Products

Spacer - Hinge

Door Vertical Filler for the door sealing trim. This vertical rubber filler closes the gap at the rear edge of the front doors and at the front and...

Door Filler - Top - Front is the horizontal filler strip that runs along the top edge of the front door frame. It closes the channel at the top of...

Door Glass Channel Shim - a spacer used within the front door to set the glass run channel against the window regulator. The shim takes up clearan...

Linkage

Bolt - Lower Steering Shaft UJ is the M8 x 35 mm clamp bolt that secures the universal joint at the lower steering shaft, within the steering colum...

Bolt Exhaust manifold fixing bolt, 5/8" UNC x 5-1/2", for the 3.5L V8 petrol engine. Secures the exhaust manifold to the cylinder head within the ...

Needle Valve Kit Float-chamber needle valve and seat for the Zenith Stromberg 175CD carburettor, fitted to the 3.5L V8 petrol engine. The needle v...

Bonnet - Less Hinges for the Defender Puma era body assembly. This bonnet panel is taller and wider than the pre-2007 Defender bonnet, with a dist...

Clip

Decal - TDi - a self-adhesive "TDi" engine decal for the front wing, in light grey and measuring 9cm. The decal reproduces the original "TDi" wing...

Decal

Decal

Front Grille Badge is the model identification badge fitted to the front grille panel. It mounts to the grille to carry the marque branding at the...

Land Rover Logo Tape - adhesive decal, 25cm length. Self-adhesive Land Rover logo tape from the Defender transfers and graphics range. Applied to ...

Body Decal reading 'Defender 110' - an exterior self-adhesive graphic finished in silver lettering on a clear backing. The decal is applied to the...

Heater Hose forming part of the cabin heater coolant circuit, carrying feed coolant from the engine cooling system to the heater matrix. For the 2...

Differential Lock Instruction Label, a self-adhesive label applied to the fuse box cover showing the operating instructions for the differential lo...

Differential Lock Instruction Label, a self-adhesive label applied to the fuse box cover showing the operating instructions for the differential lo...

Screw is a fixing screw used to secure exterior lamp, interior lamp and trim components to the body. It retains fittings such as the high-level st...

Defender 110 Decal - black, approximately 26cm length. Self-adhesive black Defender 110 model identification decal from the Defender transfers and...

TDi Decal for Defender 110. Original-specification exterior decal carrying the TDi designation. Applied to the body as part of the standard factor...

Front Seat Belt Assembly - right-hand inertia reel unit in the occupant restraint system. Installed at the front right-hand seating position, it p...

Window Regulator Escutcheon - trim bezel that fits where the window winder handle passes through the door trim panel. The escutcheon sits between ...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Front Seat Belt Assembly - the left-hand front inertia-reel belt, part of the front seat belt restraint system for soft-top configurations. It is ...

Body-Side Name Plate, a moulded plastic decal applied to the body side. Fitted as exterior body-side trim identifying the V8 petrol variant.

Rivet used to secure exterior body panels and mouldings, including front wing and body-moulding assemblies. Installed through the panel to retain ...

Transmission Tunnel Cover - a moulded rubber cover that fits over the transmission tunnel in the front floor, between the driver and passenger foot...

Decal - ZF Automatic Gearbox is an adhesive identification label associated with the ZF automatic transmission, located in the centre console and c...

Instrument Finisher for the left-hand side of the facia (dashboard) instrument panel. The finisher frames and trims the instrument area, retaining...