Products

Transfer Box Flange Bolt - a 3/8" UNF x 1-1/4" hex-head bolt for the LT230 transfer case front output flange. It secures the drive flange to the f...

Radiator with Integrated Oil Cooler - the main engine cooling radiator for the 200 TDi diesel engine, incorporating a built-in engine oil cooler an...

Radiator Core is a replacement copper cooling core for the 300 TDi radiator, supplied as the core only without the top and bottom tanks. It is int...

Gear Lever Gaiter - rubber gaiter fitting over the gear lever and transfer box lever at the transmission tunnel diaphragm panel, sealing the tunnel...

Rear Mudflap - exterior splash guard that mounts behind the rear wheel to deflect mud, water and road debris away from the underbody and following ...

Rear Mudflap - exterior splash guard that mounts behind the rear wheel to deflect mud, water and road debris away from the underbody and following ...

Heater Return Hose moulded coolant hose within the heater circuit, carrying coolant from the heater matrix back to the engine cooling system. Shap...

Seat Belt - Rear Centre Lap - Long End for the rear seat belt assembly in the Defender passenger compartment. This is the long webbing end of the ...

Heater Hose - coolant return hose in the heater circuit for the 300 Tdi engine. It carries coolant on the return path from the heater matrix back ...

Inlet Heater Hose - 300TDi - RHD

Air Intake Grille Panel - air intake grille installed within the air intake system housing, forming part of the intake ducting assembly upstream of...

Window Regulator Escutcheon - trim finisher that locates over the manual window winder spindle on the inner door, concealing the regulator aperture...

Headlamp Surround Finisher - Left-Hand - black trim bezel that frames the headlamp on the front panel, surrounding the headlamp unit and locating a...

Headlamp Surround - Right-Hand - trim finisher that frames the headlamp on the front panel, surrounding the headlamp unit and locating against the ...

Floor Mat is a moulded rubber footwell mat shaped to fit the left-hand floor over the gearbox tunnel. The foam backing adds sound insulation under...

Floor Mat is a moulded rubber footwell mat shaped to fit the right-hand floor over the gearbox tunnel. The foam backing adds sound insulation unde...

Cvr Floor Front R

Heater Inlet Hose carries hot coolant from the engine to the inlet side of the heater matrix. Part of the heater coolant circuit, it feeds the mat...

Heater Distribution Control Cable - the Bowden cable that links the dashboard heater control to the air-distribution flap in the heater assembly. ...

Demister Outlet Finisher - vent finisher set into the top of the dashboard over the windscreen demister outlet, directing heated and ventilated air...

Door Trim - Rear Casing - Slate Grey for the Defender rear end door interior. This rear door casing panel fits the interior face of the Defender r...

Caliper Bolt is the fixing bolt that secures the brake caliper to its mounting bracket. The same bolt specification is used across several chassis...

Hexagon Bolt - an M10 x 45 mm high-tensile bolt, property class 10.9, used in the suspension top link, fulcrum and ball joint assembly. The 10.9 g...

Link Clip - an anti-rattle clip for the side door latch linkage. It retains the latch operating rod within the door lock mechanism, holding the li...

Tailgate Cable is a retaining cable for the drop-down rear tailgate on pick-up bodies. It links the rear body panel to the tailgate and limits how...

Lock Nut from the rear end-door grab handle assembly on the Defender. This lock nut secures the grab handle fitted to the rear end door. One nut p...

Castor Correction Kit - 44mm Wide Bush for the front suspension radius arm assembly on the Defender, Discovery 1, and Range Rover Classic. Lifting...

Rear Mud Flap Bracket in stainless steel. This bracket mounts the rear mud flap to the vehicle, holding it in position behind the rear wheel. Made...

Stainless Bracket Only - Defender 110 130

Mud Flap Bracket for the left-hand rear position on High Capacity Pick Up (HCPU) bodywork. Part of the exterior mud flap mounting. The HCPU rear b...

Circlip a spring-steel retaining ring that seats in a machined groove to axially locate a component on a shaft or within a bore. Used in the diffe...

Circlip Retaining circlip for the gearbox rear output shaft. It seats in a machined groove on the output shaft, locating the adjacent component ax...

Front Door Glass Channel Assembly is the run channel that guides the front door window glass within the door frame. It forms part of the front doo...

Glazing rubber

Hose Clip - 12-20mm worm-drive hose clip suitable for hoses with an outside diameter of 12 to 20mm. This stainless-steel screw-type clip tightens ...

Hose Clip is a worm-drive band clamp used to secure flexible rubber hoses onto rigid pipe spigots and unions across the coolant, heater, fuel and i...

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...

Hose Clip - Jubilee - 70-92mm is a worm-drive band clamp with a clamping range of 70-92 mm. It secures a hose over its spigot or connector, compre...

Sliding Window Catch Fixing Block mounts within the upper-cab sliding side window assembly. It provides the anchor point that secures the sliding ...

Wing Mirror Assembly is a complete manually-adjusted exterior door mirror, supplied as a single unit comprising the mirror head, mounting arm and g...

Brake Pipe Clip - single-bore retaining clip for securing a rigid brake pipe to the chassis or body structure. This clip holds the brake pipe in i...

Brake Union Nut - Metric Thread for the hydraulic brake pipe circuit. This union nut seals and secures brake pipe connections at the unions throug...

Steering Wheel Nut - 1/2" UNF is the hex retaining nut that secures the steering wheel to the splined steering column shaft. Threaded 1/2" UNF, it...

Exhaust Olive is a tapered sealing ring used at the exhaust system's pipe joints. It seats between two pipe sections at a compression joint, formi...

Interior Rear-View Mirror for the Defender cab, using the click-fit mounting system. Attaches to the windscreen-bonded base bracket via a click-fi...

Window Regulator for the right-hand front door, electric type, supplied complete with motor. Part of the door window mechanism. The regulator carr...