Products

Screw – a black self-tapping screw with a pan head and Pozidriv drive recess, size No. 10 × 5/8 in, used to secure body, trim and panel fixings. B...

Screw - a No. 10 x 1" pan-head self-tapping screw used across interior and door assemblies. It secures the window regulator and door glass channel...

Screw - No.10 x 1" Pan head, self-tapping, pointed fastener used in door trim and window regulator assemblies. It secures the interior grab handle...

Self-Tapping Screw Set is a set of general-purpose self-tapping fixings used at panel, trim, finisher and bracket mounting points throughout the ve...

Self-Tapping Screw securing the heater assembly within the HVAC housing on diesel applications. This screw forms part of the heater box fixing har...

Cable Tie for securing wiring looms and cables in Land Rover applications.

Resistor Assembly sets the blower motor fan speeds within the heating and air conditioning system. Wired in series with the blower motor on the lo...

Carburettor Overhaul Kit for the 2.25L four-cylinder petrol engine. The kit renews the perishable sealing and metering components of the carburetto...

Carburettor Float Needle is the needle valve that regulates fuel entry into the carburettor float chamber. Actuated by the float, it seats to shut...

Tab Washer for the steering box drop arm retaining nut. This lock washer sits under the nut on the steering box output shaft. Once the nut is torq...

Starter Motor Brush Kit for the Lucas M113-type starter motor in the engine starting system. The brushes bear on the armature commutator to transf...

Reinforcement is a structural stiffener for the lower rear body. It fits to the lower section of the rear body structure to add rigidity to the sur...

Pipe Clip used to secure and route pipework such as fuel breather and roll-over anti-spill lines. The clip holds the pipe at a fixed point to prev...

Body Washer, 22mm outer diameter, 6.5mm inner diameter. A flat washer that spreads the clamping load of a fixing across the mounting surface, prot...

Washer for the bonnet insulation pad. This washer retains the sound- and heat-insulation pad against the underside of the bonnet, holding the pad ...

Plastic Drive Rivet - Wheel Arch Trim secures exterior trim panels to the body as part of the wheel arch trim fixing set. This one-piece expanding...

Sealing Washer - a sealing washer used at cylinder head and thermostat housing joints within the cooling and lubrication circuit. Fitted beneath a...

Tilt Stud for the soft top (tilt) and hood frame fixing. Mounts to the body to receive the retaining plate that secures the canopy tilt to the veh...

G-Hook - a hook fitting for the soft top drain channel. It anchors and tensions the drain channel that runs along the soft top, holding the channe...

Hazard Warning Switch for the fascia switch panel. Push-push (push-on/push-off) switch that operates the hazard warning flasher circuit.

Nut Plate for the body-side striker mountings, part of the door and tailboard latch assembly. The plate provides captive threaded anchor points be...

Vent Assembly Knob for the dashboard air vent control on models without air conditioning. The knob fits onto the vent control lever and provides t...

Spire Nut (U-type spire fastener) for trim and panel fixings. Spring-steel push-on nut that clips over a panel edge or stud to provide a captive f...

Spire Nut - a spring U-type nut that slides over a panel edge to receive a self-tapping screw. It provides a captive threaded seat where there is ...

Spring Nut A clip-on spring-steel fastener, also known as a speed nut, used across body, grille and chassis fittings. It slides over a panel edge ...

Rear Lower Wheelarch is a body panel forming the lower section of the rear wheelarch on the 110" wheelbase Station Wagon bodyshell. It defines the ...

Bar - Torsion

Door Latch Adjuster. Part of the door latch mechanism, it sets the striker engagement so the door aligns, closes and seals correctly. It serves the...

Body Seal seals the joint at the lower edge of the rear upper body section on Hard Top models. The single seal serves both the left- and right-han...

Truck Cab Waist Seal for the Land Rover Defender truck cab body variant. This rubber seal fits at the waist level of the truck cab body, sealing t...

Front Door Outer Waist Seal fitted along the upper edge of the front door outer panel, sealing the interface between the outer panel and the door d...

Rear Door Outer Waist Seal - Left-Hand fitted along the upper edge of the left-hand rear side door outer panel, sealing the interface between the o...

Rear Door Outer Waist Seal - Right-Hand fitted along the upper edge of the right-hand rear side door outer panel, sealing the interface between the...

Tailgate Seal, rubber weatherseal for the rear tailgate. It fits around the tailboard aperture, sealing the joint between the closed tailgate and ...

Front Door Glass Guide channels the window glass as it travels within the front door. This run guide locates the edge of the door glass and keeps ...

Tailgate Assembly is the complete side-hinged lower tailgate (tailboard) for the rear of the vehicle, carrying the externally mounted spare wheel. ...

Bonnet Release Cable, part of the bonnet latch and release mechanism. The cable connects the interior release lever to the bonnet lock, transmitti...

Bonnet Release Cable connects the cabin-mounted release lever to the bonnet latch as part of the bonnet locking mechanism. Pulling the interior le...

Body Side Frame Assembly forms the left-hand structural side frame of the bodyshell. It provides the framework to which the outer body panels, door...

Filler - Rear Quarter Panel

Body Finisher - Rear Capping - RH for the rear body on the Defender 110 two-door hard top and soft top. This right-hand rear body capping finisher...