Products

Rubber Washer - Seat Backrest for Land Rover Series and Defender models. This rubber washer is used in the seat backrest assembly, fitting beneath...

Hook

Hose Clip Spring is the spring connector clip for the heater demister and air outlet pipes. Retains the demister ducting and outlet flaps within t...

Heater Control Mounting Plate for left-hand drive applications. Fitted within the heater control assembly in the cab interior, this plate provides ...

Shim door GENUINE - door striker plate 1958 - 1984 - side hinged tailgate

Grille Spring Clip for securing the front grille panel on Series III models. Fitted at the grille mounting points, this spring clip retains the fro...

Heater Cable operates the tap-type heater control valve in the heating and ventilation system. It connects the dashboard heater control to the tap...

Seat Base Corner Capping in plastic. Fitted at the outer corners of the front seat base frame, this capping provides a neat finished edge and prote...

Bush

Interior Mirror Plate is the base/fixing plate that mounts the interior rear-view mirror to the body. It is a three-hole mounting plate that faste...

Fuel Filter Centre Bolt for the diesel fuel filter and sedimentor assembly. This through-bolt clamps the filter bowl and element onto the filter h...

Fuel Tank Mounting Washer is used at the fuel tank mounting points, spreading the clamping load of the fixing across the mounting bracket or strap....

Door Latch Shim - Rear - a packing shim for the rear door anti-burst latch, part of the door lock and handle assembly. Fitted behind the latch on ...

Bump Stop for the suspension, mounted at the limit of axle travel. This rubber stop caps upward suspension movement at full compression, providing...

Door Check Strap Assembly A check strap that limits how far the side-hinged tailgate opens and holds it at its open position. Fitted to the lower ...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Fuel Filler Seal - sealing ring fitted at the fuel filler, part of the fuel tank filler assembly. Seals the joint at the filler neck to prevent fu...

Pedal Pin is the pivot pin in the pedal box assembly that locates the brake and clutch pedals. It passes through the pedal boss and the pedal moun...

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...

P-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...

Washer - Diesel Sedimentor is a sealing washer used in the diesel fuel sedimentor (fuel filter/water separator) assembly on diesel-engined Land Rov...

Gearbox Thrust Washer for the intermediate gear (laygear) in the main gearbox, used on 4-cylinder applications. It locates against the intermediat...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Filler and Level Plug for the V8 4-speed gearbox and for differential assemblies across a wide range of classic Land Rover models. Fitted at the s...

Flasher Lamp Lens - Sparto Type is the replaceable coloured lens for the Sparto-pattern direction indicator (flasher) lamp, forming part of the ext...

Valve Push Rod

Differential Shim - 0.072in, for the Rover-type differential. Fitted during differential setup to set bearing preload and gear alignment. Shim thi...

Water Pump Gasket - 7-Hole for the cooling system on Land Rover 4-cylinder military engines. This gasket seals the mating face between the water p...

Oil Filler Pipe Gasket seals the joint between the oil filler pipe and the engine front (timing) cover. Fitted at the filler pipe mounting flange,...

Fuel Pipe Olive for the fuel supply line. The olive is the compression ferrule that seats between the fuel pipe and its union fitting. When the un...

Differential Shim, 0.038in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Differential Shim, 0.038in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Differential Shim - 0.048in. Fitted during differential assembly to set bearing preload and gear alignment. Shim thickness is selected against mea...

Differential Shim for the crownwheel and pinion assembly. Fitted during differential assembly to set bearing preload and gear alignment. Shim thic...

Differential Pinion Shim - 0.052in. Fitted between the pinion head and its bearing to set pinion depth and preload during differential setup. Shim...

Shock Absorber Bush is a rubber mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chassis and axle attachme...

Radiator Overflow Hose carries coolant overflow away from the radiator filler neck. It connects to the overflow spigot on the radiator filler neck...

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...

Heater Control Pin

Military fuel cap

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Clutch Cap that closes an aperture in the clutch bellhousing around the release mechanism. Fitted over an opening in the bellhousing, the cap seal...

M6 Stud for the gearbox main casing. This threaded stud secures the speedometer drive housing to the transmission main casing, providing the fixin...

Washer