Products

Pillar seal

Window Seal - a rubber glazing seal that beds the window glass into its body aperture, sealing the joint against water and draughts.

Sliding Window Catch secures the sliding glass of the front door side window, locking the two panes together so the window can be held shut or fixe...

Tailgate Hook for the lower hinged tailboard, right-hand side. This pigtail (spiral) hook mounts on the body and retains the tailgate support stra...

Tailgate Hook for the lower hinged tailboard, left-hand side. This pigtail (spiral) hook mounts on the body and retains the tailboard chain, holdi...

Fitment: all models to 1980

Floor Mounting Pad is a 5mm rubber spacer pad used at the rear body floor support mounting, fitted between the body and the chassis-mounted support...

Bonnet Buffer - rubber buffer at the bulkhead. This rubber buffer mounts at the bulkhead where the rear of the bonnet rests when closed, cushionin...

Glass Retainer is the vertical glazing retainer for the rear end door assembly. Holds the rear door glass along its vertical edge.

Check rod RH

Corner Capping - galvanised - right-hand (offside) roof corner. This galvanised steel capping fits over the offside rear roof corner, covering and...

Rubber Seal fits along the joint between the truck cab base and the rear body, sealing where the cab meets the tub. It forms a continuous barrier ...

Bodyside Seal for the lower edge of the rear upper body section, sealing the joint between the upper body structure and the lower body on the rear ...

Body Seal - a moulded rubber weather seal in the body & chassis assembly. It closes the gap between adjacent body panels to exclude water, dus...

Vent Lid Hinge Pin - hinge pin for the dash ventilator flap. This pin forms the pivot on which the dash fresh-air ventilator lid hinges, allowing ...

Grommet - rubber blanking grommet for the transmission (gearbox) tunnel cover. This rubber grommet seals the access aperture in the gearbox tunnel...

Roof Panel Seal - Right-Hand for the Defender 110 rear upper body, sealing the joint between the right-hand roof panel edge and the upper body stru...

Roof Panel Seal - Left-Hand for the Defender 110 rear upper body, sealing the joint between the left-hand roof panel edge and the upper body struct...

Clevis Pin for the bonnet stay. Forms the pivot at the upper end of the bonnet prop, retaining the stay to the bonnet.

Cab Body Panel Mounting Bracket - a body bracket that locates and secures a cab panel to the surrounding body structure. It provides the fixing po...

Bolt securing the bulkhead to the chassis outrigger. A 1/2" UNF hex-head bolt used at the lower bulkhead mounting points, where the bulkhead fixes...

Blanking Plug for closing an unused 16 mm (5/8") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Side Panel Buffer, a rubber buffer fitted at the rear body side panels. Sits between the upper and lower rear quarter panels, cushioning the joint...

Mounting stud

Seat Belt Bracket for the front seat belt, lower mounting, left-hand side. This bracket bolts to the seat box and provides the lower anchorage poi...

Door lock RH

Spare Wheel Bonnet Strap, the retaining strap for a bonnet-mounted spare wheel. Secures the spare wheel in the bonnet-top carrying position, holdi...

Headlamp Bezel is the outer retaining surround for the headlamp unit, mounting within the front lighting panel. It secures and finishes the lamp a...

Edge Clip - Door Lock Mechanism with various applications across Land Rover Series, Defender, Discovery 1, and Range Rover Classic models. This sp...

Rope Hook

Headlamp Guard in galvanised steel. A protective grille fitted over the headlamp lens to shield it from stone chips, debris and impact damage. The...

Headlamp Guard in moulded plastic. A protective guard fitted over the headlamp lens to shield it from stone chips, debris and impact damage. Suppl...

Air Vent Mechanism - operating mechanism for the dash-mounted fresh-air ventilator. Controls the opening and closing of the bulkhead air vent flap...

Dashboard Assembly Plate is a structural panel within the facia assembly, forming the mounting base onto which the instrument panel and dashboard t...

Instrument Cover is the trim cover for the instrument pack within the facia assembly, enclosing the main gauge cluster. It is also used as the cov...

Bonnet Hinge Bush for the Land Rover bonnet hinge assembly. This bush fits into the bore of the bonnet hinge, providing a wear surface around the ...

Door Check Arm Bracket is the pivot bracket in the door check assembly that anchors the check arm to the body at the rear door. The check arm runs...

Heater Air Intake Trim fits the front wing air intake of the heating and ventilation system. It finishes the fresh-air intake aperture in the wing...

Rear Sill Panel for the right-hand side of the body understructure on long wheelbase (109 inch) models. Fitted at the rear sill position, this pane...

Door Hinge Shim for the Land Rover door hinge assembly. This 1mm shim is fitted between the door hinge and its mounting face to set or adjust the ...

Bracket

Replace or upgrade the front outer wing panel on your Series 2/3 Land Rover with this aluminium panel designed for Right-Hand Side (RHS) and Left-H...

Radiator Panel for the front-end assembly on Series III models. This panel forms the surround and support structure for the radiator, integrating w...

Window Channel

Window Channel

Window Channel - Top is the upper glass-run channel that guides the top edge of the window glass, supplied as a 94 cm length. It forms the running...

Seat Frame for the adjustable driver's seat on Series II and Series III models. This structural frame forms the base of the driver's seat assembly.

Steel Ball for the timing chain tensioner, 7/32 in diameter. Seats within the tensioner mechanism to help maintain correct timing chain tension.