Products

Pedal Shaft is the transverse shaft on which both the clutch pedal and brake pedal are mounted within the cab, on vehicles without a brake servo. ...

Banjo bolt

Manifold Gasket for the 2.25L and 2.5L 4-cylinder petrol engines. This gasket seals the combined inlet and exhaust manifold assembly to the cylind...

Handbrake Drum is the drum for the transmission-mounted parking brake, for use with the LT76 gearbox. Mounted at the rear of the gearbox on the tr...

Rocker Cover Gasket for the 2.6L six-cylinder petrol engine, sealing the side rocker cover to the cylinder head. It forms the oil-tight joint alon...

Timing Chain Vibration Damper for the front timing chain drive on four- and six-cylinder engines. Mounted within the timing cover, it bears agains...

Fuel Pump Gasket for the 2.0L diesel engine (Series II) and 2.25L diesel engine (Series IIA). This gasket seals between the mechanical fuel pump b...

Oil Feed Pipe is the external oil feed pipe supplying the cylinder head within the engine lubrication system. It carries pressurised oil from the ...

Propshaft Gaiter with Clips for the front propshaft sliding joint. This rubber gaiter fits over the splined sliding joint (slip yoke) of the front...

Timing Chain Tensioner maintains correct tension on the timing chain within the engine timing case, preventing chain slap and ensuring accurate val...

Carburettor Spacer for the petrol engine induction system, fitting between the carburettor and the inlet manifold. It sets the carburettor off the...

Carburettor Manifold Gasket for the 2.25L petrol and carburettor-equipped Defender engines. This gasket seals at the interface between the carbure...

Brake & Clutch Pedal Pad for the foot pedal assembly. This moulded rubber pad fits over the brake and clutch pedal arm, providing the grip surf...

Nut with a 5/16 inch BSF (British Standard Fine) thread. A hexagonal fastener that threads onto a matching 5/16 inch BSF bolt or stud to secure a ...

Cleat Rope Hook Body Side All and Classic (Softtop) - Series Defender

Weatherstrip for the alpine light (side roof window) glass. This rubber sealing strip retains and seals the 5mm glass panels of the alpine lights ...

Gaiter Retainer - secures the rubber gaiter around the high-low (transfer) lever on the LT76 gearbox, which carries an integral transfer box. The ...

Tailgate Seal for the lower edge of the rear tailboard. It seats along the bottom of the drop-down tailgate and seals against the body, keeping wa...

Hoodstick Bracket Clamp - secures a hoodstick to its mounting bracket within the soft-top frame. The clamp holds the hoodstick (the soft-top frame...

Body Mounting Shim used to set the correct clearance and alignment between the body tub and the chassis mounting points. This thin flat shim is us...

Rear Quarter Seal - the rubber glazing seal that secures the fixed rear quarter window into the hard-top body aperture. Sized for 5mm glass, it be...

Door Clevis Pin for the door check strap mechanism. The pin locates the check strap to its mounting bracket, forming the pivot the strap works aga...

Spring Washer for the fuel tank sender unit and fuel pick-up pipe fixings. Fitted beneath the retaining screws that secure the fuel gauge sender u...

Floor Panel Screw with a mushroom head profile, used to secure floor plates and lower rear body panel assemblies on the Defender. The low-profile ...

Lower Tailgate for the rear of the body - the drop-down tailboard panel that closes off the rear of the load area. Hinged along its lower edge, it...

Barrel Lock and Key, Set of Two for the door locks, supplied as two keyed lock barrels each with a key. Each barrel is the cylinder the key turns ...

Barrel Lock and Key, Set of Three for the door locks, supplied as three keyed lock barrels each with a key. Each barrel is the cylinder the key tu...

Bench Seat Backrest in black vinyl, forming the upright back section of the folding rear load area bench seat. This 810mm wide backrest mounts to ...

Bench Seat Backrest in techno fabric, forming the upright back section of the folding rear load area bench seat. This 810mm wide backrest mounts t...

Bench Seat Cushion - Techno Trim for the rear inward-facing bench seat. This is the fixed rear bench cushion that forms the seating surface of the...

Front Outer Seat Cushion Base for the adjustable seat frame in Series II, IIA, and III 109" long-wheelbase vehicles. This is the outer seat base c...

Inner Seat Base is the centre front seat base cushion, forming the lower seating platform of the basic vinyl front seat. Finished in black vinyl f...

Rear Folding Bench Seat - a complete rear bench seat assembly that folds to free up the load area when not in use. Finished in black vinyl, which ...

Rear Bench Seat Assembly in grey vinyl, comprising a cushion, backrest, frame, and fitting kit for direct installation in the rear load area. The ...

Rear Seat Assembly - a two-seater rear bench seat upholstered in grey twill vinyl, for the rear passenger area of Defender and Series Land Rover ve...

Rear Folding Bench Seat - a complete rear bench seat assembly that folds to free up the load area when not in use. Finished in Techno-style uphols...

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Drain Plug - a tapered threaded plug used to seal and drain fluid from engine and driveline housings. It serves as a coolant drain plug in the cyl...

Swivel Ball Taper Plug for the front axle swivel housing. This tapered-thread plug screws into a port in the swivel ball housing, sealing it agains...

Rubber Buffer for the door-top sliding side window. The buffer fits at the top of the door and acts as an end-stop for the sliding glass, limiting...

Tailgate Chain Cover - a pair of protective sleeves that fit over the two retaining chains supporting the rear tailgate. Each chain links the tail...

Front Outer Wing Panel - Aluminium - Left Hand Side for Series Land Rovers. This aluminium outer wing panel replaces the front left wing skin on S...

Hook for the soft top retaining rope, part of the hood and hoodstick assembly. Secures the rope that runs along the soft top drain channels.

Front Rope Retaining Hook - Left Hand Side for the soft-top hood system on Series and Defender Land Rovers. This hook is part of the hoodstick and...

Hinge Pin Kit containing the replacement hardware for door and rear tailgate hinges on Series and early Defender models. Fits the front and rear d...

Floor Mat Retainer secures the intermediate second-row rubber floor mat. Holds the mat in position against movement underfoot.

Leather hasp civilian

Tailgate Buffer - rubber buffer for the rear tailgate (tailboard). This rubber buffer cushions the tailgate where it meets the body, absorbing the...