Products

Clutch Repair Kit

Kit - Caliper Brake Pad

Chassis Wiring Harness - Heated Rear Window & Rear Wiper is the rear body/chassis section of the wiring loom that supplies the heated rear wind...

Handbook - English Edition

Fuel Injection Pump Gear Retainer is a workshop special tool used when removing or refitting the fuel injection pump on the TDi diesel engine. It ...

Rear Crankshaft Oil Seal seated in the crankshaft rear oil seal housing at the back of the cylinder block, sealing the point where the crankshaft e...

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Cylinder Head Gasket for the 300TDi 2.5L four-cylinder turbo diesel engine, sealing the joint between the cylinder head and the engine block. It s...

Rocker Cover Gasket for the Rover V8 petrol engine, sealing the rocker (valve) cover to the cylinder head. The gasket seats between the cover flan...

Sump Gasket for the Td5 2.5L 5-cylinder turbo diesel engine. It seals the joint between the oil sump and the cylinder block within the engine lubri...

Thermostat Gasket for the Td5 2.5L 5-cylinder turbo diesel engine, sealing the coolant outlet elbow to the thermostat housing. It forms the coolan...

Gasket - Cover

Heat Shield Bracket for the exhaust manifold and turbocharger heat shield on the Duratorq TDCi (Puma) diesel engine. The bracket bolts to the exha...

Cam Cover Bolt for the Td5 2.5L 5-cylinder turbo diesel engine, securing the camshaft cover to the cylinder head. This is the flanged-head bolt th...

Crankshaft Pulley Bolt for the Td5 2.5L five-cylinder turbo diesel engine, securing the crankshaft pulley and torsional vibration damper to the nos...

Sealing Washer - 18 mm OD x 12 mm ID is a sealing washer with a 12 mm inner diameter and an 18 mm outer diameter, used to seal threaded unions and ...

Bonnet Staple - the fixed engagement point within the hand-operated bonnet locking assembly. This component mounts to the bonnet panel and interfa...

Door Check Strap Bracket – Rear – RH mounts the door check strap on the right-hand rear side door. The check strap limits how far the door swings ...

Bonnet Stop Buffer is a rubber buffer that cushions the bonnet where it rests against the body when closed. Mounted on the front bodywork, it supp...

Wheelguard - a protective guard fitted in the wheel arch area of the body. It shields the surrounding bodywork and underbody components from mud, ...

Handbrake Cover - the trim cover fitted around the base of the handbrake (parking brake) lever where it mounts on the transmission tunnel. It conc...

Handbrake cover LHD

Heater Controls Spacer - spacer fitted within the heater control assembly of the HVAC unit. Sold individually.

EGR Valve for the exhaust gas recirculation circuit on Td5 2.5L 5-cylinder turbo diesel and 2.0L L-Series diesel engines. The valve meters a contr...

Fuel Shut-Off Switch for the Td5 diesel fuel system - an inertia-operated safety switch wired into the fuel pump supply circuit. In the event of a...

EDC switch Puma

Switch - Fuel Shut-Off

Folding Side Step Mat - tread mat fitted to the folding side access step. Provides a non-slip stepping surface for entry and exit at the side doors.

Tailgate Hinge Bolt secures the tailgate hinge to the rear body in the tailgate hinge assembly. Used on High Capacity Pick Up (HCPU) body configur...

Rear Subframe Angle Bracket for the rear chassis and subframe assembly, in the High Capacity Pick Up (HCPU) configuration. The angled bracket prov...

Door Seal Retainer - Rear End for the rear door seal assembly. This retainer locates and secures the door weatherstrip in its channel along the re...

Hood Grab Handle for the soft top assembly. The handle is fitted to the soft top to provide a hand grip for occupants. It mounts to the hood frame...

Hoodstick Tube Guide is a tubular member of the soft top hood frame, locating and tying the hood sticks together to brace the folding frame that su...

Exterior Mirror with convex glass and a black finish, supplied as a complete door-mounted mirror assembly. The convex glass gives a wider rearward...

A-Post Finisher is the trim cover for the right-hand A-post, the windscreen pillar, concealing the pillar structure and dressing the join between t...

Glass

Instrument Panel is the moulded facia structure forming the dashboard, carrying the instrument binnacle, switch panel and heater control assembly a...

Decal