Products

Split Pin for the rear tailboard lower assembly. A split pin (cotter pin) passes through a drilled clevis or retaining pin and its legs are splaye...

Plastic Clip for the radiator and fan cowl assembly. The clip locates the cowl to the radiator and retains the surrounding cooling system trim, ho...

Output Shaft Washer - LT230 Transfer Box for the Defender Puma drivetrain assembly. This washer seats behind the output shaft flange at both the f...

Saddle Clip for the power steering hydraulic circuit. This saddle-shaped clip clamps a power steering pipe or hose to its mounting point, retaining...

Upper Steering Column Shroud is the moulded cover fitted over the top section of the steering column. It encloses the upper column and the mountin...

36 Spline Steering Wheel with a black leather rim. It mounts on the 36 spline upper steering column shaft and is retained by the column nut. The s...

Rivet - 3.2 x 8 mm body and chassis fastener. Used in the rear end door check mechanism (lever type), spare wheel carrier mountings and auxiliary ...

Panhard Rod Bush from the front suspension's lateral location linkage. The Panhard rod controls sideways movement of the axle relative to the body...

Damper Mounting Bush - Lower - isolating bush for the lower shock absorber mounting. The bush sits between the damper mounting and its bracket, is...

Tailgate Cable Stud is the anchor point for the rear tailgate support cable. Mounted on the rear body, the stud receives the end of the tailgate c...

Door Check Bracket - Rear is a mounting bracket within the rear door check mechanism. It anchors the door checker (door stay) to the body, providi...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Oil Seal Retainer for the front axle swivel housing assembly. This retaining plate holds the swivel housing oil seal square against the chrome swiv...

Front Shock Absorber - hydraulic damper for the front suspension, supplied with its mounting hardware. The damper controls the rate at which the f...

Lock Washer secures the retaining hardware on the layshaft (countershaft) within the manual gearbox. A tab on the washer is folded against the ret...

Brake Shoe Screw - a retaining screw within the drum brake assembly that secures the brake shoe in position. It holds the shoe located against the...

Bonnet Striker Kit - the striker for the bonnet locking assembly. The striker is the fixed catch plate that the bonnet lock and safety catch engage...

Oil Filter for the engine lubrication system of the 2.25L four-cylinder petrol and diesel engine. The filter traps combustion by-products, metal p...

Alternator Brush Set - the carbon brushes for the alternator, part of the charging circuit. The brushes bear on the rotor slip rings to carry field...

Oil Seal for the swivel pin housing on the front axle, sealing against the polished surface of the swivel ball. The seal seats in the rear face of...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Screw for securing the rear reflector, fog lamp, and reverse lamp assembly on the Land Rover Defender. Used to retain the lamp cluster components ...

Piston ring set petrol 2,25 020 Mahle (per zuiger)

Steering Box Sector Shaft for the Adwest power-steering box. The sector shaft is the output shaft of the recirculating-ball steering box. The worm...

Vacuum Advance Unit for the ignition distributor on the 3.5L V8 petrol engine. This vacuum capsule mounts on the side of the distributor and conne...

Actuator

Intercooler Hose for the 200 TDi 2.5L turbo-diesel charge-air system (non-catalyst configuration). The hose carries pressurised charge air between...

O-Ring for the ZF automatic gearbox oil pump, sealing the pump housing within the gearbox casing. The ZF oil pump is an internally-driven unit tha...

Pulley

Corner Fixing Plate - pressed retaining plate for the automatic transmission sump pan, corner position. The sump pan on the ZF four-speed automati...

Hexagonal Screw - sump pan retaining screw for the ZF four-speed automatic transmission. The screw passes through one of the pressed retaining pla...

Distributor Repair Kit

Piston Assembly for the 2.5L 4-cylinder turbo diesel engine, machined to +0.020" oversize for a rebored cylinder block. The piston transfers combu...

Lucar Connector - a fully insulated two-way in-line electrical connector for joining wiring within the loom. Of the Lucar (blade) terminal type, i...

Sill Panel - LH for the Defender 110 Station Wagon and Crew Cab body variants, forming the exterior body panel along the left-hand lower sill line ...

Headlamp mounting panel RH

Bulb & Holder for the instrument panel warning lights. The assembly pairs an illumination bulb with its holder, which fits into the rear of the...