting at the base o...

Mounting Stud is a threaded fixing used in the rear body upper fixings. It is an M8 stud, 67 mm in length, providing a fixed threaded mounting poi...

Body Panel Stud is a threaded fixing used in the cab and rear body panel mounting hardware. It provides a fixed anchor point for securing body pan...

Screw - No. 10 x 1 in. Secures the instrument binnacle cowl and interior air-deflector trim. Sized for self-tapping installation into moulded trim...

Bush is a body mounting bush used in the rear body upper fixings. It fits at the fixing point between the body and its mounting, setting the corre...

Rear Lamp Guards - a pair of slatted steel guards fitted over the rear lamp assemblies to protect the lenses and lamp bodies from stone chips, bran...

Spare Wheel Cover - a soft cover that fits over an externally mounted spare wheel to shield the tyre and rim from dirt, road grime, moisture and UV...

Spare Wheel Cover fits over an externally mounted spare wheel to protect the tyre and wheel from weather, road dirt and UV exposure. This is the h...

Rock Guards - exterior body protection that mounts along the lower sill line to shield the sill panels and lower bodywork from impact damage during...

Differential Guard - a wrap-around steel guard that shields the front or rear differential housing from impact and debris during off-road use. Des...

Battery Isolator Switch - key-operated master cut-off switch for the vehicle electrical system, rated at 300A. Wired inline on the main battery le...

Cup Holder for the BA 189A centre cubby box. This is the replacement cup holder component for the current-design cubby box, providing a secured rec...

Wading Kit for the drivetrain and engine breather system, extending the breather points of the axles, gearbox and engine to a higher level. Raisin...

Rear Coil Springs for the rear suspension, raising ride height by approximately 50mm over standard. Supplied as a pair. The raised height increase...

Silicone Turbo Hose Kit - a set of reinforced silicone hoses that replace the original charge-air (boost) hoses in the turbocharger and intercooler...

Spring Retaining Plate Front coil spring retaining plate that clamps over the top of the spring at its seat, holding the spring captive so it canno...

Gear Knob is a machined aluminium knob that fits the top of the manual gear lever. It threads onto the gear lever of the LT77 five-speed manual ge...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...