Products

Wiring Connector for the chassis wiring harness, used in the fuel tank circuitry. The connector forms a serviceable electrical junction between ha...

Ignition Lead Set for the 3.5L Rover V8 petrol engine, carrying the high-tension spark from the distributor to the spark plugs. The set comprises ...

Rotor Arm for the 24V shielded ignition distributor. The rotor arm mounts on the top of the distributor shaft and, as it rotates, routes the high-t...

A/C System Clamp is a securing clamp used within the air conditioning and heater (HVAC) system. It retains components of the A/C intake and distri...

A/C Evaporator Seal seals the evaporator assembly within the air conditioning system's HVAC housing. Fitted at the evaporator core interface to pr...

Rear Floor Mat Set is a drop-in moulded rubber mat set for the rear floor area. The mats locate over the rear footwell and floor pan to protect th...

Brush kit RTC830 fits: Rover 3.5L V8 startermotor type 3M100 - S3 109" stage 1 V8 - 101" Forward Control - Range Rover Classic

Rivet - body fixing used in the rear cab panel and sliding side window assembly. Secures the panel and window frame to the surrounding body struct...

Body Rivet - a mechanical fastener used within the body and panel assembly to join thin sheet metal, trim and stowage fittings. Nominal size 3/16"...

Body Rivet - general-purpose body fixing used across the cab structure, front wings, hood sticks, rear body cappings and panels, and door seal rete...

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Bolt - Hexagon Head used in engine and interior fascia assembly applications. This hexagon head fastener is used in the EGR system assembly and in...

Screw

Bolt and Washer - an M8 x 24mm bolt supplied with a washer, used as a general-purpose fixing across several Land Rover assemblies. The washer spre...

Bolt Secures the radius arm to the axle bracket within the radius arms & links assembly. Installed through the radius arm bush and axle mounti...

Bolt - Flanged Hex

Nut - an M8 x 1.25 captive U-spring nut used to mount the air suspension compressor. The spring-steel body clips over the chassis bracket to provi...

Screw - an M6 x 20 mm pan-head setscrew with a Torx drive, used as a general multi-application fastener. The Torx socket gives positive tool engag...

Bolt

Pan Head Screw, M8 x 25mm. Metric pan head screw for use across Land Rover body, chassis, and accessory fitment applications.

Pan Head Bolt, M8 x 40mm. Metric pan head bolt for use across Land Rover body, chassis, and interior assemblies.

Screw is an M4 x 8mm fastener used in the door mirror assembly, securing components of the interior and exterior mirrors at their mounting points. ...

Front Brake Pad Set for the front braking system, comprising the friction pads that seat in the front calipers. Under hydraulic pressure the calip...

Brake Pipe Assembly for the front brake hydraulic circuit on vehicles equipped with four-wheel ABS. The rigid pipe carries pressurised brake fluid...

Pipe assembly brake

Brake Pipe Clip is a retaining clip from the front brake line mounting hardware. The double form holds two rigid brake pipes side by side at a fix...

Brake Pipe Clip secures and routes rigid brake pipe runs within the braking system, holding the pipe against the chassis or body to maintain its ro...

Brake Pipe T-Piece is a three-way hydraulic union in the rear braking circuit, joining the incoming brake line to the two rigid pipes that feed the...

scew hexagonal head M6 x 45mm 4-speed LT95 and 5-speed gearbox bottom cover plate (with Rover V8 engine)

Screw, M6 x 45, used as a threaded fastener at several points in the drivetrain and pedal assemblies. It secures the lower bellhousing cover to th...

Set Screw - a fully threaded hexagonal-head setscrew with an M10 metric thread and a 20 mm length. A general-purpose fixing used at fastening point...

Bolt - a hexagonal-head bolt with a 5/16" UNC (Unified Coarse) imperial thread and a 3/4" length. Used as an engine-assembly fixing, including cams...

Set Screw - a fully threaded hexagonal-head setscrew with a 3/8" UNC (Unified Coarse) imperial thread and a 7/8" length. Used as a Rover V8 engine-...

Bolt Set Screw 7/16UNC x 1.25" 2.25L diesel: startermotor to engine (Imperial, non-metric engines) 2.6L petrol: oil filter housing to adaptor

Flywheel Bolt, 7/16" UNC x 1" hexagonal head, securing the flywheel to the rear crankshaft flange. Used on V8 petrol engines with manual transmiss...

Brake Caliper Bleed Screw - the bleed nipple that threads into the brake caliper. Backing the screw off releases trapped air and old fluid from th...

Handbrake Operating Lever from the parking brake control assembly. The lever is the driver-operated arm that applies the transmission brake through...